/*
 * This file is part of the flashrom project.
 *
 * Copyright (C) 2008 Wang Qingpei <Qingpei.Wang@amd.com>
 * Copyright (C) 2008 Joe Bao <Zheng.Bao@amd.com>
 * Copyright (C) 2008 Advanced Micro Devices, Inc.
 * Copyright (C) 2009, 2010, 2013 Carl-Daniel Hailfinger
 * Copyright (C) 2013 Stefan Tauner
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 */

#if defined(__i386__) || defined(__x86_64__)

#include <string.h>
#include <stdlib.h>
#include "flash.h"
#include <stdbool.h>
#include "programmer.h"
#include "hwaccess.h"
#include "spi.h"

/* This struct is unused, but helps visualize the SB600 SPI BAR layout.
 *struct sb600_spi_controller {
 *	unsigned int spi_cntrl0;	/ * 00h * /
 *	unsigned int restrictedcmd1;	/ * 04h * /
 *	unsigned int restrictedcmd2;	/ * 08h * /
 *	unsigned int spi_cntrl1;	/ * 0ch * /
 *	unsigned int spi_cmdvalue0;	/ * 10h * /
 *	unsigned int spi_cmdvalue1;	/ * 14h * /
 *	unsigned int spi_cmdvalue2;	/ * 18h * /
 *	unsigned int spi_fakeid;	/ * 1Ch * /
 *};
 */

static uint8_t *sb600_spibar = NULL;
enum amd_chipset {
	CHIPSET_AMD_UNKNOWN,
	CHIPSET_SB6XX,
	CHIPSET_SB7XX, /* SP5100 too */
	CHIPSET_SB89XX, /* Hudson-1 too */
	CHIPSET_HUDSON234,
	CHIPSET_BOLTON,
	CHIPSET_YANGTZE,
	CHIPSET_PROMONTORY,
};
static enum amd_chipset amd_gen = CHIPSET_AMD_UNKNOWN;

#define FIFO_SIZE_OLD		8
#define FIFO_SIZE_YANGTZE	71

#define PM_INDEX		0xCD6
#define PM_DATA			0xCD7
#define ISA_CONTROL		0x04
#define MMIO_EN			0x02
#define ACPI_MMIO_BASE		0xFED80000
#define MISC_BASE		0xE00
#define STRAP_STATUS		0x80
#define EC_ENABLE_STRAP		0x04

static int sb600_spi_send_command(const struct flashctx *flash, unsigned int writecnt, unsigned int readcnt,
				  const unsigned char *writearr, unsigned char *readarr);
static int spi100_spi_send_command(const struct flashctx *flash, unsigned int writecnt, unsigned int readcnt,
				  const unsigned char *writearr, unsigned char *readarr);

static struct spi_master spi_master_sb600 = {
	.type = SPI_CONTROLLER_SB600,
	.max_data_read = FIFO_SIZE_OLD,
	.max_data_write = FIFO_SIZE_OLD - 3,
	.command = sb600_spi_send_command,
	.multicommand = default_spi_send_multicommand,
	.read = default_spi_read,
	.write_256 = default_spi_write_256,
};

static struct spi_master spi_master_yangtze = {
	.type = SPI_CONTROLLER_YANGTZE,
	.max_data_read = FIFO_SIZE_YANGTZE - 3, /* Apparently the big SPI 100 buffer is not a ring buffer. */
	.max_data_write = FIFO_SIZE_YANGTZE - 3,
	.command = spi100_spi_send_command,
	.multicommand = default_spi_send_multicommand,
	.read = read_memmapped,
	.write_256 = default_spi_write_256,
};

static uint8_t pm_ioread (uint8_t addr)
{
	OUTB(addr, PM_INDEX);
	return INB(PM_DATA);
}

static int find_smbus (struct pci_dev **smbus_dev, uint16_t vendor, uint16_t device)
{
       *smbus_dev = pci_dev_find(vendor, device);
       if (*smbus_dev == NULL) {
               msg_pdbg("No SMBus device with ID %04X:%04X found.\n", vendor, device);
               msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
               return 1;
       }
       return 0;
}

/* Determine the chipset's version and identify the respective SMBUS device. */
static int determine_generation(struct pci_dev *dev, struct pci_dev **smbus_dev)
{
	amd_gen = CHIPSET_AMD_UNKNOWN;
	msg_pdbg2("Trying to determine the generation of the SPI interface... ");
	if (dev->device_id == 0x438d) {
		amd_gen = CHIPSET_SB6XX;
		msg_pdbg("SB6xx detected.\n");
	} else if (dev->device_id == 0x439d) {
		if (find_smbus(smbus_dev, 0x1002, 0x4385) != 0)
			return 1;
		uint8_t rev = pci_read_byte(*smbus_dev, PCI_REVISION_ID);
		if (rev >= 0x39 && rev <= 0x3D) {
			amd_gen = CHIPSET_SB7XX;
			msg_pdbg("SB7xx/SP5100 detected.\n");
		} else if (rev >= 0x40 && rev <= 0x42) {
			amd_gen = CHIPSET_SB89XX;
			msg_pdbg("SB8xx/SB9xx/Hudson-1 detected.\n");
		} else {
			msg_pwarn("SB device found but SMBus revision 0x%02x does not match known values.\n"
				  "Assuming SB8xx/SB9xx/Hudson-1. Please send a log to flashrom@flashrom.org\n",
				   rev);
			amd_gen = CHIPSET_SB89XX;
		}
	} else if (dev->device_id == 0x780e) {
		/* The PCI ID of the LPC bridge doesn't change between Hudson-2/3/4 and Yangtze (Kabini/Temash)
		 * although they use different SPI interfaces. */
		if (find_smbus(smbus_dev, 0x1022, 0x780b) != 0)
			return 1;
		uint8_t rev = pci_read_byte(*smbus_dev, PCI_REVISION_ID);

		if (rev >= 0x11 && rev <= 0x15) {
			amd_gen = CHIPSET_HUDSON234;
			msg_pdbg("Hudson-2/3/4 detected.\n");
		} else if (rev == 0x16) {
			amd_gen = CHIPSET_BOLTON;
			msg_pdbg("Bolton detected.\n");
		} else if ((rev >= 0x39 && rev <= 0x3A) || rev == 0x42) {
			amd_gen = CHIPSET_YANGTZE;
			msg_pdbg("Yangtze detected.\n");
		} else {
			msg_pwarn("FCH device found but SMBus revision 0x%02x does not match known values.\n"
				  "Please report this to flashrom@flashrom.org and include this log and\n"
				  "the output of lspci -nnvx, thanks!.\n", rev);
		}
	} else if (dev->device_id == 0x790e) {
		if (find_smbus(smbus_dev, 0x1022, 0x790b) != 0)
			return 1;
		amd_gen = CHIPSET_PROMONTORY;
		msg_pdbg("Promontory detected.\n");
	} else
		msg_pwarn("%s: Unknown LPC device %x :%x.\n"
			  "Please report this to flashrom@flashrom.org and include this log and\n"
			  "the output of lspci -nnvx, thanks!\n",
			  __func__, dev->vendor_id, dev->device_id);

	if (amd_gen == CHIPSET_AMD_UNKNOWN) {
		msg_perr("Could not determine chipset generation.");
		return 1;
	}
	return 0;
}

static void reset_internal_fifo_pointer(void)
{
	mmio_writeb(mmio_readb(sb600_spibar + 2) | 0x10, sb600_spibar + 2);

	/* FIXME: This loop needs a timeout and a clearer message. */
	while (mmio_readb(sb600_spibar + 0xD) & 0x7)
		msg_pspew("reset\n");
}

static int compare_internal_fifo_pointer(uint8_t want)
{
	uint8_t have = mmio_readb(sb600_spibar + 0xd) & 0x07;
	want %= FIFO_SIZE_OLD;
	if (have != want) {
		msg_perr("AMD SPI FIFO pointer corruption! Pointer is %d, wanted %d\n", have, want);
		msg_perr("Something else is accessing the flash chip and causes random corruption.\n"
			 "Please stop all applications and drivers and IPMI which access the flash chip.\n");
		return 1;
	} else {
		msg_pspew("AMD SPI FIFO pointer is %d, wanted %d\n", have, want);
		return 0;
	}
}

/* Check the number of bytes to be transmitted and extract opcode. */
static int check_readwritecnt(const struct flashctx *flash, unsigned int writecnt, unsigned int readcnt)
{
	unsigned int maxwritecnt = (amd_gen < CHIPSET_YANGTZE)? FIFO_SIZE_OLD:FIFO_SIZE_YANGTZE;
	if (writecnt > maxwritecnt) {
		msg_pinfo("%s: SPI controller can not send %d bytes, it is limited to %d bytes\n",
			  __func__, writecnt, maxwritecnt);
		return SPI_INVALID_LENGTH;
	}

	unsigned int maxreadcnt = (amd_gen < CHIPSET_YANGTZE)? FIFO_SIZE_OLD:FIFO_SIZE_YANGTZE;
	if (readcnt > maxreadcnt) {
		msg_pinfo("%s: SPI controller can not receive %d bytes, it is limited to %d bytes\n",
			  __func__, readcnt, maxreadcnt);
		return SPI_INVALID_LENGTH;
	}
	return 0;
}

static void execute_command(void)
{
	msg_pspew("Executing... ");
	mmio_writeb(mmio_readb(sb600_spibar + 2) | 1, sb600_spibar + 2);
	while (mmio_readb(sb600_spibar + 2) & 1)
		;
	msg_pspew("done\n");
}

static int sb600_spi_send_command(const struct flashctx *flash, unsigned int writecnt,
				  unsigned int readcnt,
				  const unsigned char *writearr,
				  unsigned char *readarr)
{
	/* First byte is cmd which can not be sent through the FIFO. */
	unsigned char cmd = *writearr++;
	writecnt--;
	msg_pspew("%s, cmd=0x%02x, writecnt=%d, readcnt=%d\n", __func__, cmd, writecnt, readcnt);
	mmio_writeb(cmd, sb600_spibar + 0);

	int ret = check_readwritecnt(flash, writecnt, readcnt);
	if (ret != 0)
		return ret;

	/* This is a workaround for a bug in SPI controller. If we only send
	 * an opcode and no additional data/address, the SPI controller will
	 * read one byte too few from the chip. Basically, the last byte of
	 * the chip response is discarded and will not end up in the FIFO.
	 * It is unclear if the CS# line is set high too early as well.
	 */
	unsigned int readoffby1 = (writecnt > 0) ? 0 : 1;
	uint8_t readwrite = (readcnt + readoffby1) << 4 | (writecnt);
	mmio_writeb(readwrite, sb600_spibar + 1);

	reset_internal_fifo_pointer();
	msg_pspew("Filling FIFO: ");
	int count;
	for (count = 0; count < writecnt; count++) {
		msg_pspew("[%02x]", writearr[count]);
		mmio_writeb(writearr[count], sb600_spibar + 0xC);
	}
	msg_pspew("\n");
	if (compare_internal_fifo_pointer(writecnt))
		return SPI_PROGRAMMER_ERROR;

	/*
	 * We should send the data in sequence, which means we need to reset
	 * the FIFO pointer to the first byte we want to send.
	 */
	reset_internal_fifo_pointer();
	execute_command();
	if (compare_internal_fifo_pointer(writecnt + readcnt))
		return SPI_PROGRAMMER_ERROR;

	/*
	 * After the command executed, we should find out the index of the
	 * received byte. Here we just reset the FIFO pointer and skip the
	 * writecnt.
	 * It would be possible to increase the FIFO pointer by one instead
	 * of reading and discarding one byte from the FIFO.
	 * The FIFO is implemented on top of an 8 byte ring buffer and the
	 * buffer is never cleared. For every byte that is shifted out after
	 * the opcode, the FIFO already stores the response from the chip.
	 * Usually, the chip will respond with 0x00 or 0xff.
	 */
	reset_internal_fifo_pointer();

	/* Skip the bytes we sent. */
	msg_pspew("Skipping: ");
	for (count = 0; count < writecnt; count++) {
		msg_pspew("[%02x]", mmio_readb(sb600_spibar + 0xC));
	}
	msg_pspew("\n");
	if (compare_internal_fifo_pointer(writecnt))
		return SPI_PROGRAMMER_ERROR;

	msg_pspew("Reading FIFO: ");
	for (count = 0; count < readcnt; count++) {
		readarr[count] = mmio_readb(sb600_spibar + 0xC);
		msg_pspew("[%02x]", readarr[count]);
	}
	msg_pspew("\n");
	if (compare_internal_fifo_pointer(writecnt+readcnt))
		return SPI_PROGRAMMER_ERROR;

	if (mmio_readb(sb600_spibar + 1) != readwrite) {
		msg_perr("Unexpected change in AMD SPI read/write count!\n");
		msg_perr("Something else is accessing the flash chip and causes random corruption.\n"
			 "Please stop all applications and drivers and IPMI which access the flash chip.\n");
		return SPI_PROGRAMMER_ERROR;
	}

	return 0;
}

static int spi100_spi_send_command(const struct flashctx *flash, unsigned int writecnt,
				  unsigned int readcnt,
				  const unsigned char *writearr,
				  unsigned char *readarr)
{
	/* First byte is cmd which can not be sent through the buffer. */
	unsigned char cmd = *writearr++;
	writecnt--;
	msg_pspew("%s, cmd=0x%02x, writecnt=%d, readcnt=%d\n", __func__, cmd, writecnt, readcnt);
	mmio_writeb(cmd, sb600_spibar + 0);

	int ret = check_readwritecnt(flash, writecnt, readcnt);
	if (ret != 0)
		return ret;

	/* Use the extended TxByteCount and RxByteCount registers. */
	mmio_writeb(writecnt, sb600_spibar + 0x48);
	mmio_writeb(readcnt, sb600_spibar + 0x4b);

	msg_pspew("Filling buffer: ");
	int count;
	for (count = 0; count < writecnt; count++) {
		msg_pspew("[%02x]", writearr[count]);
		mmio_writeb(writearr[count], sb600_spibar + 0x80 + count);
	}
	msg_pspew("\n");

	execute_command();

	msg_pspew("Reading buffer: ");
	for (count = 0; count < readcnt; count++) {
		readarr[count] = mmio_readb(sb600_spibar + 0x80 + (writecnt + count) % FIFO_SIZE_YANGTZE);
		msg_pspew("[%02x]", readarr[count]);
	}
	msg_pspew("\n");

	return 0;
}

struct spispeed {
	const char *const name;
	const uint8_t speed;
};

static const struct spispeed spispeeds[] = {
	{ "66 MHz",	0x00 },
	{ "33 MHz",	0x01 },
	{ "22 MHz",	0x02 },
	{ "16.5 MHz",	0x03 },
	{ "100 MHz",	0x04 },
	{ "Reserved",	0x05 },
	{ "Reserved",	0x06 },
	{ "800 kHz",	0x07 },
};

static int set_speed(struct pci_dev *dev, const struct spispeed *spispeed)
{
	bool success = false;
	uint8_t speed = spispeed->speed;

	msg_pdbg("Setting SPI clock to %s (0x%x).\n", spispeed->name, speed);
	if (amd_gen >= CHIPSET_YANGTZE) {
		rmmio_writew((speed << 12) | (speed << 8) | (speed << 4) | speed, sb600_spibar + 0x22);
		uint16_t tmp = mmio_readw(sb600_spibar + 0x22);
		success = (((tmp >> 12) & 0xf) == speed && ((tmp >> 8) & 0xf) == speed &&
			   ((tmp >> 4) & 0xf) == speed && ((tmp >> 0) & 0xf) == speed);
	} else {
		rmmio_writeb((mmio_readb(sb600_spibar + 0xd) & ~(0x3 << 4)) | (speed << 4), sb600_spibar + 0xd);
		success = (speed == ((mmio_readb(sb600_spibar + 0xd) >> 4) & 0x3));
	}

	if (!success) {
		msg_perr("Setting SPI clock failed.\n");
		return 1;
	}
	return 0;
}

static int set_mode(struct pci_dev *dev, uint8_t read_mode)
{
	uint32_t tmp = mmio_readl(sb600_spibar + 0x00);
	tmp &= ~(0x6 << 28 | 0x1 << 18); /* Clear mode bits */
	tmp |= ((read_mode & 0x6) << 28) | ((read_mode & 0x1) << 18);
	rmmio_writel(tmp, sb600_spibar + 0x00);
	if (tmp != mmio_readl(sb600_spibar + 0x00))
		return 1;
	return 0;
}

static int handle_speed(struct pci_dev *dev)
{
	uint32_t tmp;
	uint8_t spispeed_idx = 3; /* Default to 16.5 MHz */

	char *spispeed = extract_programmer_param("spispeed");
	if (spispeed != NULL) {
		unsigned int i;
		for (i = 0; i < ARRAY_SIZE(spispeeds); i++) {
			if (strcasecmp(spispeeds[i].name, spispeed) == 0) {
				spispeed_idx = i;
				break;
			}
		}
		/* "reserved" is not a valid speed.
		 * Error out on speeds not present in the spispeeds array.
		 * Only Yangtze supports the second half of indices.
		 * No 66 MHz before SB8xx. */
		if ((strcasecmp(spispeed, "reserved") == 0) ||
		    (i == ARRAY_SIZE(spispeeds)) ||
		    (amd_gen < CHIPSET_YANGTZE && spispeed_idx > 3) ||
		    (amd_gen < CHIPSET_SB89XX && spispeed_idx == 0)) {
			msg_perr("Error: Invalid spispeed value: '%s'.\n", spispeed);
			free(spispeed);
			return 1;
		}
		free(spispeed);
	}

	/* See the chipset support matrix for SPI Base_Addr below for an explanation of the symbols used.
	 * bit   6xx   7xx/SP5100  8xx             9xx  hudson1  hudson234  bolton/yangtze
	 * 18    rsvd  <-          fastReadEnable  ?    <-       ?          SpiReadMode[0]
	 * 29:30 rsvd  <-          <-              ?    <-       ?          SpiReadMode[2:1]
	 */
	if (amd_gen >= CHIPSET_BOLTON) {
		static const char *spireadmodes[] = {
			"Normal (up to 33 MHz)", /* 0 */
			"Reserved",		 /* 1 */
			"Dual IO (1-1-2)",	 /* 2 */
			"Quad IO (1-1-4)",	 /* 3 */
			"Dual IO (1-2-2)",	 /* 4 */
			"Quad IO (1-4-4)",	 /* 5 */
			"Normal (up to 66 MHz)", /* 6 */
			"Fast Read",		 /* 7 (Not defined in the Bolton datasheet.) */
		};
		tmp = mmio_readl(sb600_spibar + 0x00);
		uint8_t read_mode = ((tmp >> 28) & 0x6) | ((tmp >> 18) & 0x1);
		msg_pdbg("SpiReadMode=%s (%i)\n", spireadmodes[read_mode], read_mode);
		if (read_mode != 6) {
			read_mode = 6; /* Default to "Normal (up to 66 MHz)" */
			if (set_mode(dev, read_mode) != 0) {
				msg_perr("Setting read mode to \"%s\" failed.\n", spireadmodes[read_mode]);
				return 1;
			}
			msg_pdbg("Setting read mode to \"%s\" succeeded.\n", spireadmodes[read_mode]);
		}

		if (amd_gen >= CHIPSET_YANGTZE) {
			tmp = mmio_readb(sb600_spibar + 0x20);
			msg_pdbg("UseSpi100 is %sabled\n", (tmp & 0x1) ? "en" : "dis");
			if ((tmp & 0x1) == 0) {
				rmmio_writeb(tmp | 0x1, sb600_spibar + 0x20);
				tmp = mmio_readb(sb600_spibar + 0x20) & 0x1;
				if (tmp == 0) {
					msg_perr("Enabling Spi100 failed.\n");
					return 1;
				}
				msg_pdbg("Enabling Spi100 succeeded.\n");
			}

			tmp = mmio_readw(sb600_spibar + 0x22); /* SPI 100 Speed Config */
			msg_pdbg("NormSpeedNew is %s\n", spispeeds[(tmp >> 12) & 0xf].name);
			msg_pdbg("FastSpeedNew is %s\n", spispeeds[(tmp >> 8) & 0xf].name);
			msg_pdbg("AltSpeedNew is %s\n", spispeeds[(tmp >> 4) & 0xf].name);
			msg_pdbg("TpmSpeedNew is %s\n", spispeeds[(tmp >> 0) & 0xf].name);
		}
	} else {
		if (amd_gen >= CHIPSET_SB89XX && amd_gen <= CHIPSET_HUDSON234) {
			bool fast_read = (mmio_readl(sb600_spibar + 0x00) >> 18) & 0x1;
			msg_pdbg("Fast Reads are %sabled\n", fast_read ? "en" : "dis");
			if (fast_read) {
				msg_pdbg("Disabling them temporarily.\n");
				rmmio_writel(mmio_readl(sb600_spibar + 0x00) & ~(0x1 << 18),
					     sb600_spibar + 0x00);
			}
		}
		tmp = (mmio_readb(sb600_spibar + 0xd) >> 4) & 0x3;
		msg_pdbg("NormSpeed is %s\n", spispeeds[tmp].name);
	}
	return set_speed(dev, &spispeeds[spispeed_idx]);
}

static int handle_imc(struct pci_dev *dev)
{
	/* Handle IMC everywhere but sb600 which does not have one. */
	if (amd_gen == CHIPSET_SB6XX)
		return 0;

	bool amd_imc_force = false;
	char *arg = extract_programmer_param("amd_imc_force");
	if (arg && !strcmp(arg, "yes")) {
		amd_imc_force = true;
		msg_pspew("amd_imc_force enabled.\n");
	} else if (arg && !strlen(arg)) {
		msg_perr("Missing argument for amd_imc_force.\n");
		free(arg);
		return 1;
	} else if (arg) {
		msg_perr("Unknown argument for amd_imc_force: \"%s\" (not \"yes\").\n", arg);
		free(arg);
		return 1;
	}
	free(arg);

	/* TODO: we should not only look at IntegratedImcPresent (LPC Dev 20, Func 3, 40h) but also at
	 * IMCEnable(Strap) and Override EcEnable(Strap) (sb8xx, sb9xx?, a50, Bolton: Misc_Reg: 80h-87h;
	 * sb7xx, sp5100: PM_Reg: B0h-B1h) etc. */
	uint8_t reg = pci_read_byte(dev, 0x40);
	if ((reg & (1 << 7)) == 0) {
		msg_pdbg("IMC is not active.\n");
		return 0;
	}

	/* On Yangtze and newer chips, check the EcEnableStrap bit */
	if ((amd_gen >= CHIPSET_YANGTZE) && (pm_ioread(ISA_CONTROL) & MMIO_EN )) {
		uint8_t *AcpiMMIO = rphysmap("AMD ACPI registers", ACPI_MMIO_BASE & 0xfffff000, 0x1000);
		if (AcpiMMIO != ERROR_PTR) {
			AcpiMMIO += MISC_BASE + STRAP_STATUS;
			uint32_t straps = mmio_readl(AcpiMMIO);
			if ((straps & EC_ENABLE_STRAP) == 0){
				msg_pinfo("IMC is not active.\n");
				return 0;
			} else {
				msg_pinfo("IMC IS active! Straps: %08x (%p)\n", straps, (void *)AcpiMMIO);
				msg_pinfo("StrapOverride: %08x\n", mmio_readl(AcpiMMIO + 4));
			}

		} else {
			msg_pinfo("Error reading AMD ACPI registers.\n");
		}
	}

	if (!amd_imc_force)
		programmer_may_write = 0;
	msg_pinfo("Writes have been disabled for safety reasons because the presence of the IMC\n"
		  "was detected and it could interfere with accessing flash memory. Flashrom will\n"
		  "try to disable it temporarily but even then this might not be safe:\n"
		  "when it is re-enabled and after a reboot it expects to find working code\n"
		  "in the flash and it is unpredictable what happens if there is none.\n"
		  "\n"
		  "To be safe make sure that there is a working IMC firmware at the right\n"
		  "location in the image you intend to write and do not attempt to erase.\n"
		  "\n"
		  "You can enforce write support with the amd_imc_force programmer option.\n");
	if (amd_imc_force)
		msg_pinfo("Continuing with write support because the user forced us to!\n");

	return amd_imc_shutdown(dev);
}

int sb600_probe_spi(struct pci_dev *dev)
{
	struct pci_dev *smbus_dev;
	uint32_t tmp;
	uint8_t reg;

	/* Read SPI_BaseAddr */
	tmp = pci_read_long(dev, 0xa0);
	tmp &= 0xffffffe0;	/* remove bits 4-0 (reserved) */
	msg_pdbg("SPI base address is at 0x%x\n", tmp);

	/* If the BAR has address 0, it is unlikely SPI is used. */
	if (!tmp)
		return 0;

	/* Physical memory has to be mapped at page (4k) boundaries. */
	sb600_spibar = rphysmap("SB600 SPI registers", tmp & 0xfffff000, 0x1000);
	if (sb600_spibar == ERROR_PTR)
		return ERROR_FATAL;

	/* The low bits of the SPI base address are used as offset into
	 * the mapped page.
	 */
	sb600_spibar += tmp & 0xfff;

	if (determine_generation(dev, &smbus_dev) != 0) {
		return ERROR_NONFATAL;
	}

	/* How to read the following table and similar ones in this file:
	 * "?" means we have no datasheet for this chipset generation or it doesn't have any relevant info.
	 * "<-" means the bit/register meaning is identical to the next non-"?" chipset to the left. "<-" thus
	 *      never refers to another "?".
	 * If a "?" chipset is between two chipsets with identical meaning, we assume the meaning didn't change
	 * twice in between, i.e. the meaning is unchanged for the "?" chipset. Usually we assume that
	 * succeeding hardware supports the same functionality as its predecessor unless proven different by
	 * tests or documentation, hence "?" will often be implemented equally to "<-".
	 *
	 * Chipset support matrix for SPI Base_Addr (LPC PCI reg 0xa0)
	 * bit   6xx         7xx/SP5100       8xx       9xx  hudson1  hudson2+  yangtze
	 * 3    rsvd         <-               <-        ?    <-       ?         RouteTpm2Spi
	 * 2    rsvd         AbortEnable      rsvd      ?    <-       ?         <-
	 * 1    rsvd         SpiRomEnable     <-        ?    <-       ?         <-
	 * 0    rsvd         AltSpiCSEnable   rsvd      ?    <-       ?         <-
	 */
	if (amd_gen >= CHIPSET_SB7XX) {
		tmp = pci_read_long(dev, 0xa0);
		msg_pdbg("SpiRomEnable=%i", (tmp >> 1) & 0x1);
		if (amd_gen == CHIPSET_SB7XX)
			msg_pdbg(", AltSpiCSEnable=%i, AbortEnable=%i", tmp & 0x1, (tmp >> 2) & 0x1);
		else if (amd_gen >= CHIPSET_YANGTZE)
			msg_pdbg(", RouteTpm2Sp=%i", (tmp >> 3) & 0x1);

		tmp = pci_read_byte(dev, 0xba);
		msg_pdbg(", PrefetchEnSPIFromIMC=%i", (tmp & 0x4) >> 2);

		tmp = pci_read_byte(dev, 0xbb);
		/* FIXME: Set bit 3,6,7 if not already set.
		 * Set bit 5, otherwise SPI accesses are pointless in LPC mode.
		 * See doc 42413 AMD SB700/710/750 RPR.
		 */
		if (amd_gen == CHIPSET_SB7XX)
			msg_pdbg(", SpiOpEnInLpcMode=%i", (tmp >> 5) & 0x1);
		msg_pdbg(", PrefetchEnSPIFromHost=%i\n", tmp & 0x1);
	}

	/* Chipset support matrix for SPI_Cntrl0 (spibar + 0x0)
	 * See the chipset support matrix for SPI Base_Addr above for an explanation of the symbols used.
	 * bit   6xx                7xx/SP5100      8xx               9xx  hudson1  hudson2+  yangtze
	 * 17    rsvd               <-              <-                ?    <-       ?         <-
	 * 18    rsvd               <-              fastReadEnable<1> ?    <-       ?         SpiReadMode[0]<1>
	 * 19    SpiArbEnable       <-              <-                ?    <-       ?         <-
	 * 20    (FifoPtrClr)       <-              <-                ?    <-       ?         <-
	 * 21    (FifoPtrInc)       <-              <-                ?    <-       ?         IllegalAccess
	 * 22    SpiAccessMacRomEn  <-              <-                ?    <-       ?         <-
	 * 23    SpiHostAccessRomEn <-              <-                ?    <-       ?         <-
	 * 24:26 ArbWaitCount       <-              <-                ?    <-       ?         <-
	 * 27    SpiBridgeDisable   <-              <-                ?    <-       ?         rsvd
	 * 28    rsvd               DropOneClkOnRd  = SPIClkGate      ?    <-       ?         <-
	 * 29:30 rsvd               <-              <-                ?    <-       ?         SpiReadMode[2:1]<1>
	 * 31    rsvd               <-              SpiBusy           ?    <-       ?         <-
	 *
	 *  <1> see handle_speed
	 */
	tmp = mmio_readl(sb600_spibar + 0x00);
	msg_pdbg("(0x%08x) SpiArbEnable=%i", tmp, (tmp >> 19) & 0x1);
	if (amd_gen >= CHIPSET_YANGTZE)
		msg_pdbg(", IllegalAccess=%i", (tmp >> 21) & 0x1);

	msg_pdbg(", SpiAccessMacRomEn=%i, SpiHostAccessRomEn=%i, ArbWaitCount=%i",
		 (tmp >> 22) & 0x1, (tmp >> 23) & 0x1, (tmp >> 24) & 0x7);

	if (amd_gen < CHIPSET_YANGTZE)
		msg_pdbg(", SpiBridgeDisable=%i", (tmp >> 27) & 0x1);

	switch (amd_gen) {
	case CHIPSET_SB7XX:
		msg_pdbg(", DropOneClkOnRd/SpiClkGate=%i", (tmp >> 28) & 0x1);
	case CHIPSET_SB89XX:
	case CHIPSET_HUDSON234:
	case CHIPSET_YANGTZE:
	case CHIPSET_PROMONTORY:
		msg_pdbg(", SpiBusy=%i", (tmp >> 31) & 0x1);
	default: break;
	}
	msg_pdbg("\n");

	if (((tmp >> 22) & 0x1) == 0 || ((tmp >> 23) & 0x1) == 0) {
		msg_perr("ERROR: State of SpiAccessMacRomEn or SpiHostAccessRomEn prohibits full access.\n");
		return ERROR_NONFATAL;
	}

	if (amd_gen >= CHIPSET_SB89XX) {
		tmp = mmio_readb(sb600_spibar + 0x1D);
		msg_pdbg("Using SPI_CS%d\n", tmp & 0x3);
		/* FIXME: Handle SpiProtect* configuration on Yangtze. */
	}

	/* Note about the bit tests below: If a bit is zero, the GPIO is SPI. */
	/* GPIO11/SPI_DO and GPIO12/SPI_DI status */
	reg = pci_read_byte(smbus_dev, 0xAB);
	reg &= 0xC0;
	msg_pdbg("GPIO11 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_DO");
	msg_pdbg("GPIO12 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_DI");
	if (reg != 0x00) {
		msg_pdbg("Not enabling SPI");
		return 0;
	}
	/* GPIO31/SPI_HOLD and GPIO32/SPI_CS status */
	reg = pci_read_byte(smbus_dev, 0x83);
	reg &= 0xC0;
	msg_pdbg("GPIO31 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_HOLD");
	msg_pdbg("GPIO32 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_CS");
	/* SPI_HOLD is not used on all boards, filter it out. */
	if ((reg & 0x80) != 0x00) {
		msg_pdbg("Not enabling SPI");
		return 0;
	}
	/* GPIO47/SPI_CLK status */
	reg = pci_read_byte(smbus_dev, 0xA7);
	reg &= 0x40;
	msg_pdbg("GPIO47 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_CLK");
	if (reg != 0x00) {
		msg_pdbg("Not enabling SPI");
		return 0;
	}

	if (handle_speed(dev) != 0)
		return ERROR_FATAL;

	if (handle_imc(dev) != 0)
		return ERROR_FATAL;

	/* Starting with Yangtze the SPI controller got a different interface with a much bigger buffer. */
	if (amd_gen < CHIPSET_YANGTZE)
		register_spi_master(&spi_master_sb600);
	else
		register_spi_master(&spi_master_yangtze);
	return 0;
}

#endif