| /* |
| * This file is part of the flashrom project. |
| * |
| * Copyright (C) 2014 Google Inc. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * |
| * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * |
| * Neither the name of Google or the names of contributors or |
| * licensors may be used to endorse or promote products derived from this |
| * software without specific prior written permission. |
| * |
| * This software is provided "AS IS," without a warranty of any kind. |
| * ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, |
| * INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A |
| * PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE HEREBY EXCLUDED. |
| * GOOGLE INC AND ITS LICENSORS SHALL NOT BE LIABLE |
| * FOR ANY DAMAGES SUFFERED BY LICENSEE AS A RESULT OF USING, MODIFYING |
| * OR DISTRIBUTING THIS SOFTWARE OR ITS DERIVATIVES. IN NO EVENT WILL |
| * GOOGLE OR ITS LICENSORS BE LIABLE FOR ANY LOST REVENUE, PROFIT OR DATA, |
| * OR FOR DIRECT, INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL OR |
| * PUNITIVE DAMAGES, HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF |
| * LIABILITY, ARISING OUT OF THE USE OF OR INABILITY TO USE THIS SOFTWARE, |
| * EVEN IF GOOGLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. |
| * |
| * s25f.c - Helper functions for Spansion S25FL and S25FS SPI flash chips. |
| * Uses 24 bit addressing for the FS chips and 32 bit addressing for the FL |
| * chips (which is required by the overlayed sector size devices). |
| * TODO: Implement fancy hybrid sector architecture helpers. |
| */ |
| |
| #include <string.h> |
| |
| #include "chipdrivers.h" |
| #include "spi.h" |
| #include "writeprotect.h" |
| |
| /* |
| * RDAR and WRAR are supported on chips which have more than one set of status |
| * and control registers and take an address of the register to read/write. |
| * WRR, RDSR2, and RDCR are used on chips with a more limited set of control/ |
| * status registers. |
| * |
| * WRR is somewhat peculiar. It shares the same opcode as JEDEC_WRSR, and if |
| * given one data byte (following the opcode) it acts the same way. If it's |
| * given two data bytes, the first data byte overwrites status register 1 |
| * and the second data byte overwrites config register 1. |
| */ |
| #define CMD_WRR 0x01 |
| #define CMD_WRDI 0x04 |
| #define CMD_RDSR2 0x07 /* note: read SR1 with JEDEC RDSR opcode */ |
| #define CMD_RDCR 0x35 |
| #define CMD_RDAR 0x65 |
| #define CMD_WRAR 0x71 |
| |
| /* TODO: For now, commands which use an address assume 24-bit addressing */ |
| #define CMD_WRR_LEN 3 |
| #define CMD_WRDI_LEN 1 |
| #define CMD_RDAR_LEN 4 |
| #define CMD_WRAR_LEN 5 |
| |
| #define CMD_RSTEN 0x66 |
| #define CMD_RST 0x99 |
| |
| #define CR1NV_ADDR 0x000002 |
| #define CR1_BPNV_O (1 << 3) |
| #define CR1_TBPROT_O (1 << 5) |
| #define CR3NV_ADDR 0x000004 |
| #define CR3NV_20H_NV (1 << 3) |
| |
| /* See "Embedded Algorithm Performance Tables for additional timing specs. */ |
| #define T_W 145 * 1000 /* NV register write time (145ms) */ |
| #define T_RPH 35 /* Reset pulse hold time (35us) */ |
| #define S25FS_T_SE 145 * 1000 /* Sector Erase Time (145ms) */ |
| #define S25FL_T_SE 130 * 1000 /* Sector Erase Time (130ms) */ |
| |
| static int s25f_legacy_software_reset(const struct flashctx *flash) |
| { |
| int result; |
| struct spi_command cmds[] = { |
| { |
| .writecnt = 1, |
| .writearr = (const unsigned char[]){ CMD_RSTEN }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 1, |
| .writearr = (const unsigned char[]){ 0xf0 }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .writearr = NULL, |
| .readcnt = 0, |
| .readarr = NULL, |
| }}; |
| |
| result = spi_send_multicommand(flash, cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution\n", __func__); |
| return result; |
| } |
| |
| /* Allow time for reset command to execute. The datasheet specifies |
| * Trph = 35us, double that to be safe. */ |
| programmer_delay(T_RPH * 2); |
| |
| return 0; |
| } |
| |
| /* "Legacy software reset" is disabled by default on S25FS, use this instead. */ |
| static int s25fs_software_reset(struct flashctx *flash) |
| { |
| int result; |
| struct spi_command cmds[] = { |
| { |
| .writecnt = 1, |
| .writearr = (const unsigned char[]){ CMD_RSTEN }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 1, |
| .writearr = (const unsigned char[]){ CMD_RST }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .writearr = NULL, |
| .readcnt = 0, |
| .readarr = NULL, |
| }}; |
| |
| result = spi_send_multicommand(flash, cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution\n", __func__); |
| return result; |
| } |
| |
| /* Allow time for reset command to execute. Double tRPH to be safe. */ |
| programmer_delay(T_RPH * 2); |
| |
| return 0; |
| } |
| |
| static int s25f_poll_status(const struct flashctx *flash) |
| { |
| uint8_t tmp = spi_read_status_register(flash); |
| |
| while (tmp & SPI_SR_WIP) { |
| /* |
| * The WIP bit on S25F chips remains set to 1 if erase or |
| * programming errors occur, so we must check for those |
| * errors here. If an error is encountered, do a software |
| * reset to clear WIP and other volatile bits, otherwise |
| * the chip will be unresponsive to further commands. |
| */ |
| if (tmp & SPI_SR_ERA_ERR) { |
| msg_cerr("Erase error occurred\n"); |
| s25f_legacy_software_reset(flash); |
| return -1; |
| } |
| |
| if (tmp & (1 << 6)) { |
| msg_cerr("Programming error occurred\n"); |
| s25f_legacy_software_reset(flash); |
| return -1; |
| } |
| |
| programmer_delay(1000 * 10); |
| tmp = spi_read_status_register(flash); |
| } |
| |
| return 0; |
| } |
| |
| /* "Read Any Register" instruction only supported on S25FS */ |
| static int s25fs_read_cr(const struct flashctx *flash, uint32_t addr) |
| { |
| int result; |
| uint8_t cfg; |
| /* By default, 8 dummy cycles are necessary for variable-latency |
| commands such as RDAR (see CR2NV[3:0]). */ |
| unsigned char read_cr_cmd[] = { |
| CMD_RDAR, |
| (addr >> 16) & 0xff, |
| (addr >> 8) & 0xff, |
| (addr & 0xff), |
| 0x00, 0x00, 0x00, 0x00, |
| 0x00, 0x00, 0x00, 0x00, |
| }; |
| |
| result = spi_send_command(flash, sizeof(read_cr_cmd), 1, read_cr_cmd, &cfg); |
| if (result) { |
| msg_cerr("%s failed during command execution at address 0x%x\n", |
| __func__, addr); |
| return -1; |
| } |
| |
| return cfg; |
| } |
| |
| static int s25f_read_cr1(const struct flashctx *flash) |
| { |
| int result; |
| uint8_t cfg; |
| unsigned char read_cr_cmd[] = { CMD_RDCR }; |
| |
| result = spi_send_command(flash, sizeof(read_cr_cmd), 1, read_cr_cmd, &cfg); |
| if (result) { |
| msg_cerr("%s failed during command execution\n", __func__); |
| return -1; |
| } |
| |
| return cfg; |
| } |
| |
| /* "Write Any Register" instruction only supported on S25FS */ |
| static int s25fs_write_cr(const struct flashctx *flash, |
| uint32_t addr, uint8_t data) |
| { |
| int result; |
| struct spi_command cmds[] = { |
| { |
| .writecnt = JEDEC_WREN_OUTSIZE, |
| .writearr = (const unsigned char[]){ JEDEC_WREN }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = CMD_WRAR_LEN, |
| .writearr = (const unsigned char[]){ |
| CMD_WRAR, |
| (addr >> 16) & 0xff, |
| (addr >> 8) & 0xff, |
| (addr & 0xff), |
| data |
| }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .writearr = NULL, |
| .readcnt = 0, |
| .readarr = NULL, |
| }}; |
| |
| result = spi_send_multicommand(flash, cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution at address 0x%x\n", |
| __func__, addr); |
| return -1; |
| } |
| |
| programmer_delay(T_W); |
| return s25f_poll_status(flash); |
| } |
| |
| static int s25f_write_cr1(const struct flashctx *flash, uint8_t data) |
| { |
| int result; |
| struct spi_command cmds[] = { |
| { |
| .writecnt = JEDEC_WREN_OUTSIZE, |
| .writearr = (const unsigned char[]){ JEDEC_WREN }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = CMD_WRR_LEN, |
| .writearr = (const unsigned char[]){ |
| CMD_WRR, |
| spi_read_status_register(flash), |
| data, |
| }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .writearr = NULL, |
| .readcnt = 0, |
| .readarr = NULL, |
| }}; |
| |
| result = spi_send_multicommand(flash, cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution\n", __func__); |
| return -1; |
| } |
| |
| programmer_delay(T_W); |
| return s25f_poll_status(flash); |
| } |
| |
| static int s25fs_restore_cr3nv(struct flashctx *flash, uint8_t cfg) |
| { |
| int ret = 0; |
| |
| msg_cdbg("Restoring CR3NV value to 0x%02x\n", cfg); |
| ret |= s25fs_write_cr(flash, CR3NV_ADDR, cfg); |
| ret |= s25fs_software_reset(flash); |
| return ret; |
| } |
| |
| /* returns state of top/bottom block protection, or <0 to indicate error */ |
| static int s25f_get_tbprot_o(const struct flashctx *flash) |
| { |
| int cr1 = s25f_read_cr1(flash); |
| |
| if (cr1 < 0) |
| return -1; |
| |
| /* |
| * 1 = BP starts at bottom (low address) |
| * 0 = BP start at top (high address) |
| */ |
| return cr1 & CR1_TBPROT_O ? 1 : 0; |
| } |
| |
| /* fills modifier_bits struct, returns 0 to indicate success */ |
| int s25f_get_modifier_bits(const struct flashctx *flash, |
| struct generic_modifier_bits *m) |
| { |
| int tmp; |
| |
| memset(m, 0, sizeof(*m)); |
| |
| tmp = s25f_get_tbprot_o(flash); |
| if (tmp < 0) |
| return -1; |
| m->tb = tmp; |
| |
| return 0; |
| } |
| |
| int s25f_set_modifier_bits(const struct flashctx *flash, |
| struct generic_modifier_bits *m) |
| { |
| int cr1, cr1_orig; |
| |
| cr1 = cr1_orig = s25f_read_cr1(flash); |
| if (cr1 < 0) |
| return -1; |
| |
| /* |
| * Clear BPNV so that setting BP2-0 in status register gets |
| * written to non-volatile memory. |
| * |
| * For TBPROT: |
| * 1 = BP starts at bottom (low address) |
| * 0 = BP start at top (high address) |
| */ |
| cr1 &= ~(CR1_BPNV_O | CR1_TBPROT_O); |
| cr1 |= m->tb ? CR1_TBPROT_O : 0; |
| |
| if (cr1 != cr1_orig) { |
| msg_cdbg("%s: setting cr1 bits to 0x%02x\n", __func__, cr1); |
| if (s25f_write_cr1(flash, cr1) < 0) |
| return -1; |
| if (s25f_read_cr1(flash) != cr1) { |
| msg_cerr("%s: failed to set CR1 value\n", __func__); |
| return -1; |
| } |
| } else { |
| msg_cdbg("%s: cr1 bits already match desired value: " |
| "0x%02x\n", __func__, cr1); |
| } |
| |
| return 0; |
| } |
| |
| int s25fs_block_erase_d8(struct flashctx *flash, |
| unsigned int addr, unsigned int blocklen) |
| { |
| unsigned char cfg; |
| int result; |
| static int cr3nv_checked = 0; |
| |
| struct spi_command erase_cmds[] = { |
| { |
| .writecnt = JEDEC_WREN_OUTSIZE, |
| .writearr = (const unsigned char[]){ JEDEC_WREN }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = JEDEC_BE_D8_OUTSIZE, |
| .writearr = (const unsigned char[]){ |
| JEDEC_BE_D8, |
| (addr >> 16) & 0xff, |
| (addr >> 8) & 0xff, |
| (addr & 0xff) |
| }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .writearr = NULL, |
| .readcnt = 0, |
| .readarr = NULL, |
| }}; |
| |
| /* Check if hybrid sector architecture is in use and, if so, |
| * switch to uniform sectors. */ |
| if (!cr3nv_checked) { |
| cfg = s25fs_read_cr(flash, CR3NV_ADDR); |
| if (!(cfg & CR3NV_20H_NV)) { |
| s25fs_write_cr(flash, CR3NV_ADDR, cfg | CR3NV_20H_NV); |
| s25fs_software_reset(flash); |
| |
| cfg = s25fs_read_cr(flash, CR3NV_ADDR); |
| if (!(cfg & CR3NV_20H_NV)) { |
| msg_cerr("%s: Unable to enable uniform " |
| "block sizes.\n", __func__); |
| return 1; |
| } |
| |
| msg_cdbg("\n%s: CR3NV updated (0x%02x -> 0x%02x)\n", |
| __func__, cfg, |
| s25fs_read_cr(flash, CR3NV_ADDR)); |
| /* Restore CR3V when flashrom exits */ |
| register_chip_restore(s25fs_restore_cr3nv, flash, cfg); |
| } |
| |
| cr3nv_checked = 1; |
| } |
| |
| result = spi_send_multicommand(flash, erase_cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution at address 0x%x\n", |
| __func__, addr); |
| return result; |
| } |
| |
| programmer_delay(S25FS_T_SE); |
| return s25f_poll_status(flash); |
| } |
| |
| int s25fl_block_erase(struct flashctx *flash, |
| unsigned int addr, unsigned int blocklen) |
| { |
| int result; |
| |
| struct spi_command erase_cmds[] = { |
| { |
| .writecnt = JEDEC_WREN_OUTSIZE, |
| .writearr = (const unsigned char[]){ |
| JEDEC_WREN |
| }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = JEDEC_BE_DC_OUTSIZE, |
| .writearr = (const unsigned char[]){ |
| JEDEC_BE_DC, |
| (addr >> 24) & 0xff, |
| (addr >> 16) & 0xff, |
| (addr >> 8) & 0xff, |
| (addr & 0xff) |
| }, |
| .readcnt = 0, |
| .readarr = NULL, |
| }, { |
| .writecnt = 0, |
| .readcnt = 0, |
| } |
| }; |
| |
| result = spi_send_multicommand(flash, erase_cmds); |
| if (result) { |
| msg_cerr("%s failed during command execution at address 0x%x\n", |
| __func__, addr); |
| return result; |
| } |
| |
| programmer_delay(S25FL_T_SE); |
| return s25f_poll_status(flash); |
| } |
| |
| |
| int probe_spi_big_spansion(struct flashctx *flash) |
| { |
| static const unsigned char cmd = JEDEC_RDID; |
| int ret; |
| unsigned char dev_id[6]; /* We care only about 6 first bytes */ |
| |
| ret = spi_send_command(flash, sizeof(cmd), sizeof(dev_id), &cmd, dev_id); |
| |
| if (!ret) { |
| int i; |
| |
| for (i = 0; i < sizeof(dev_id); i++) |
| msg_gdbg(" 0x%02x", dev_id[i]); |
| msg_gdbg(".\n"); |
| |
| if (dev_id[0] == flash->chip->manufacture_id) { |
| union { |
| uint8_t array[4]; |
| uint32_t whole; |
| } model_id; |
| |
| /* |
| * The structure of the RDID output is as follows: |
| * |
| * offset value meaning |
| * 00h 01h Manufacturer ID for Spansion |
| * 01h 20h 128 Mb capacity |
| * 01h 02h 256 Mb capacity |
| * 02h 18h 128 Mb capacity |
| * 02h 19h 256 Mb capacity |
| * 03h 4Dh Full size of the RDID output (ignored) |
| * 04h 00h FS: 256-kB physical sectors |
| * 04h 01h FS: 64-kB physical sectors |
| * 04h 00h FL: 256-kB physical sectors |
| * 04h 01h FL: Mix of 64-kB and 4KB overlayed sectors |
| * 05h 80h FL family |
| * 05h 81h FS family |
| * |
| * Need to use bytes 1, 2, 4, and 5 to properly identify one of eight |
| * possible chips: |
| * |
| * 2 types * 2 possible sizes * 2 possible sector layouts |
| * |
| */ |
| memcpy(model_id.array, dev_id + 1, 2); |
| memcpy(model_id.array + 2, dev_id + 4, 2); |
| if (be_to_cpu32(model_id.whole) == flash->chip->model_id) |
| return 1; |
| } |
| } |
| return 0; |
| } |