CHECK()
, DCHECK()
, NOTREACHED_NORETURN()
and NOTREACHED()
are all used to ensure that invariants hold. They document (and verify) programmer expectations that either some statement always holds true at the point of (D)CHECK
ing or that a piece of code is unreachable. They should not be used to validate data that is provided by end-users or website developers. Such data is untrusted, and must be validated by standard control flow.
An invariant that does not hold should be seen as Undefined Behavior, and continuing past it puts the program into an unexpected state. This applies in particular to DCHECK()
and NOTREACHED()
since they do not test anything in production and thus do not stop the program from continuing with the invariant being violated. All invariant failures should be seen as P1 bugs, regardless of their crash rate. Continuing past an invariant failure can cause crashes and incorrect behaviour for our users, but also frequently presents security vulnerabilities as attackers may leverage the unexpected state to take control of the program. In the future we may let the compiler assume and optimize around DCHECK()
s holding true in non-DCHECK builds using __builtin_assume()
, which further formalizes undefined behavior.
Failure can come from beyond Chromium‘s ability to control. These failures should not be caught with invariants, but handled as part of regular control flow. In the rare case where it’s impossible to safely recover from failure use base::ImmediateCrash()
to terminate the process instead of using CHECK()
etc. Doing so avoids implying that the generated crash reports should be triaged as bugs in Chromium. Fatally aborting is a last-resort measure.
We must be resilient to a bad prior release of Chromium which may have persisted bad data to disk or a bad server-side rollout which may be sending us incorrect or unexpected configs.
Note that wherever CHECK()
is inappropriate, DCHECK()
is inappropriate as well. DCHECK()
should still only be used for invariants. Ideally we‘d have better test coverage for failures created from outside Chromium’s control.
Non-exhaustive list of failures beyond Chromium's control:
base::ImmediateCrash()
.CHECK()
for bad syntax, etc.CHECK()
s as a bad server-side rollout shouldn‘t be able to bring down the client. Note that you may CHECK()
that data is valid after the caller should’ve validated it.base::ImmediateCrash()
or CHECK()
etc. as part of normal control flow.CHECK()
its result as we expect the rug to be pulled from under our feet. In the case of hardware failure we should not for instance CHECK()
that a write succeeded.In some cases (malware, ..., dll injection, etc.) third-party code outside of our control can cause us to trigger various CHECK() failures, due to injecting code or unexpected state into Chrome. These can create “weird machines” that are useful to attackers. We don't remove CHECKs just to support them, though we may handle these unexpected states if possible and necessary. Chromium is not designed to run against arbitrary code modification.
Prefer CHECK()
and NOTREACHED_NORETURN()
as they ensure that if an invariant fails, the program does not continue in an unexpected state, and we hear about the failure either through a test failure or a crash report. This helps prevent user harm such as security bugs when our software does what we did not expect. Historically, CHECK()
was seen as expensive but great effort and care has gone into making the crash instructions nearly free on modern CPUs. Log messages are discarded from CHECK()
s in production builds but provide additional information in debug and DCHECK
builds.
DCHECK()
(and DCHECK_EQ()
, DCHECK_LT()
, etc) provide a fallback mechanism to check for invariants where the test being performed is too expensive (either in terms of generated code size or performance) to verify in production builds. The risk of depending on DCHECK()
is that, since it disappears in production builds, it only exists in tests, on developer machines and a very small subset of Canary builds. Any side effects intended to happen inside the DCHECK()
disappear from production along with it, and unexpected behaviour can happen afterward as a result.
NOTREACHED_NORETURN()
signals that a piece of code is intended to be unreachable, and lets the compiler optimize based on that fact, while terminating if it is in fact reached. Like CHECK()
, this ensures we hear about the invariant failing through a test failure or a crash report, and prevents user harm. Historically we used the shorter NOTREACHED()
to indicate code was unreachable, however it disappears in production builds and we have observed that these are in fact commonly reached. Prefer NOTREACHED_NORETURN()
in new code, while we migrate the preexisting cases to it with care. See https://crbug.com/851128.
Below are some examples to explore the choice of CHECK()
and its variants:
// Good: // // Testing pointer equality is very cheap so write this as a CHECK. A security // bug would happen afterward if the CHECK fails (in this case, on the next // line). auto it = container.find(key); CHECK(it != container.end()); *it = Foo(); // Good: // // This is an expensive operation. Consider writing a test to provide coverage // for this as well. DCHECK() is available as a fallback to verify the condition // in tests and on a small subset of Canary builds. DCHECK(|invoke an O(n^2) operation|); // Good: // // This switch handles all cases, but enums can technically hold any integer // value (even if all enum members are enumerated), so the compiler must try to // handle other cases too. We can avoid dealing with values outside enums by // using NOTREACHED_NORETURN() while also making sure we hear about it. switch (my_enum) { case A: return 1; case B: return 5; case C: return 3; } NOTREACHED_NORETURN(); // Bad: // // Do not handle `DCHECK()` failures. Use `CHECK()` instead and omit the // conditional below. DCHECK(foo); // Use CHECK() instead and omit conditional below. if (!foo) { ... } // Bad: // // Use CHECK(bar); instead. if (!bar) { NOTREACHED(); return; }
If you‘re not confident that an unexpected situation can’t happen in practice, an additional base::NotFatalUntil::M120
argument after the condition may be used to gather non-fatal diagnostics before turning fatal in a future milestone. Make sure to either prioritize these invariant failures once discovered, and punt the milestone where this invocation turns fatal to avoid rolling out a stability risk. Macros with a base::NotFatalUntil
argument will provide non-fatal crash reports before the fatal milestone is hit. They preserve and upload logged arguments that are uploaded along the report which is useful for debugging failures as well.
This extra argument can be used to more cautiously add or upgrade to CHECK()
s. This is appropriate when we‘re uncertain of whether the invariant currently holds true or when there’s low pre-stable coverage. Specifically consider using these:
DCHECK()s
.As base::NotFatalUntil
automatically turns fatal, keep an extra eye on automatically-filed bugs for failures in the wild. Discovered failures, like other invariant failures, are high-priority issues. Once resolved, either by handling the unexpected situation or making sure it no longer happens, the milestone number should be bumped to allow for validation in stable channels before turning fatal.
Failing instances should not downgrade to DCHECKs as that hides the ongoing problem rather than resolving it. In rare exceptions you could use DUMP_WILL_BE_CHECK()
macros for similar semantics (report on failure) without timeline expectations, though in this case you must also handle failure as best you can as failures are known to happen.
For failures in tests, GoogleTest macros such as EXPECT_*
, ASSERT_*
or ADD_FAILURE()
are more appropriate than CHECKing
. For production code:
LOG(DFATAL)
is fatal on bots running tests but only logs an error in production.DLOG(FATAL)
is fatal on bots running tests and does nothing in production.As these only cause tests to fail, they should be rarely used, and mostly exist for pre-existing code. Prefer to write a test that covers these scenarios and verify the code handles it, or use a fatal CHECK()
to actually prevent the case from happening.