===============================================================================
			U S E R  M A N U A L

 Copyright (C) 2003-2008, Marvell International Ltd. 

 This software file (the "File") is distributed by Marvell International 
 Ltd. under the terms of the GNU General Public License Version 2, June 1991 
 (the "License").  You may use, redistribute and/or modify this File in 
 accordance with the terms and conditions of the License, a copy of which 
 is available along with the File in the gpl.txt file or by writing to 
 the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 
 02111-1307 or on the worldwide web at http://www.gnu.org/licenses/gpl.txt.

 THE FILE IS DISTRIBUTED AS-IS, WITHOUT WARRANTY OF ANY KIND, AND THE 
 IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE 
 ARE EXPRESSLY DISCLAIMED.  The License provides additional details about 
 this warranty disclaimer.

===============================================================================

1) FOR DRIVER BUILD

	Goto source code directory src_xxxx.
		make [clean] build
	The driver binaries can be found in ../bin_xxxx_bt directory.

2) FOR DRIVER INSTALL

	a) Copy sd8790.bin | sd8787.bin | ... to /lib/firmware/mrvl/ directory, 
	   create the directory if it doesn't exist.
	b) Install bluetooth driver,
		insmod bt8688.ko | bt8790.ko | ...
	c) Uninstall bluetooth driver and sdio bus driver,
		hciconfig hciX down
		rmmod bt8xxx

3) cat /proc/mbt/hcix/config
   This command is used to get the current driver settings. 

4) cat /proc/mbt/hcix/status
   This command is used to get driver status

5) proc commands to config bluetooth parameters. 

drvdbg=[n]
   This command is used to set the bit masks of driver debug message control.

   	bit 0:  MSG  		PRINTM(MSG,...)
	bit 1:  FATAL		PRINTM(FATAL,...)
	bit 2:  ERROR		PRINTM(ERROR,...)
	bit 3:  CMD  		PRINTM(CMD,...)
	bit 27: DATA 		DBG_HEXDUMP(DBG_DATA,...)
	bit 28: ENTRY		PRINTM(ENTRY,...), ENTER(), LEAVE()
	bit 29: WARN 		PRINTM(WARN,...)
	bit 30: INFO 		PRINTM(INFO,...)

	Usage:
		echo "drvdbg=0x7" > /proc/mbt/hcix/config		#enable MSG,FATAL,ERROR messages

gpio_gap=[n]
   This command is used to configure the host sleep parameters.
	bit 8:0  -- Gap
	bit 16:8 -- GPIO

	where GPIO is the pin number of GPIO used to wakeup the host. It could be any valid
		GPIO pin# (e.g. 0-7) or 0xff (Interface, e.g. SDIO will be used instead).
		
	where Gap is the gap in milli seconds between wakeup signal and wakeup event 
		or 0xff for special setting.
	Usage:
		echo "gpio_gap=0xff80" > /proc/mbt/hcix/config   	# use Interface (e.g. SDIO)
		echo "hscfgcmd=1" > /proc/mbt/hcix/config		# gap = 0x80

		echo "gpio_gap=0x03ff" > /proc/mbt/hcix/config   	# use gpio 3
		echo "hscfgcmd=1" > /proc/mbt/hcix/config		# and special host sleep mode

psmode=[n]
    This command is used to enable/disable auto sleep mode
	
	where the option is:
			1 	-- Enable auto sleep mode
			0 	-- Disable auto sleep mode
	Usage:
		echo "psmode=1" > /proc/mbt/hcix/config			#enable power save mode
		echo "pscmd=1" > /proc/mbt/hcix/config

		echo "psmode=0" > /proc/mbt/hcix/config			#disable power save mode
		echo "pscmd=1" > /proc/mbt/hcix/config
		
						

6)Use hcitool to issue raw hci command, refer to hcitool manual

	Usage: Hcitool cmd <ogf> <ocf> [Parameters]

	1.Interface Control Command
	  hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00    --Enable All interface
	  hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01    --Enable Wlan interface
	  hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02    --Enable BT interface
	  hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00    --Disable All interface
	  hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01    --Disable Wlan interface
	  hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02    --Disable BT interface		

==============================================================================