| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2006 Jon Dufresne <jon.dufresne@gmail.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #include <assert.h> |
| #include <spd.h> |
| #include <sdram_mode.h> |
| #include <stdlib.h> |
| #include <delay.h> |
| #include "i855.h" |
| |
| /*----------------------------------------------------------------------------- |
| Macros and definitions: |
| -----------------------------------------------------------------------------*/ |
| |
| #define VALIDATE_DIMM_COMPATIBILITY |
| |
| /* Debugging macros. */ |
| #if CONFIG_DEBUG_RAM_SETUP |
| #define PRINTK_DEBUG(x...) printk(BIOS_DEBUG, x) |
| #define DUMPNORTH() dump_pci_device(NORTHBRIDGE_MMC) |
| #else |
| #define PRINTK_DEBUG(x...) |
| #define DUMPNORTH() |
| #endif |
| |
| #define delay() udelay(200) |
| |
| #define VG85X_MODE (SDRAM_BURST_4 | SDRAM_BURST_INTERLEAVED | SDRAM_CAS_2_5) |
| |
| /* DRC[10:8] - Refresh Mode Select (RMS). |
| * 0x0 for Refresh Disabled (Self Refresh) |
| * 0x1 for Refresh interval 15.6 us for 133MHz |
| * 0x2 for Refresh interval 7.8 us for 133MHz |
| * 0x7 for Refresh interval 64 Clocks. (Fast Refresh Mode) |
| */ |
| #define RAM_COMMAND_REFRESH 0x1 |
| |
| /* DRC[6:4] - SDRAM Mode Select (SMS). */ |
| #define RAM_COMMAND_SELF_REFRESH 0x0 |
| #define RAM_COMMAND_NOP 0x1 |
| #define RAM_COMMAND_PRECHARGE 0x2 |
| #define RAM_COMMAND_MRS 0x3 |
| #define RAM_COMMAND_EMRS 0x4 |
| #define RAM_COMMAND_CBR 0x6 |
| #define RAM_COMMAND_NORMAL 0x7 |
| |
| /* DRC[29] - Initialization Complete (IC). */ |
| #define RAM_COMMAND_IC 0x1 |
| |
| struct dimm_size { |
| unsigned int side1; |
| unsigned int side2; |
| }; |
| |
| static const uint32_t refresh_frequency[] = { |
| /* Relative frequency (array value) of each E7501 Refresh Mode Select |
| * (RMS) value (array index) |
| * 0 == least frequent refresh (longest interval between refreshes) |
| * [0] disabled -> 0 |
| * [1] 15.6 usec -> 2 |
| * [2] 7.8 usec -> 3 |
| * [3] 64 usec -> 1 |
| * [4] reserved -> 0 |
| * [5] reserved -> 0 |
| * [6] reserved -> 0 |
| * [7] 64 clocks -> 4 |
| */ |
| 0, 2, 3, 1, 0, 0, 0, 4 |
| }; |
| |
| static const uint32_t refresh_rate_map[] = { |
| /* Map the JEDEC spd refresh rates (array index) to i855 Refresh Mode |
| * Select values (array value) |
| * These are all the rates defined by JESD21-C Appendix D, Rev. 1.0 |
| * The i855 supports only 15.6 us (1), 7.8 us (2) and |
| * 64 clock (481 ns) (7) refresh. |
| * [0] == 15.625 us -> 15.6 us |
| * [1] == 3.9 us -> 481 ns |
| * [2] == 7.8 us -> 7.8 us |
| * [3] == 31.3 us -> 15.6 us |
| * [4] == 62.5 us -> 15.6 us |
| * [5] == 125 us -> 15.6 us |
| */ |
| 1, 7, 2, 1, 1, 1 |
| }; |
| |
| #define MAX_SPD_REFRESH_RATE ((sizeof(refresh_rate_map) / sizeof(uint32_t)) - 1) |
| |
| /*----------------------------------------------------------------------------- |
| SPD functions: |
| -----------------------------------------------------------------------------*/ |
| |
| static void die_on_spd_error(int spd_return_value) |
| { |
| if (spd_return_value < 0) |
| PRINTK_DEBUG("Error reading SPD info: got %d\n", spd_return_value); |
| /* |
| if (spd_return_value < 0) |
| die("Error reading SPD info\n"); |
| */ |
| } |
| |
| /** |
| * Calculate the page size for each physical bank of the DIMM: |
| * |
| * log2(page size) = (# columns) + log2(data width) |
| * |
| * NOTE: Page size is the total number of data bits in a row. |
| * |
| * @param dimm_socket_address SMBus address of DIMM socket to interrogate. |
| * @return log2(page size) for each side of the DIMM. |
| */ |
| static struct dimm_size sdram_spd_get_page_size(u8 dimm_socket_address) |
| { |
| uint16_t module_data_width; |
| int value; |
| struct dimm_size pgsz; |
| |
| pgsz.side1 = 0; |
| pgsz.side2 = 0; |
| |
| // Side 1 |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); |
| die_on_spd_error(value); |
| |
| pgsz.side1 = value & 0xf; // # columns in bank 1 |
| |
| /* Get the module data width and convert it to a power of two */ |
| value = spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_MSB); |
| die_on_spd_error(value); |
| |
| module_data_width = (value & 0xff) << 8; |
| |
| value = spd_read_byte(dimm_socket_address, SPD_MODULE_DATA_WIDTH_LSB); |
| die_on_spd_error(value); |
| |
| module_data_width |= (value & 0xff); |
| |
| pgsz.side1 += log2(module_data_width); |
| |
| /* side two */ |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); |
| die_on_spd_error(value); |
| |
| /* |
| if (value > 2) |
| die("Bad SPD value\n"); |
| */ |
| if (value > 2) |
| PRINTK_DEBUG("Bad SPD value\n"); |
| |
| if (value == 2) { |
| pgsz.side2 = pgsz.side1; // Assume symmetric banks until we know differently |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_COLUMNS); |
| die_on_spd_error(value); |
| |
| if ((value & 0xf0) != 0) { |
| // Asymmetric banks |
| pgsz.side2 -= value & 0xf; /* Subtract out columns on side 1 */ |
| pgsz.side2 += (value >> 4) & 0xf; /* Add in columns on side 2 */ |
| } |
| } |
| |
| return pgsz; |
| } |
| |
| /** |
| * Read the width in bits of each DIMM side's DRAMs via SPD (i.e. 4, 8, 16). |
| * |
| * @param dimm_socket_address SMBus address of DIMM socket to interrogate. |
| * @return Width in bits of each DIMM side's DRAMs. |
| */ |
| static struct dimm_size sdram_spd_get_width(u8 dimm_socket_address) |
| { |
| int value; |
| struct dimm_size width; |
| |
| width.side1 = 0; |
| width.side2 = 0; |
| |
| value = spd_read_byte(dimm_socket_address, SPD_PRIMARY_SDRAM_WIDTH); |
| die_on_spd_error(value); |
| |
| width.side1 = value & 0x7f; // Mask off bank 2 flag |
| |
| if (value & 0x80) { |
| width.side2 = width.side1 << 1; // Bank 2 exists and is double-width |
| } else { |
| // If bank 2 exists, it's the same width as bank 1 |
| value = spd_read_byte(dimm_socket_address, SPD_NUM_DIMM_BANKS); |
| die_on_spd_error(value); |
| |
| #ifdef ROMCC_IF_BUG_FIXED |
| if (value == 2) |
| width.side2 = width.side1; |
| #else |
| switch (value) { |
| case 2: |
| width.side2 = width.side1; |
| break; |
| |
| default: |
| break; |
| } |
| #endif |
| } |
| |
| return width; |
| } |
| |
| /** |
| * Calculate the log base 2 size in bits of both DIMM sides. |
| * |
| * log2(# bits) = (# columns) + log2(data width) + |
| * (# rows) + log2(banks per SDRAM) |
| * |
| * Note that it might be easier to use SPD byte 31 here, it has the DIMM size |
| * as a multiple of 4MB. The way we do it now we can size both sides of an |
| * asymmetric DIMM. |
| * |
| * @param dimm SMBus address of DIMM socket to interrogate. |
| * @return log2(number of bits) for each side of the DIMM. |
| */ |
| static struct dimm_size spd_get_dimm_size(unsigned dimm) |
| { |
| int value; |
| |
| // Start with log2(page size) |
| struct dimm_size sz = sdram_spd_get_page_size(dimm); |
| |
| if (sz.side1 > 0) { |
| value = spd_read_byte(dimm, SPD_NUM_ROWS); |
| die_on_spd_error(value); |
| |
| sz.side1 += value & 0xf; |
| |
| if (sz.side2 > 0) { |
| // Double-sided DIMM |
| if (value & 0xF0) |
| sz.side2 += value >> 4; // Asymmetric |
| else |
| sz.side2 += value; // Symmetric |
| } |
| |
| value = spd_read_byte(dimm, SPD_NUM_BANKS_PER_SDRAM); |
| die_on_spd_error(value); |
| |
| value = log2(value); |
| sz.side1 += value; |
| if (sz.side2 > 0) |
| sz.side2 += value; |
| } |
| |
| return sz; |
| } |
| |
| /** |
| * Scan for compatible DIMMs. |
| * |
| * @return A bitmask indicating which sockets contain a compatible DIMM. |
| */ |
| static uint8_t spd_get_supported_dimms(void) |
| { |
| int i; |
| uint8_t dimm_mask = 0; |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| u8 dimm = DIMM0 + i; |
| |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| struct dimm_size page_size; |
| struct dimm_size sdram_width; |
| #endif |
| int spd_value; |
| |
| if (dimm == 0) |
| continue; // No such socket on this mainboard |
| |
| if (spd_read_byte(dimm, SPD_MEMORY_TYPE) != SPD_MEMORY_TYPE_SDRAM_DDR) |
| continue; |
| |
| #ifdef VALIDATE_DIMM_COMPATIBILITY |
| if ((spd_value = spd_read_byte(dimm, SPD_MODULE_VOLTAGE)) != SPD_VOLTAGE_SSTL2) { |
| PRINTK_DEBUG("Skipping DIMM with unsupported voltage: %02x\n", spd_value); |
| continue; // Unsupported voltage |
| } |
| |
| /* |
| // E7501 does not support unregistered DIMMs |
| spd_value = spd_read_byte(dimm, SPD_MODULE_ATTRIBUTES); |
| if (!(spd_value & MODULE_REGISTERED) || (spd_value < 0)) { |
| PRINTK_DEBUG("Skipping unregistered DIMM: %02x\n", spd_value); |
| continue; |
| } |
| */ |
| |
| page_size = sdram_spd_get_page_size(dimm); |
| sdram_width = sdram_spd_get_width(dimm); |
| |
| // Validate DIMM page size |
| // The i855 only supports page sizes of 4, 8, 16 KB per channel |
| // NOTE: 4 KB = 32 Kb = 2^15 |
| // 16 KB = 128 Kb = 2^17 |
| |
| if ((page_size.side1 < 15) || (page_size.side1 > 17)) { |
| PRINTK_DEBUG("Skipping DIMM with unsupported page size: %d\n", page_size.side1); |
| continue; |
| } |
| |
| // If DIMM is double-sided, verify side2 page size |
| if (page_size.side2 != 0) { |
| if ((page_size.side2 < 15) || (page_size.side2 > 17)) { |
| PRINTK_DEBUG("Skipping DIMM with unsupported page size: %d\n", page_size.side2); |
| continue; |
| } |
| } |
| // Validate SDRAM width |
| // The i855 only supports x8 and x16 devices |
| if ((sdram_width.side1 != 8) && (sdram_width.side1 != 16)) { |
| PRINTK_DEBUG("Skipping DIMM with unsupported width: %d\n", sdram_width.side2); |
| continue; |
| } |
| |
| // If DIMM is double-sided, verify side2 width |
| if (sdram_width.side2 != 0) { |
| if ((sdram_width.side2 != 8) |
| && (sdram_width.side2 != 16)) { |
| PRINTK_DEBUG("Skipping DIMM with unsupported width: %d\n", sdram_width.side2); |
| continue; |
| } |
| } |
| #endif |
| // Made it through all the checks, this DIMM is usable |
| dimm_mask |= (1 << i); |
| } |
| |
| return dimm_mask; |
| } |
| |
| /*----------------------------------------------------------------------------- |
| SDRAM configuration functions: |
| -----------------------------------------------------------------------------*/ |
| |
| static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits) |
| { |
| int i; |
| u32 reg32; |
| uint8_t dimm_start_32M_multiple = 0; |
| uint16_t i855_mode_bits = jedec_mode_bits; |
| |
| /* Configure the RAM command. */ |
| reg32 = pci_read_config32(NORTHBRIDGE_MMC, DRC); |
| reg32 &= ~(7 << 4); |
| reg32 |= (command << 4); |
| PRINTK_DEBUG(" Sending RAM command 0x%08x\n", reg32); |
| pci_write_config32(NORTHBRIDGE_MMC, DRC, reg32); |
| |
| // RAM_COMMAND_NORMAL is an exception. |
| // It affects only the memory controller and does not need to be "sent" to the DIMMs. |
| |
| if (command != RAM_COMMAND_NORMAL) { |
| |
| // Send the command to all DIMMs by accessing a memory location within each |
| // NOTE: for mode select commands, some of the location address bits |
| // are part of the command |
| |
| // Map JEDEC mode bits to i855 |
| if (command == RAM_COMMAND_MRS || command == RAM_COMMAND_EMRS) { |
| /* Host address lines [13:3] map to DIMM address lines [11, 9:0] */ |
| i855_mode_bits = ((jedec_mode_bits & 0x800) << (13 - 11)) | ((jedec_mode_bits & 0x3ff) << (12 - 9)); |
| } |
| |
| for (i = 0; i < (DIMM_SOCKETS * 2); ++i) { |
| uint8_t dimm_end_32M_multiple = pci_read_config8(NORTHBRIDGE_MMC, DRB + i); |
| if (dimm_end_32M_multiple > dimm_start_32M_multiple) { |
| |
| uint32_t dimm_start_address = dimm_start_32M_multiple << 25; |
| PRINTK_DEBUG(" Sending RAM command to 0x%08x\n", dimm_start_address + i855_mode_bits); |
| read32(dimm_start_address + i855_mode_bits); |
| |
| // Set the start of the next DIMM |
| dimm_start_32M_multiple = dimm_end_32M_multiple; |
| } |
| } |
| } |
| } |
| |
| static void set_initialize_complete(void) |
| { |
| uint32_t drc_reg; |
| |
| drc_reg = pci_read_config32(NORTHBRIDGE_MMC, DRC); |
| drc_reg |= (1 << 29); |
| pci_write_config32(NORTHBRIDGE_MMC, DRC, drc_reg); |
| } |
| |
| static void sdram_enable(void) |
| { |
| int i; |
| |
| print_debug("Ram enable 1\n"); |
| delay(); |
| delay(); |
| |
| /* NOP command */ |
| PRINTK_DEBUG(" NOP\n"); |
| do_ram_command(RAM_COMMAND_NOP, 0); |
| delay(); |
| delay(); |
| delay(); |
| |
| /* Pre-charge all banks (at least 200 us after NOP) */ |
| PRINTK_DEBUG(" Pre-charging all banks\n"); |
| do_ram_command(RAM_COMMAND_PRECHARGE, 0); |
| delay(); |
| delay(); |
| delay(); |
| |
| print_debug("Ram enable 4\n"); |
| do_ram_command(RAM_COMMAND_EMRS, SDRAM_EXTMODE_DLL_ENABLE); |
| delay(); |
| delay(); |
| delay(); |
| |
| print_debug("Ram enable 5\n"); |
| do_ram_command(RAM_COMMAND_MRS, VG85X_MODE | SDRAM_MODE_DLL_RESET); |
| |
| print_debug("Ram enable 6\n"); |
| do_ram_command(RAM_COMMAND_PRECHARGE, 0); |
| delay(); |
| delay(); |
| delay(); |
| |
| /* 8 CBR refreshes (Auto Refresh) */ |
| PRINTK_DEBUG(" 8 CBR refreshes\n"); |
| for(i = 0; i < 8; i++) { |
| do_ram_command(RAM_COMMAND_CBR, 0); |
| delay(); |
| delay(); |
| delay(); |
| } |
| |
| print_debug("Ram enable 8\n"); |
| do_ram_command(RAM_COMMAND_MRS, VG85X_MODE | SDRAM_MODE_NORMAL); |
| |
| /* Set GME-M Mode Select bits back to NORMAL operation mode */ |
| PRINTK_DEBUG(" Normal operation mode\n"); |
| do_ram_command(RAM_COMMAND_NORMAL, 0); |
| delay(); |
| delay(); |
| delay(); |
| |
| print_debug("Ram enable 9\n"); |
| set_initialize_complete(); |
| |
| delay(); |
| delay(); |
| delay(); |
| delay(); |
| delay(); |
| |
| print_debug("After configuration:\n"); |
| /* dump_pci_devices(); */ |
| |
| /* |
| print_debug("\n\n***** RAM TEST *****\n"); |
| ram_check(0, 0xa0000); |
| ram_check(0x100000, 0x40000000); |
| */ |
| } |
| |
| /*----------------------------------------------------------------------------- |
| DIMM-independant configuration functions: |
| -----------------------------------------------------------------------------*/ |
| |
| /** |
| * Set only what I need until it works, then make it figure things out on boot |
| * assumes only one DIMM is populated. |
| */ |
| static void sdram_set_registers(void) |
| { |
| /* |
| print_debug("Before configuration:\n"); |
| dump_pci_devices(); |
| */ |
| } |
| |
| static void spd_set_row_attributes(uint8_t dimm_mask) |
| { |
| int i; |
| uint16_t row_attributes = 0; |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| u8 dimm = DIMM0 + i; |
| struct dimm_size page_size; |
| struct dimm_size sdram_width; |
| |
| if (!(dimm_mask & (1 << i))) { |
| row_attributes |= 0x77 << (i << 3); |
| continue; // This DIMM not usable |
| } |
| |
| // Get the relevant parameters via SPD |
| page_size = sdram_spd_get_page_size(dimm); |
| sdram_width = sdram_spd_get_width(dimm); |
| |
| // Update the DRAM Row Attributes. |
| // Page size is encoded as log2(page size in bits) - log2(2 KB) or 4 KB == 1, 8 KB == 3, 16KB == 3 |
| // NOTE: 2 KB = 16 Kb = 2^14 |
| row_attributes |= (page_size.side1 - 14) << (i << 3); // Side 1 of each DIMM is an EVEN row |
| |
| if (sdram_width.side2 > 0) |
| row_attributes |= (page_size.side2 - 14) << ((i << 3) + 4); // Side 2 is ODD |
| else |
| row_attributes |= 7 << ((i << 3) + 4); |
| /* go to the next DIMM */ |
| } |
| |
| PRINTK_DEBUG("DRA: %04x\n", row_attributes); |
| |
| /* Write the new row attributes register */ |
| pci_write_config16(NORTHBRIDGE_MMC, DRA, row_attributes); |
| } |
| |
| static void spd_set_dram_controller_mode(uint8_t dimm_mask) |
| { |
| int i; |
| |
| // Initial settings |
| u32 controller_mode = pci_read_config32(NORTHBRIDGE_MMC, DRC); |
| u32 system_refresh_mode = (controller_mode >> 7) & 7; |
| |
| controller_mode |= (1 << 20); // ECC |
| controller_mode |= (1 << 15); // RAS lockout |
| controller_mode |= (1 << 12); // Address Tri-state enable (ADRTRIEN), FIXME: how is this detected????? |
| controller_mode |= (2 << 10); // FIXME: Undocumented, really needed????? |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| u8 dimm = DIMM0 + i; |
| uint32_t dimm_refresh_mode; |
| int value; |
| u8 tRCD, tRP; |
| |
| if (!(dimm_mask & (1 << i))) { |
| continue; // This DIMM not usable |
| } |
| |
| // Disable ECC mode if any one of the DIMMs does not support ECC |
| value = spd_read_byte(dimm, SPD_DIMM_CONFIG_TYPE); |
| die_on_spd_error(value); |
| if (value != ERROR_SCHEME_ECC) |
| controller_mode &= ~(3 << 20); |
| |
| value = spd_read_byte(dimm, SPD_REFRESH); |
| die_on_spd_error(value); |
| value &= 0x7f; // Mask off self-refresh bit |
| if (value > MAX_SPD_REFRESH_RATE) { |
| print_err("unsupported refresh rate\n"); |
| continue; |
| } |
| // Get the appropriate i855 refresh mode for this DIMM |
| dimm_refresh_mode = refresh_rate_map[value]; |
| if (dimm_refresh_mode > 7) { |
| print_err("unsupported refresh rate\n"); |
| continue; |
| } |
| // If this DIMM requires more frequent refresh than others, |
| // update the system setting |
| if (refresh_frequency[dimm_refresh_mode] > |
| refresh_frequency[system_refresh_mode]) |
| system_refresh_mode = dimm_refresh_mode; |
| |
| /* FIXME: is this correct? */ |
| tRCD = spd_read_byte(dimm, SPD_tRCD); |
| tRP = spd_read_byte(dimm, SPD_tRP); |
| if (tRCD != tRP) { |
| PRINTK_DEBUG(" Disabling RAS lockouk due to tRCD (%d) != tRP (%d)\n", tRCD, tRP); |
| controller_mode &= ~(1 << 15); |
| } |
| |
| /* go to the next DIMM */ |
| } |
| |
| controller_mode &= ~(7 << 7); |
| controller_mode |= (system_refresh_mode << 7); |
| PRINTK_DEBUG("DRC: %08x\n", controller_mode); |
| |
| pci_write_config32(NORTHBRIDGE_MMC, DRC, controller_mode); |
| } |
| |
| static void spd_set_dram_timing(uint8_t dimm_mask) |
| { |
| int i; |
| u32 dram_timing; |
| |
| // CAS# latency bitmasks in SPD_ACCEPTABLE_CAS_LATENCIES format |
| // NOTE: i82822 supports only 2.0 and 2.5 |
| uint32_t system_compatible_cas_latencies = SPD_CAS_LATENCY_2_0 | SPD_CAS_LATENCY_2_5; |
| uint8_t slowest_row_precharge = 0; |
| uint8_t slowest_ras_cas_delay = 0; |
| uint8_t slowest_active_to_precharge_delay = 0; |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| u8 dimm = DIMM0 + i; |
| int value; |
| uint32_t current_cas_latency; |
| uint32_t dimm_compatible_cas_latencies; |
| if (!(dimm_mask & (1 << i))) |
| continue; // This DIMM not usable |
| |
| value = spd_read_byte(dimm, SPD_ACCEPTABLE_CAS_LATENCIES); |
| PRINTK_DEBUG("SPD_ACCEPTABLE_CAS_LATENCIES: %d\n", value); |
| die_on_spd_error(value); |
| |
| dimm_compatible_cas_latencies = value & 0x7f; // Start with all supported by DIMM |
| PRINTK_DEBUG("dimm_compatible_cas_latencies #1: %d\n", dimm_compatible_cas_latencies); |
| |
| current_cas_latency = 1 << log2(dimm_compatible_cas_latencies); // Max supported by DIMM |
| PRINTK_DEBUG("current_cas_latency: %d\n", current_cas_latency); |
| |
| // Can we support the highest CAS# latency? |
| value = spd_read_byte(dimm, SPD_MIN_CYCLE_TIME_AT_CAS_MAX); |
| die_on_spd_error(value); |
| PRINTK_DEBUG("SPD_MIN_CYCLE_TIME_AT_CAS_MAX: %d.%d\n", value >> 4, value & 0xf); |
| |
| // NOTE: At 133 MHz, 1 clock == 7.52 ns |
| if (value > 0x75) { |
| // Our bus is too fast for this CAS# latency |
| // Remove it from the bitmask of those supported by the DIMM that are compatible |
| dimm_compatible_cas_latencies &= ~current_cas_latency; |
| PRINTK_DEBUG("dimm_compatible_cas_latencies #2: %d\n", dimm_compatible_cas_latencies); |
| } |
| // Can we support the next-highest CAS# latency (max - 0.5)? |
| |
| current_cas_latency >>= 1; |
| if (current_cas_latency != 0) { |
| value = spd_read_byte(dimm, SPD_SDRAM_CYCLE_TIME_2ND); |
| die_on_spd_error(value); |
| PRINTK_DEBUG("SPD_SDRAM_CYCLE_TIME_2ND: %d.%d\n", value >> 4, value & 0xf); |
| if (value > 0x75) { |
| dimm_compatible_cas_latencies &= ~current_cas_latency; |
| PRINTK_DEBUG("dimm_compatible_cas_latencies #2: %d\n", dimm_compatible_cas_latencies); |
| } |
| } |
| // Can we support the next-highest CAS# latency (max - 1.0)? |
| current_cas_latency >>= 1; |
| if (current_cas_latency != 0) { |
| value = spd_read_byte(dimm, SPD_SDRAM_CYCLE_TIME_3RD); |
| PRINTK_DEBUG("SPD_SDRAM_CYCLE_TIME_3RD: %d.%d\n", value >> 4, value & 0xf); |
| die_on_spd_error(value); |
| if (value > 0x75) { |
| dimm_compatible_cas_latencies &= ~current_cas_latency; |
| PRINTK_DEBUG("dimm_compatible_cas_latencies #2: %d\n", dimm_compatible_cas_latencies); |
| } |
| } |
| // Restrict the system to CAS# latencies compatible with this DIMM |
| system_compatible_cas_latencies &= dimm_compatible_cas_latencies; |
| |
| value = spd_read_byte(dimm, SPD_MIN_ROW_PRECHARGE_TIME); |
| die_on_spd_error(value); |
| if (value > slowest_row_precharge) |
| slowest_row_precharge = value; |
| |
| value = spd_read_byte(dimm, SPD_MIN_RAS_TO_CAS_DELAY); |
| die_on_spd_error(value); |
| if (value > slowest_ras_cas_delay) |
| slowest_ras_cas_delay = value; |
| |
| value = spd_read_byte(dimm, SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY); |
| die_on_spd_error(value); |
| if (value > slowest_active_to_precharge_delay) |
| slowest_active_to_precharge_delay = value; |
| |
| /* go to the next DIMM */ |
| } |
| PRINTK_DEBUG("CAS latency: %d\n", system_compatible_cas_latencies); |
| |
| dram_timing = pci_read_config32(NORTHBRIDGE_MMC, DRT); |
| dram_timing &= ~(DRT_CAS_MASK | DRT_TRP_MASK | DRT_RCD_MASK); |
| PRINTK_DEBUG("DRT: %08x\n", dram_timing); |
| |
| if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) { |
| dram_timing |= DRT_CAS_2_0; |
| } else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) { |
| dram_timing |= DRT_CAS_2_5; |
| } else |
| die("No CAS# latencies compatible with all DIMMs!!\n"); |
| |
| uint32_t current_cas_latency = dram_timing & DRT_CAS_MASK; |
| |
| /* tRP */ |
| |
| PRINTK_DEBUG("slowest_row_precharge: %d.%d\n", slowest_row_precharge >> 2, slowest_row_precharge & 0x3); |
| // i855 supports only 2, 3 or 4 clocks for tRP |
| if (slowest_row_precharge > ((30 << 2))) |
| die("unsupported DIMM tRP"); // > 30.0 ns: 5 or more clocks |
| else if (slowest_row_precharge > ((22 << 2) | (2 << 0))) |
| dram_timing |= DRT_TRP_4; // > 22.5 ns: 4 or more clocks |
| else if (slowest_row_precharge > (15 << 2)) |
| dram_timing |= DRT_TRP_3; // > 15.0 ns: 3 clocks |
| else |
| dram_timing |= DRT_TRP_2; // <= 15.0 ns: 2 clocks |
| |
| /* tRCD */ |
| |
| PRINTK_DEBUG("slowest_ras_cas_delay: %d.%d\n", slowest_ras_cas_delay >> 2, slowest_ras_cas_delay & 0x3); |
| // i855 supports only 2, 3 or 4 clocks for tRCD |
| if (slowest_ras_cas_delay > ((30 << 2))) |
| die("unsupported DIMM tRCD"); // > 30.0 ns: 5 or more clocks |
| else if (slowest_ras_cas_delay > ((22 << 2) | (2 << 0))) |
| dram_timing |= DRT_RCD_4; // > 22.5 ns: 4 or more clocks |
| else if (slowest_ras_cas_delay > (15 << 2)) |
| dram_timing |= DRT_RCD_3; // > 15.0 ns: 3 clocks |
| else |
| dram_timing |= DRT_RCD_2; // <= 15.0 ns: 2 clocks |
| |
| /* tRAS, min */ |
| |
| PRINTK_DEBUG("slowest_active_to_precharge_delay: %d\n", slowest_active_to_precharge_delay); |
| // i855 supports only 5, 6, 7 or 8 clocks for tRAS |
| // 5 clocks ~= 37.6 ns, 6 clocks ~= 45.1 ns, 7 clocks ~= 52.6 ns, 8 clocks ~= 60.1 ns |
| if (slowest_active_to_precharge_delay > 60) |
| die("unsupported DIMM tRAS"); // > 52 ns: 8 or more clocks |
| else if (slowest_active_to_precharge_delay > 52) |
| dram_timing |= DRT_TRAS_MIN_8; // 46-52 ns: 7 clocks |
| else if (slowest_active_to_precharge_delay > 45) |
| dram_timing |= DRT_TRAS_MIN_7; // 46-52 ns: 7 clocks |
| else if (slowest_active_to_precharge_delay > 37) |
| dram_timing |= DRT_TRAS_MIN_6; // 38-45 ns: 6 clocks |
| else |
| dram_timing |= DRT_TRAS_MIN_5; // < 38 ns: 5 clocks |
| |
| /* FIXME: guess work starts here... |
| * |
| * Intel refers to DQ turn-arround values for back to calculate the values, |
| * but i have no idea what this means |
| */ |
| |
| /* |
| * Back to Back Read-Write command spacing (DDR, different Rows/Bank) |
| */ |
| /* Set to a 3 clock back to back read to write turn around. |
| * 2 is a good delay if the CAS latency is 2.0 */ |
| dram_timing &= ~(3 << 28); |
| if (current_cas_latency == DRT_CAS_2_0) |
| dram_timing |= (2 << 28); // 2 clocks |
| else |
| dram_timing |= (1 << 28); // 3 clocks |
| |
| /* |
| * Back to Back Read-Write command spacing (DDR, same or different Rows/Bank) |
| */ |
| dram_timing &= ~(3 << 26); |
| if (current_cas_latency == DRT_CAS_2_0) |
| dram_timing |= (2 << 26); // 5 clocks |
| else |
| dram_timing |= (1 << 26); // 6 clocks |
| |
| /* |
| * Back To Back Read-Read commands spacing (DDR, different Rows): |
| */ |
| dram_timing &= ~(1 << 25); |
| dram_timing |= (1 << 25); // 3 clocks |
| |
| PRINTK_DEBUG("DRT: %08x\n", dram_timing); |
| pci_write_config32(NORTHBRIDGE_MMC, DRT, dram_timing); |
| } |
| |
| static void spd_set_dram_size(uint8_t dimm_mask) |
| { |
| int i; |
| int total_dram = 0; |
| uint32_t drb_reg = 0; |
| |
| for (i = 0; i < DIMM_SOCKETS; i++) { |
| u8 dimm = DIMM0 + i; |
| struct dimm_size sz; |
| |
| if (!(dimm_mask & (1 << i))) { |
| /* fill values even for not present DIMMs */ |
| drb_reg |= (total_dram << (i * 16)); |
| drb_reg |= (total_dram << ((i * 16) + 8)); |
| |
| continue; // This DIMM not usable |
| } |
| sz = spd_get_dimm_size(dimm); |
| |
| total_dram += (1 << (sz.side1 - 28)); |
| drb_reg |= (total_dram << (i * 16)); |
| |
| total_dram += (1 << (sz.side2 - 28)); |
| drb_reg |= (total_dram << ((i * 16) + 8)); |
| } |
| PRINTK_DEBUG("DRB: %08x\n", drb_reg); |
| pci_write_config32(NORTHBRIDGE_MMC, DRB, drb_reg); |
| } |
| |
| |
| static void spd_set_dram_pwr_management(void) |
| { |
| uint32_t pwrmg_reg; |
| |
| pwrmg_reg = 0x10f10430; |
| pci_write_config32(NORTHBRIDGE_MMC, PWRMG, pwrmg_reg); |
| } |
| |
| static void spd_set_dram_throttle_control(void) |
| { |
| uint32_t dtc_reg = 0; |
| |
| /* DDR SDRAM Throttle Mode (TMODE): |
| * 0011 = Both Rank and GMCH Thermal Sensor based throttling is enabled. When the external SO- |
| * DIMM Thermal Sensor is Tripped DDR SDRAM Throttling begins based on the setting in RTT |
| */ |
| dtc_reg |= (3 << 28); |
| |
| /* Read Counter Based Power Throttle Control (RCTC): |
| * 0 = 85% |
| */ |
| dtc_reg |= (0 << 24); |
| |
| /* Write Counter Based Power Throttle Control (WCTC): |
| * 0 = 85% |
| */ |
| dtc_reg |= (0 << 20); |
| |
| /* Read Thermal Based Power Throttle Control (RTTC): |
| * 0xA = 20% |
| */ |
| dtc_reg |= (0xA << 16); |
| |
| /* Write Thermal Based Power Throttle Control (WTTC): |
| * 0xA = 20% |
| */ |
| dtc_reg |= (0xA << 12); |
| |
| /* Counter Based Throttle Lock (CTLOCK): */ |
| dtc_reg |= (0 << 11); |
| |
| /* Thermal Throttle Lock (TTLOCK): */ |
| dtc_reg |= (0 << 10); |
| |
| /* Thermal Power Throttle Control fields Enable: */ |
| dtc_reg |= (1 << 9); |
| |
| /* High Priority Stream Throttling Enable: */ |
| dtc_reg |= (0 << 8); |
| |
| /* Global DDR SDRAM Sampling Window (GDSW): */ |
| dtc_reg |= 0xff; |
| PRINTK_DEBUG("DTC: %08x\n", dtc_reg); |
| pci_write_config32(NORTHBRIDGE_MMC, DTC, dtc_reg); |
| } |
| |
| static void spd_update(u8 reg, u32 new_value) |
| { |
| #if CONFIG_DEBUG_RAM_SETUP |
| u32 value1 = pci_read_config32(NORTHBRIDGE_MMC, reg); |
| #endif |
| pci_write_config32(NORTHBRIDGE_MMC, reg, new_value); |
| #if CONFIG_DEBUG_RAM_SETUP |
| u32 value2 = pci_read_config32(NORTHBRIDGE_MMC, reg); |
| PRINTK_DEBUG("update reg %02x, old: %08x, new: %08x, read back: %08x\n", reg, value1, new_value, value2); |
| #endif |
| } |
| |
| /* if ram still doesn't work do this function */ |
| static void spd_set_undocumented_registers(void) |
| { |
| spd_update(0x74, 0x00000001); |
| spd_update(0x78, 0x001fe974); |
| spd_update(0x80, 0x00af0039); |
| spd_update(0x84, 0x0000033c); |
| spd_update(0x88, 0x00000010); |
| |
| spd_update(0xc0, 0x00000003); |
| } |
| |
| static void northbridge_set_registers(void) |
| { |
| u16 value; |
| int video_memory = 0; |
| |
| printk(BIOS_DEBUG, "Setting initial Northbridge registers....\n"); |
| |
| /* Set the value for Fixed DRAM Hole Control Register */ |
| pci_write_config8(NORTHBRIDGE, FDHC, 0x00); |
| |
| /* Set the value for Programable Attribute Map Registers |
| * Ideally, this should be R/W for as many ranges as possible. |
| */ |
| pci_write_config8(NORTHBRIDGE, PAM0, 0x30); |
| pci_write_config8(NORTHBRIDGE, PAM1, 0x33); |
| pci_write_config8(NORTHBRIDGE, PAM2, 0x33); |
| pci_write_config8(NORTHBRIDGE, PAM3, 0x33); |
| pci_write_config8(NORTHBRIDGE, PAM4, 0x33); |
| pci_write_config8(NORTHBRIDGE, PAM5, 0x33); |
| pci_write_config8(NORTHBRIDGE, PAM6, 0x33); |
| |
| /* Set the value for System Management RAM Control Register */ |
| pci_write_config8(NORTHBRIDGE, SMRAM, 0x02); |
| |
| /* Set the value for GMCH Control Register #1 */ |
| switch (CONFIG_VIDEO_MB) { |
| case 1: /* 1M of memory */ |
| video_memory = 0x1; |
| break; |
| case 4: /* 4M of memory */ |
| video_memory = 0x2; |
| break; |
| case 8: /* 8M of memory */ |
| video_memory = 0x3; |
| break; |
| case 16: /* 16M of memory */ |
| video_memory = 0x4; |
| break; |
| case 32: /* 32M of memory */ |
| video_memory = 0x5; |
| break; |
| default: /* No memory */ |
| pci_write_config16(NORTHBRIDGE, GMC, pci_read_config16(NORTHBRIDGE, GMC) | 1); |
| video_memory = 0x0; |
| } |
| |
| value = pci_read_config16(NORTHBRIDGE, GGC); |
| value |= video_memory << 4; |
| if (video_memory == 0) { |
| value &= ~(1 < 1); |
| } else |
| value |= (1 < 1); |
| pci_write_config16(NORTHBRIDGE, GGC, value); |
| |
| /* AGPCMD: disable AGP, Data-Rate: 1x */ |
| pci_write_config32(NORTHBRIDGE, AGPCMD, 0x00000001); |
| |
| pci_write_config8(NORTHBRIDGE, AMTT, 0x20); |
| pci_write_config8(NORTHBRIDGE, LPTT, 0x10); |
| |
| printk(BIOS_DEBUG, "Initial Northbridge registers have been set.\n"); |
| } |
| |
| static void sdram_set_spd_registers(void) |
| { |
| uint8_t dimm_mask; |
| |
| PRINTK_DEBUG("Reading SPD data...\n"); |
| |
| dimm_mask = spd_get_supported_dimms(); |
| |
| if (dimm_mask == 0) { |
| print_debug("No usable memory for this controller\n"); |
| } else { |
| PRINTK_DEBUG("DIMM MASK: %02x\n", dimm_mask); |
| |
| spd_set_row_attributes(dimm_mask); |
| spd_set_dram_controller_mode(dimm_mask); |
| spd_set_dram_timing(dimm_mask); |
| spd_set_dram_size(dimm_mask); |
| spd_set_dram_pwr_management(); |
| spd_set_dram_throttle_control(); |
| spd_set_undocumented_registers(); |
| } |
| |
| /* Setup Initial Northbridge Registers */ |
| northbridge_set_registers(); |
| } |
| |