servo/data/servo_v2_r0.xml

<?xml version="1.0"?>
<root>
  <!-- ********** Maps ********** -->
  <include>
    <name>common.xml</name>
  </include>
  <include>
    <name>keyboard.xml</name>
  </include>
  <include>
    <name>uart_common.xml</name>
  </include>
  <include>
    <name>ftdii2c_cmd.xml</name>
  </include>
  <include>
    <name>usb_image_management.xml</name>
  </include>
  <map>
    <name>i2c_mux</name>
    <doc>4 to 1 mux to steer ftdi i2c bus to different sets of
    adcs.</doc>
    <params local_adc_ch0="0" local_adc_ch1="1" remote_adc="2"
    reserved="3" loc0="0" loc1="1" rem="2" atmega="3"></params>
  </map>
  <map>
    <name>usbkey</name>
    <doc>Determines whether DUT or servo sees USB port (TYPE A/J3
    and TYPE A/J8)</doc>
    <params dut_sees_usbkey="0" servo_sees_usbkey="1"></params>
  </map>
  <map>
    <name>duthub</name>
    <doc>Determine whether DUT sees USB hub or Servo via USB port
    (TYPE MICRO-B/J6)</doc>
    <params dut_sees_hub="0" dut_sees_servo="1"></params>
  </map>
  <map>
    <name>vref_sel</name>
    <doc>Determine VREF between pp3300, pp2500, pp1800 and off.
    Default is off</doc>
    <params pp3300="0" pp2500="1" pp1800="2" off="3"></params>
  </map>
  <map>
    <name>onoff_vref_sel</name>
    <doc>Determine VREF between on, pp3300, pp2500, pp1800 and off.
    Default is off</doc>
    <params on="0" pp3300="0" pp2500="1" pp1800="2" off="3"></params>
  </map>
  <!-- *********** FT4232H U29 Interface 1 ********** -->
  <!-- JTAG -->
  <!-- *********** FT4232H U29 Interface 2 ********** -->
  <!-- I2C -->
  <!-- *********** FT4232H U29 Interface 3 ********** -->
  <!-- UART -->
  <control>
    <name>uart3_pty</name>
    <alias>legacy_uart_pty</alias>
    <doc>Legacy (v1) uart console. Typically connected to CPU's
    uart console for devices which supported it.</doc>
    <params cmd="get" subtype="pty" interface="3" drv="uart">
    </params>
  </control>
  <control>
    <name>uart3_baudrate</name>
    <alias>legacy_uart_baudrate</alias>
    <doc>Baudrate for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="baudrate"
    interface="3"></params>
  </control>
  <control>
    <name>uart3_parity</name>
    <alias>legacy_uart_parity</alias>
    <doc>Parity for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="parity"
    interface="3" map="uart_parity"></params>
  </control>
  <control>
    <name>uart3_sbits</name>
    <alias>legacy_uart_sbits</alias>
    <doc>Number of stop bits for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="sbits"
    interface="3" map="uart_sbits"></params>
  </control>
  <control>
    <name>uart3_bits</name>
    <alias>legacy_uart_bits</alias>
    <doc>Number of data bits for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="bits"
    interface="3" map="uart_bits"></params>
  </control>
  <!-- *********** FT4232H U29 Interface 4 ********** -->
  <!-- UART -->
  <control>
    <name>atmega_pty</name>
    <doc>atmega_pty</doc>
    <params cmd="get" subtype="pty" interface="4" drv="uart">
    </params>
  </control>
  <control>
    <name>atmega_baudrate</name>
    <alias>legacy_uart_baudrate</alias>
    <doc>Baudrate for Atmega's uart console</doc>
    <params drv="uart" subtype="props" line_prop="baudrate"
    interface="4"></params>
  </control>
  <control>
    <name>atmega_parity</name>
    <alias>legacy_uart_parity</alias>
    <doc>Parity for Atmega's uart console</doc>
    <params drv="uart" subtype="props" line_prop="parity"
    interface="4" map="uart_parity"></params>
  </control>
  <control>
    <name>atmega_sbits</name>
    <alias>legacy_uart_sbits</alias>
    <doc>Number of stop bits for Atmega's uart console</doc>
    <params drv="uart" subtype="props" line_prop="sbits"
    interface="4" map="uart_sbits"></params>
  </control>
  <control>
    <name>atmega_bits</name>
    <alias>legacy_uart_bits</alias>
    <doc>Number of data bits for Atmega's uart console</doc>
    <params drv="uart" subtype="props" line_prop="bits"
    interface="4" map="uart_bits"></params>
  </control>
  <!-- ********** I2c related controls ********** -->
  <control>
    <name>i2c_mux</name>
    <doc>4to1 mux select which steers i2c bus from FTDI to
    different banks (16) of ina219 adcs</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="0" width="2" map="i2c_mux" init="rem"></params>
  </control>
  <control>
    <name>i2c_mux_en</name>
    <doc>Enable pin (ADG804) of 4to1 mux</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="2" map="onoff" init="on"></params>
  </control>
  <!-- slv 0x20 : ioexpander port 0 -->
  <control>
    <name>dut_flaga</name>
    <doc>dut_flaga</doc>
    <params interface="2" drv="tca6416" slv="0x20" port="0"
    offset="0" map="onoff"></params>
  </control>
  <control>
    <name>dut_flagb</name>
    <doc>dut_flagb</doc>
    <params interface="2" drv="tca6416" slv="0x20" port="0"
    offset="1" map="onoff"></params>
  </control>
  <control>
    <name>pch_disable</name>
    <doc>DUT specific. Note, is aliased to jtag_buf_on_flex_en
    GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="2" map="onoff_i" init="off"></params>
  </control>
  <!-- bit overloaded for enabling flex cable buffers -->
  <control>
    <name>jtag_buf_on_flex_en</name>
    <doc>Enables JTAG buffer on servo flex. Note, is aliased to
    pch_disable GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="2" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>cold_reset</name>
    <doc>cold_reset</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="3" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>warm_reset</name>
    <doc>warm_reset</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="4" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>dev_mode</name>
    <doc>dev_mode GPIO. Note, is aliased to spi1_buf_on_flex_en
    GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="5" map="onoff"></params>
  </control>
  <!-- bit overloaded for enabling flex cable buffers -->
  <control>
    <name>spi1_buf_on_flex_en</name>
    <doc>Enables SPI1 buffers on servo flex. Note, is aliased to
    dev_mode GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="0"
    offset="5" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>tp78</name>
    <doc>tp78 on U25 pin 10</doc>
    <params interface="2" drv="tca6416" slv="0x20" port="0"
    offset="6" map="onoff"></params>
  </control>
  <control>
    <name>sd_detect</name>
    <doc>SD Card detect</doc>
    <params cmd="set" interface="2" drv="tca6416" slv="0x23"
    port="1" offset="7" map="onoff_i"></params>
    <params cmd="get" interface="2" drv="tca6416" slv="0x20"
    port="0" offset="7" map="onoff_i"></params>
  </control>
  <!-- slv 0x20 : ioexpander port 1 -->
  <control>
    <name>spi_hold</name>
    <doc>spi_hold</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="0" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>dut_nmi</name>
    <doc>dut_nmi</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="1" map="onoff"></params>
  </control>
  <control>
    <name>hpd</name>
    <doc>hpd</doc>
    <params interface="2" drv="tca6416" slv="0x20" port="1"
    offset="2" map="onoff"></params>
  </control>
  <control>
    <name>fw_wp</name>
    <doc>Firmware write-protect GPIO</doc>
    <params cmd="get" interface="2" drv="tca6416" slv="0x20"
    port="1" offset="3" map="onoff_i"></params>
    <params cmd="set" interface="2" drv="tca6416" slv="0x22"
    port="1" offset="5" map="onoff_i"></params>
  </control>
  <control>
    <name>pwr_button</name>
    <doc>Power button GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="4" map="press" init="release"></params>
  </control>
  <control>
    <name>lid_open</name>
    <doc>lid open GPIO. Note, is aliased to spi2_buf_on_flex_en
    GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="5" map="yesno" init="yes"></params>
  </control>
  <!-- bit overloaded for enabling flex cable buffers -->
  <control>
    <name>spi2_buf_on_flex_en</name>
    <doc>Enables SPI2 buffers on servo flex. Note, is aliased to
    lid_open GPIO</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="5" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>rec_mode</name>
    <doc>Google recovery mode</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="6" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>fw_up</name>
    <alias>t20_rec,proc_hot,ec_boot_mode</alias>
    <doc>Firmware update mode via USB</doc>
    <params interface="2" drv="tca6416" slv="0x20" od="PU" port="1"
    offset="7" map="onoff_i" init="off"></params>
  </control>
  <!-- slv 0x21 : ioexpander port 0 -->
  <control>
    <name>dut_hub_on</name>
    <doc>Enables DUT's USB hub with ethernet (RJ45/I54) and USB
    port (Vert TYPE A/J3)</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="0" map="yesno_i"></params>
  </control>
  <control>
    <name>usb_mux_oe2</name>
    <doc>Output enable for USB port (TYPE A/J4) to DUT via USB port
    (TYPE MICRO-B/J5)</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="1" map="onoff_i"></params>
  </control>
  <control>
    <name>usb_mux_oe1</name>
    <doc>Output enable for USB port (vert TYPE A/J3) to DUT via DUT
    USB hub</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="2" map="onoff_i"></params>
  </control>
  <control>
    <name>usb_mux_sel1</name>
    <alias>image_usbkey_mux</alias>
    <doc>2to1 mux select for USB port (vert TYPE A/J3). Set either
    'dut_sees_usbkey' or 'servo_sees_usbkey'</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="3" map="usbkey" init="dut_sees_usbkey"></params>
  </control>
  <control>
    <name>dut_hub1_rst1</name>
    <doc>Reset DUT's USB hub with ethernet (RJ45/I54) and USB port
    (TYPE A/J3, TYPE A/J8, TYPE A/J10)</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="4" map="onoff_i"></params>
  </control>
  <control>
    <name>dut_usb2_prtctl</name>
    <doc>power enable for USB port (TYPE A/J4) to DUT via USB port
    (TYPE MICRO-B/J5)</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="5" map="onoff"></params>
  </control>
  <control>
    <name>dut_hub_sel</name>
    <doc>2to1 Mux select for USB port (TYPE MICRO-B/J6). Set either
    'dut_sees_hub' or 'dut_sees_servo'</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="6" map="duthub"></params>
  </control>
  <control>
    <name>prtctl4_pwren</name>
    <alias>image_usbkey_pwr</alias>
    <doc>USB port 4 (TYPE A/J3, USB key) power enable</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="0"
    offset="7" map="onoff" init="on"></params>
  </control>
  <!-- slv 0x21 : ioexpander port 1 -->
  <control>
    <name>blinky</name>
    <doc>LED on gpio for blinking</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="3" map="onoff_i"></params>
  </control>
  <control>
    <name>uart3_en</name>
    <alias>legacy_uart_en</alias>
    <doc>Enable communication with legacy (v1) uart console.</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="4" map="onoff_i" init="on"></params>
  </control>
  <control>
    <name>dut_hub_pwren</name>
    <doc>enable power to DUT's USB hub</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="5" map="onoff" init="on"></params>
  </control>
  <control>
    <name>usb_mux_sel3</name>
    <doc>2to1 mux select for USB port (vert TYPE A/J8). Set either
    'dut_sees_usbkey' or 'servo_sees_usbkey'</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="6" map="usbkey"></params>
  </control>
  <control>
    <name>usb_mux_oe3</name>
    <doc>Output enable for USB port (vert TYPE A/J8) to DUT via DUT
    USB hub</doc>
    <params interface="2" drv="tca6416" slv="0x21" port="1"
    offset="7" map="onoff_i"></params>
  </control>
  <!-- slv 0x22 : ioexpander port 0 -->
  <control>
    <name>ec_spi</name>
    <doc>Enable power to DUT for programming EC SPI Flash</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="0" map="onoff_i"></params>
  </control>
  <control>
    <name>tp24</name>
    <doc>tp24 on U43 pin 5</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="1" map="onoff"></params>
  </control>
  <control>
    <name>tp30</name>
    <doc>tp30 on U43 pin 6</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="2" map="onoff"></params>
  </control>
  <control>
    <name>tp28</name>
    <doc>tp28 on U43 pin 7</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="3" map="onoff"></params>
  </control>
  <control>
    <name>prtctl4_ocs</name>
    <doc>USB port 4 (J3, USB key) over current signal (OCS)</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="6" map="onoff_i"></params>
  </control>
  <control>
    <name>tp27</name>
    <doc>tp27 on U43 pin 11</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="0"
    offset="7" map="onoff"></params>
  </control>
  <!-- slv 0x22 : ioexpander port 1 -->
  <control>
    <name>tp36</name>
    <doc>tp36 on U43 pin 13</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="0" map="onoff"></params>
  </control>
  <control>
    <name>tp35</name>
    <doc>tp35 on U43 pin 14</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="1" map="onoff"></params>
  </control>
  <control>
    <name>tp34</name>
    <doc>tp34 on U43 pin 15</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="2" map="onoff"></params>
  </control>
  <control>
    <name>tp38</name>
    <doc>tp38 on U43 pin 16</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="3" map="onoff"></params>
  </control>
  <control>
    <name>tp39</name>
    <doc>tp39 on U43 pin 17</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="4" map="onoff"></params>
  </control>
  <control>
    <name>dut_hub_ocs</name>
    <doc>DUT USB hub over current signal (OCS). This hub supports
    ethernet (RJ45/I54) and USB port (vert TYPE A/J8)</doc>
    <params interface="2" drv="tca6416" slv="0x22" port="1"
    offset="6" map="onoff_i"></params>
  </control>
  <control>
    <name>sd_en</name>
    <doc>Enable for SD Card detect</doc>
    <params cmd="set" interface="2" drv="tca6416" slv="0x22"
    port="1" offset="7" map="onoff"></params>
  </control>
  <!-- slv 0x23 : ioexpander port 0 -->
  <control>
    <name>spi1_buf_en</name>
    <doc>spi1_buf_en</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="0" map="onoff_i"></params>
  </control>
  <control>
    <name>spi2_buf_en</name>
    <doc>spi2_buf_en</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="1" map="onoff_i"></params>
  </control>
  <control>
    <name>at_hwb</name>
    <doc>at_hwb</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="2" map="onoff_i"></params>
  </control>
  <control>
    <name>tp23</name>
    <doc>tp23 on U38 pin 7</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="3" map="onoff"></params>
  </control>
  <control>
    <name>kbd_m2_a1</name>
    <doc>kbd_m2_a1</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="4" map="onoff"></params>
  </control>
  <control>
    <name>kbd_en</name>
    <doc>Enable servo to assert certain keypresses via kdb_m1 and
    kbd_m2</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="5" map="onoff" init="off"></params>
  </control>
  <control>
    <name>dut_usb2_ocs</name>
    <doc>Over-current signal for USB port (TYPE A/J4) to DUT via
    USB port (TYPE MICRO-B/J5)</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="6" map="onoff_i"></params>
  </control>
  <control>
    <name>usb_mux_oe4</name>
    <doc>usb_mux_oe4</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="0"
    offset="7" map="onoff_i"></params>
  </control>
  <!-- slv 0x23 : ioexpander port 1 -->
  <control>
    <name>kbd_m1_a0</name>
    <doc>kbd_m1_a0</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="0" map="onoff"></params>
  </control>
  <control>
    <name>prtctl3_pwren</name>
    <doc>USB port 3 (TYPE A/J10) power enable</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="1" map="onoff"></params>
  </control>
  <control>
    <name>prtctl2_pwren</name>
    <doc>USB port 2 (TYPE A/J9) power enable</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="2" map="onoff"></params>
  </control>
  <control>
    <name>prtctl2_ocs</name>
    <doc>USB port 2 (TYPE A/J9) over current signal (OCS)</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="3" map="onoff_i"></params>
  </control>
  <control>
    <name>prtctl3_ocs</name>
    <doc>USB port 3 (TYPE A/J10) over current signal (OCS)</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="4" map="onoff_i"></params>
  </control>
  <control>
    <name>kbd_m1_a1</name>
    <doc>kbd_m1_a1</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="5" map="onoff"></params>
  </control>
  <control>
    <name>kbd_m2_a0</name>
    <doc>kbd_m2_a0</doc>
    <params interface="2" drv="tca6416" slv="0x23" port="1"
    offset="6" map="onoff"></params>
  </control>
  <!-- slv 0x24 : ioexpander port 0 -->
  <control>
    <name>spi1_vref</name>
    <doc>spi1_vref</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="0" width="2" map="vref_sel" init="off"></params>
  </control>
  <control>
    <name>tp16</name>
    <doc>tp16 on U30 pin 6</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="2" map="onoff"></params>
  </control>
  <control>
    <name>spi2_vref</name>
    <doc>spi2_vref</doc>
    <alias>fw_wp_vref</alias>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="3" width="2" map="vref_sel" init="off"></params>
  </control>
  <control>
    <name>tp17</name>
    <doc>tp17 on U30 pin 9</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="5" map="onoff"></params>
  </control>
  <control>
    <name>uart2_en</name>
    <alias>cpu_uart_en</alias>
    <doc>Enable communication with CPU's uart console</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="6" map="onoff_i" init="on"></params>
  </control>
  <control>
    <name>uart1_en</name>
    <alias>ec_uart_en</alias>
    <doc>Enable communication with EC's uart console</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="0"
    offset="7" map="onoff_i" init="on"></params>
  </control>
  <!-- slv 0x24 : ioexpander port 1 -->
  <control>
    <name>jtag_buf_en</name>
    <doc>jtag_buf_en</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="0" map="onoff_i" init="off"></params>
  </control>
  <control>
    <name>fw_wp_en</name>
    <doc>Enables forwarding of write-protect gpio. Must assert this
    and set fw_wp_vref prior to changing fw_wp.</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="1" map="onoff" init="off"></params>
  </control>
  <control>
    <name>atmega_rst</name>
    <doc>atmega_rst</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="3" map="onoff_i"></params>
  </control>
  <control>
    <name>at_buf_en</name>
    <doc>at_buf_en</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="4" map="onoff_i"></params>
  </control>
  <control>
    <name>sd_vref_sel</name>
    <doc>sd_vref_sel</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="5" width="2" map="vref_sel" init="off"></params>
  </control>
  <control>
    <name>usb_mux_sel4</name>
    <doc>usb_mux_sel4</doc>
    <params interface="2" drv="tca6416" slv="0x24" port="1"
    offset="7" map="onoff"></params>
  </control>
  <!-- *********** FT4232H U56 Interface 5 ********** -->
  <!-- SPI -->
  <!-- *********** FT4232H U56 Interface 6 ********** -->
  <!-- SPI -->
  <!-- *********** FT4232H U56 Interface 7 ********** -->
  <!-- UART -->
  <control>
    <name>uart1_pty</name>
    <alias>raw_ec_uart_pty</alias>
    <doc>Psuedo-terminal (pty) thats connnected to EC's uart
    console</doc>
    <params cmd="get" subtype="pty" interface="7" drv="uart">
    </params>
  </control>
  <control>
    <name>uart1_baudrate</name>
    <alias>ec_uart_baudrate</alias>
    <doc>Baudrate for EC's uart console</doc>
    <params drv="uart" subtype="props" line_prop="baudrate"
    interface="7"></params>
  </control>
  <control>
    <name>uart1_parity</name>
    <alias>ec_uart_parity</alias>
    <doc>Parity for EC's uart console</doc>
    <params drv="uart" subtype="props" line_prop="parity"
    interface="7" map="uart_parity"></params>
  </control>
  <control>
    <name>uart1_sbits</name>
    <alias>ec_uart_sbits</alias>
    <doc>Number of stop bits for EC's uart console</doc>
    <params drv="uart" subtype="props" line_prop="sbits"
    interface="7" map="uart_sbits"></params>
  </control>
  <control>
    <name>uart1_bits</name>
    <alias>ec_uart_bits</alias>
    <doc>Numbe of data bits for EC's uart console</doc>
    <params drv="uart" subtype="props" line_prop="bits"
    interface="7" map="uart_bits"></params>
  </control>
  <!-- *********** FT4232H U56 Interface 8 ********** -->
  <!-- UART -->
  <control>
    <name>uart2_pty</name>
    <alias>cpu_uart_pty</alias>
    <doc>Psuedo-terminal (pty) thats connnected to CPU's uart
    console</doc>
    <params cmd="get" subtype="pty" interface="8" drv="uart">
    </params>
  </control>
  <control>
    <name>uart2_baudrate</name>
    <alias>cpu_uart_baudrate</alias>
    <doc>Baudrate for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="baudrate"
    interface="8"></params>
  </control>
  <control>
    <name>uart2_parity</name>
    <alias>cpu_uart_parity</alias>
    <doc>Parity for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="parity"
    interface="8" map="uart_parity"></params>
  </control>
  <control>
    <name>uart2_sbits</name>
    <alias>cpu_uart_sbits</alias>
    <doc>Number of stop bits for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="sbits"
    interface="8" map="uart_sbits"></params>
  </control>
  <control>
    <name>uart2_bits</name>
    <alias>cpu_uart_bits</alias>
    <doc>Number of data bits for CPU's uart console</doc>
    <params drv="uart" subtype="props" line_prop="bits"
    interface="8" map="uart_bits"></params>
  </control>
  <!-- EC-3PO console interpreter for main EC -->
  <control>
    <name>ec3po_ec_console</name>
    <alias>ec_uart_pty</alias>
    <doc>EC UART console provided via EC-3PO console interpreter.</doc>
    <params cmd="get" subtype="pty" interface="10" drv="uart"></params>
  </control>
  <control>
    <name>ec_ec3po_interp_connect</name>
    <doc>State indicating if interpreter is listening to the EC UART.</doc>
    <params interface="10" drv="ec3po_driver" map="onoff" init="on"
    subtype="interp_connect"></params>
  </control>
  <control>
    <name>ec_loglevel</name>
    <doc>EC console loglevel</doc>
    <params interface="10" drv="ec3po_driver" input_type="str"
    subtype="loglevel"></params>
  </control>
  <control>
    <name>fw_wp_state</name>
    <doc>Used to turn fw wp off and on</doc>
    <params interface="servo" drv="fw_wp_servoflex" input_type="str"
    fw_wp_vref="pp1800"/>
  </control>
</root>