| /** |
| ****************************************************************************** |
| * @file stm32h7xx_hal_sd.h |
| * @author MCD Application Team |
| * @brief Header file of SD HAL module. |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Define to prevent recursive inclusion -------------------------------------*/ |
| #ifndef STM32H7xx_HAL_SD_H |
| #define STM32H7xx_HAL_SD_H |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32h7xx_ll_sdmmc.h" |
| #if defined (DLYB_SDMMC1) || defined (DLYB_SDMMC2) || defined (DLYB_SDMMC3) |
| #include "stm32h7xx_ll_delayblock.h" |
| #endif /* (DLYB_SDMMC1) || (DLYB_SDMMC2) */ |
| |
| /** @addtogroup STM32H7xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup SD SD |
| * @brief SD HAL module driver |
| * @{ |
| */ |
| |
| /* Exported types ------------------------------------------------------------*/ |
| /** @defgroup SD_Exported_Types SD Exported Types |
| * @{ |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group1 SD State enumeration structure |
| * @{ |
| */ |
| typedef enum |
| { |
| HAL_SD_STATE_RESET = ((uint32_t)0x00000000U), /*!< SD not yet initialized or disabled */ |
| HAL_SD_STATE_READY = ((uint32_t)0x00000001U), /*!< SD initialized and ready for use */ |
| HAL_SD_STATE_TIMEOUT = ((uint32_t)0x00000002U), /*!< SD Timeout state */ |
| HAL_SD_STATE_BUSY = ((uint32_t)0x00000003U), /*!< SD process ongoing */ |
| HAL_SD_STATE_PROGRAMMING = ((uint32_t)0x00000004U), /*!< SD Programming State */ |
| HAL_SD_STATE_RECEIVING = ((uint32_t)0x00000005U), /*!< SD Receiving State */ |
| HAL_SD_STATE_TRANSFER = ((uint32_t)0x00000006U), /*!< SD Transfert State */ |
| HAL_SD_STATE_ERROR = ((uint32_t)0x0000000FU) /*!< SD is in error state */ |
| }HAL_SD_StateTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group2 SD Card State enumeration structure |
| * @{ |
| */ |
| typedef uint32_t HAL_SD_CardStateTypeDef; |
| |
| #define HAL_SD_CARD_READY 0x00000001U /*!< Card state is ready */ |
| #define HAL_SD_CARD_IDENTIFICATION 0x00000002U /*!< Card is in identification state */ |
| #define HAL_SD_CARD_STANDBY 0x00000003U /*!< Card is in standby state */ |
| #define HAL_SD_CARD_TRANSFER 0x00000004U /*!< Card is in transfer state */ |
| #define HAL_SD_CARD_SENDING 0x00000005U /*!< Card is sending an operation */ |
| #define HAL_SD_CARD_RECEIVING 0x00000006U /*!< Card is receiving operation information */ |
| #define HAL_SD_CARD_PROGRAMMING 0x00000007U /*!< Card is in programming state */ |
| #define HAL_SD_CARD_DISCONNECTED 0x00000008U /*!< Card is disconnected */ |
| #define HAL_SD_CARD_ERROR 0x000000FFU /*!< Card response Error */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group3 SD Handle Structure definition |
| * @{ |
| */ |
| #define SD_InitTypeDef SDMMC_InitTypeDef |
| #define SD_TypeDef SDMMC_TypeDef |
| |
| /** |
| * @brief SD Card Information Structure definition |
| */ |
| typedef struct |
| { |
| uint32_t CardType; /*!< Specifies the card Type */ |
| |
| uint32_t CardVersion; /*!< Specifies the card version */ |
| |
| uint32_t Class; /*!< Specifies the class of the card class */ |
| |
| uint32_t RelCardAdd; /*!< Specifies the Relative Card Address */ |
| |
| uint32_t BlockNbr; /*!< Specifies the Card Capacity in blocks */ |
| |
| uint32_t BlockSize; /*!< Specifies one block size in bytes */ |
| |
| uint32_t LogBlockNbr; /*!< Specifies the Card logical Capacity in blocks */ |
| |
| uint32_t LogBlockSize; /*!< Specifies logical block size in bytes */ |
| |
| uint32_t CardSpeed; /*!< Specifies the card Speed */ |
| |
| }HAL_SD_CardInfoTypeDef; |
| |
| /** |
| * @brief SD handle Structure definition |
| */ |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| typedef struct __SD_HandleTypeDef |
| #else |
| typedef struct |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| { |
| SD_TypeDef *Instance; /*!< SD registers base address */ |
| |
| SD_InitTypeDef Init; /*!< SD required parameters */ |
| |
| HAL_LockTypeDef Lock; /*!< SD locking object */ |
| |
| uint8_t *pTxBuffPtr; /*!< Pointer to SD Tx transfer Buffer */ |
| |
| uint32_t TxXferSize; /*!< SD Tx Transfer size */ |
| |
| uint8_t *pRxBuffPtr; /*!< Pointer to SD Rx transfer Buffer */ |
| |
| uint32_t RxXferSize; /*!< SD Rx Transfer size */ |
| |
| __IO uint32_t Context; /*!< SD transfer context */ |
| |
| __IO HAL_SD_StateTypeDef State; /*!< SD card State */ |
| |
| __IO uint32_t ErrorCode; /*!< SD Card Error codes */ |
| |
| HAL_SD_CardInfoTypeDef SdCard; /*!< SD Card information */ |
| |
| uint32_t CSD[4]; /*!< SD card specific data table */ |
| |
| uint32_t CID[4]; /*!< SD card identification number table */ |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| void (* TxCpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* RxCpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* ErrorCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* AbortCpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* Read_DMADblBuf0CpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* Read_DMADblBuf1CpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* Write_DMADblBuf0CpltCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* Write_DMADblBuf1CpltCallback) (struct __SD_HandleTypeDef *hsd); |
| |
| #if (USE_SD_TRANSCEIVER != 0U) |
| void (* DriveTransceiver_1_8V_Callback) (FlagStatus status); |
| #endif /* USE_SD_TRANSCEIVER */ |
| |
| void (* MspInitCallback) (struct __SD_HandleTypeDef *hsd); |
| void (* MspDeInitCallback) (struct __SD_HandleTypeDef *hsd); |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| }SD_HandleTypeDef; |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group4 Card Specific Data: CSD Register |
| * @{ |
| */ |
| typedef struct |
| { |
| __IO uint8_t CSDStruct; /*!< CSD structure */ |
| __IO uint8_t SysSpecVersion; /*!< System specification version */ |
| __IO uint8_t Reserved1; /*!< Reserved */ |
| __IO uint8_t TAAC; /*!< Data read access time 1 */ |
| __IO uint8_t NSAC; /*!< Data read access time 2 in CLK cycles */ |
| __IO uint8_t MaxBusClkFrec; /*!< Max. bus clock frequency */ |
| __IO uint16_t CardComdClasses; /*!< Card command classes */ |
| __IO uint8_t RdBlockLen; /*!< Max. read data block length */ |
| __IO uint8_t PartBlockRead; /*!< Partial blocks for read allowed */ |
| __IO uint8_t WrBlockMisalign; /*!< Write block misalignment */ |
| __IO uint8_t RdBlockMisalign; /*!< Read block misalignment */ |
| __IO uint8_t DSRImpl; /*!< DSR implemented */ |
| __IO uint8_t Reserved2; /*!< Reserved */ |
| __IO uint32_t DeviceSize; /*!< Device Size */ |
| __IO uint8_t MaxRdCurrentVDDMin; /*!< Max. read current @ VDD min */ |
| __IO uint8_t MaxRdCurrentVDDMax; /*!< Max. read current @ VDD max */ |
| __IO uint8_t MaxWrCurrentVDDMin; /*!< Max. write current @ VDD min */ |
| __IO uint8_t MaxWrCurrentVDDMax; /*!< Max. write current @ VDD max */ |
| __IO uint8_t DeviceSizeMul; /*!< Device size multiplier */ |
| __IO uint8_t EraseGrSize; /*!< Erase group size */ |
| __IO uint8_t EraseGrMul; /*!< Erase group size multiplier */ |
| __IO uint8_t WrProtectGrSize; /*!< Write protect group size */ |
| __IO uint8_t WrProtectGrEnable; /*!< Write protect group enable */ |
| __IO uint8_t ManDeflECC; /*!< Manufacturer default ECC */ |
| __IO uint8_t WrSpeedFact; /*!< Write speed factor */ |
| __IO uint8_t MaxWrBlockLen; /*!< Max. write data block length */ |
| __IO uint8_t WriteBlockPaPartial; /*!< Partial blocks for write allowed */ |
| __IO uint8_t Reserved3; /*!< Reserved */ |
| __IO uint8_t ContentProtectAppli; /*!< Content protection application */ |
| __IO uint8_t FileFormatGroup; /*!< File format group */ |
| __IO uint8_t CopyFlag; /*!< Copy flag (OTP) */ |
| __IO uint8_t PermWrProtect; /*!< Permanent write protection */ |
| __IO uint8_t TempWrProtect; /*!< Temporary write protection */ |
| __IO uint8_t FileFormat; /*!< File format */ |
| __IO uint8_t ECC; /*!< ECC code */ |
| __IO uint8_t CSD_CRC; /*!< CSD CRC */ |
| __IO uint8_t Reserved4; /*!< Always 1 */ |
| }HAL_SD_CardCSDTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group5 Card Identification Data: CID Register |
| * @{ |
| */ |
| typedef struct |
| { |
| __IO uint8_t ManufacturerID; /*!< Manufacturer ID */ |
| __IO uint16_t OEM_AppliID; /*!< OEM/Application ID */ |
| __IO uint32_t ProdName1; /*!< Product Name part1 */ |
| __IO uint8_t ProdName2; /*!< Product Name part2 */ |
| __IO uint8_t ProdRev; /*!< Product Revision */ |
| __IO uint32_t ProdSN; /*!< Product Serial Number */ |
| __IO uint8_t Reserved1; /*!< Reserved1 */ |
| __IO uint16_t ManufactDate; /*!< Manufacturing Date */ |
| __IO uint8_t CID_CRC; /*!< CID CRC */ |
| __IO uint8_t Reserved2; /*!< Always 1 */ |
| |
| }HAL_SD_CardCIDTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group6 SD Card Status returned by ACMD13 |
| * @{ |
| */ |
| typedef struct |
| { |
| __IO uint8_t DataBusWidth; /*!< Shows the currently defined data bus width */ |
| __IO uint8_t SecuredMode; /*!< Card is in secured mode of operation */ |
| __IO uint16_t CardType; /*!< Carries information about card type */ |
| __IO uint32_t ProtectedAreaSize; /*!< Carries information about the capacity of protected area */ |
| __IO uint8_t SpeedClass; /*!< Carries information about the speed class of the card */ |
| __IO uint8_t PerformanceMove; /*!< Carries information about the card's performance move */ |
| __IO uint8_t AllocationUnitSize; /*!< Carries information about the card's allocation unit size */ |
| __IO uint16_t EraseSize; /*!< Determines the number of AUs to be erased in one operation */ |
| __IO uint8_t EraseTimeout; /*!< Determines the timeout for any number of AU erase */ |
| __IO uint8_t EraseOffset; /*!< Carries information about the erase offset */ |
| __IO uint8_t UhsSpeedGrade; /*!< Carries information about the speed grade of UHS card */ |
| __IO uint8_t UhsAllocationUnitSize; /*!< Carries information about the UHS card's allocation unit size */ |
| __IO uint8_t VideoSpeedClass; /*!< Carries information about the Video Speed Class of UHS card */ |
| }HAL_SD_CardStatusTypeDef; |
| /** |
| * @} |
| */ |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| /** @defgroup SD_Exported_Types_Group7 SD Callback ID enumeration definition |
| * @{ |
| */ |
| typedef enum |
| { |
| HAL_SD_TX_CPLT_CB_ID = 0x00U, /*!< SD Tx Complete Callback ID */ |
| HAL_SD_RX_CPLT_CB_ID = 0x01U, /*!< SD Rx Complete Callback ID */ |
| HAL_SD_ERROR_CB_ID = 0x02U, /*!< SD Error Callback ID */ |
| HAL_SD_ABORT_CB_ID = 0x03U, /*!< SD Abort Callback ID */ |
| HAL_SD_READ_DMA_DBL_BUF0_CPLT_CB_ID = 0x04U, /*!< SD Rx DMA Double Buffer 0 Complete Callback ID */ |
| HAL_SD_READ_DMA_DBL_BUF1_CPLT_CB_ID = 0x05U, /*!< SD Rx DMA Double Buffer 1 Complete Callback ID */ |
| HAL_SD_WRITE_DMA_DBL_BUF0_CPLT_CB_ID = 0x06U, /*!< SD Tx DMA Double Buffer 0 Complete Callback ID */ |
| HAL_SD_WRITE_DMA_DBL_BUF1_CPLT_CB_ID = 0x07U, /*!< SD Tx DMA Double Buffer 1 Complete Callback ID */ |
| |
| HAL_SD_MSP_INIT_CB_ID = 0x10U, /*!< SD MspInit Callback ID */ |
| HAL_SD_MSP_DEINIT_CB_ID = 0x11U /*!< SD MspDeInit Callback ID */ |
| }HAL_SD_CallbackIDTypeDef; |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Types_Group8 SD Callback pointer definition |
| * @{ |
| */ |
| typedef void (*pSD_CallbackTypeDef) (SD_HandleTypeDef *hsd); |
| #if (USE_SD_TRANSCEIVER != 0U) |
| typedef void (*pSD_TransceiverCallbackTypeDef)(FlagStatus status); |
| #endif /* USE_SD_TRANSCEIVER */ |
| /** |
| * @} |
| */ |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /* Exported constants --------------------------------------------------------*/ |
| /** @defgroup SD_Exported_Constants Exported Constants |
| * @{ |
| */ |
| |
| #define BLOCKSIZE ((uint32_t)512U) /*!< Block size is 512 bytes */ |
| |
| /** @defgroup SD_Exported_Constansts_Group1 SD Error status enumeration Structure definition |
| * @{ |
| */ |
| #define HAL_SD_ERROR_NONE SDMMC_ERROR_NONE /*!< No error */ |
| #define HAL_SD_ERROR_CMD_CRC_FAIL SDMMC_ERROR_CMD_CRC_FAIL /*!< Command response received (but CRC check failed) */ |
| #define HAL_SD_ERROR_DATA_CRC_FAIL SDMMC_ERROR_DATA_CRC_FAIL /*!< Data block sent/received (CRC check failed) */ |
| #define HAL_SD_ERROR_CMD_RSP_TIMEOUT SDMMC_ERROR_CMD_RSP_TIMEOUT /*!< Command response timeout */ |
| #define HAL_SD_ERROR_DATA_TIMEOUT SDMMC_ERROR_DATA_TIMEOUT /*!< Data timeout */ |
| #define HAL_SD_ERROR_TX_UNDERRUN SDMMC_ERROR_TX_UNDERRUN /*!< Transmit FIFO underrun */ |
| #define HAL_SD_ERROR_RX_OVERRUN SDMMC_ERROR_RX_OVERRUN /*!< Receive FIFO overrun */ |
| #define HAL_SD_ERROR_ADDR_MISALIGNED SDMMC_ERROR_ADDR_MISALIGNED /*!< Misaligned address */ |
| #define HAL_SD_ERROR_BLOCK_LEN_ERR SDMMC_ERROR_BLOCK_LEN_ERR /*!< Transferred block length is not allowed for the card or the |
| number of transferred bytes does not match the block length */ |
| #define HAL_SD_ERROR_ERASE_SEQ_ERR SDMMC_ERROR_ERASE_SEQ_ERR /*!< An error in the sequence of erase command occurs */ |
| #define HAL_SD_ERROR_BAD_ERASE_PARAM SDMMC_ERROR_BAD_ERASE_PARAM /*!< An invalid selection for erase groups */ |
| #define HAL_SD_ERROR_WRITE_PROT_VIOLATION SDMMC_ERROR_WRITE_PROT_VIOLATION /*!< Attempt to program a write protect block */ |
| #define HAL_SD_ERROR_LOCK_UNLOCK_FAILED SDMMC_ERROR_LOCK_UNLOCK_FAILED /*!< Sequence or password error has been detected in unlock |
| command or if there was an attempt to access a locked card */ |
| #define HAL_SD_ERROR_COM_CRC_FAILED SDMMC_ERROR_COM_CRC_FAILED /*!< CRC check of the previous command failed */ |
| #define HAL_SD_ERROR_ILLEGAL_CMD SDMMC_ERROR_ILLEGAL_CMD /*!< Command is not legal for the card state */ |
| #define HAL_SD_ERROR_CARD_ECC_FAILED SDMMC_ERROR_CARD_ECC_FAILED /*!< Card internal ECC was applied but failed to correct the data */ |
| #define HAL_SD_ERROR_CC_ERR SDMMC_ERROR_CC_ERR /*!< Internal card controller error */ |
| #define HAL_SD_ERROR_GENERAL_UNKNOWN_ERR SDMMC_ERROR_GENERAL_UNKNOWN_ERR /*!< General or unknown error */ |
| #define HAL_SD_ERROR_STREAM_READ_UNDERRUN SDMMC_ERROR_STREAM_READ_UNDERRUN /*!< The card could not sustain data reading in stream rmode */ |
| #define HAL_SD_ERROR_STREAM_WRITE_OVERRUN SDMMC_ERROR_STREAM_WRITE_OVERRUN /*!< The card could not sustain data programming in stream mode */ |
| #define HAL_SD_ERROR_CID_CSD_OVERWRITE SDMMC_ERROR_CID_CSD_OVERWRITE /*!< CID/CSD overwrite error */ |
| #define HAL_SD_ERROR_WP_ERASE_SKIP SDMMC_ERROR_WP_ERASE_SKIP /*!< Only partial address space was erased */ |
| #define HAL_SD_ERROR_CARD_ECC_DISABLED SDMMC_ERROR_CARD_ECC_DISABLED /*!< Command has been executed without using internal ECC */ |
| #define HAL_SD_ERROR_ERASE_RESET SDMMC_ERROR_ERASE_RESET /*!< Erase sequence was cleared before executing because an out |
| of erase sequence command was received */ |
| #define HAL_SD_ERROR_AKE_SEQ_ERR SDMMC_ERROR_AKE_SEQ_ERR /*!< Error in sequence of authentication */ |
| #define HAL_SD_ERROR_INVALID_VOLTRANGE SDMMC_ERROR_INVALID_VOLTRANGE /*!< Error in case of invalid voltage range */ |
| #define HAL_SD_ERROR_ADDR_OUT_OF_RANGE SDMMC_ERROR_ADDR_OUT_OF_RANGE /*!< Error when addressed block is out of range */ |
| #define HAL_SD_ERROR_REQUEST_NOT_APPLICABLE SDMMC_ERROR_REQUEST_NOT_APPLICABLE /*!< Error when command request is not applicable */ |
| #define HAL_SD_ERROR_PARAM SDMMC_ERROR_INVALID_PARAMETER /*!< the used parameter is not valid */ |
| #define HAL_SD_ERROR_UNSUPPORTED_FEATURE SDMMC_ERROR_UNSUPPORTED_FEATURE /*!< Error when feature is not insupported */ |
| #define HAL_SD_ERROR_BUSY SDMMC_ERROR_BUSY /*!< Error when transfer process is busy */ |
| #define HAL_SD_ERROR_DMA SDMMC_ERROR_DMA /*!< Error while DMA transfer */ |
| #define HAL_SD_ERROR_TIMEOUT SDMMC_ERROR_TIMEOUT /*!< Timeout error */ |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| #define HAL_SD_ERROR_INVALID_CALLBACK SDMMC_ERROR_INVALID_PARAMETER /*!< Invalid callback error */ |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Constansts_Group2 SD context enumeration |
| * @{ |
| */ |
| #define SD_CONTEXT_NONE ((uint32_t)0x00000000U) /*!< None */ |
| #define SD_CONTEXT_READ_SINGLE_BLOCK ((uint32_t)0x00000001U) /*!< Read single block operation */ |
| #define SD_CONTEXT_READ_MULTIPLE_BLOCK ((uint32_t)0x00000002U) /*!< Read multiple blocks operation */ |
| #define SD_CONTEXT_WRITE_SINGLE_BLOCK ((uint32_t)0x00000010U) /*!< Write single block operation */ |
| #define SD_CONTEXT_WRITE_MULTIPLE_BLOCK ((uint32_t)0x00000020U) /*!< Write multiple blocks operation */ |
| #define SD_CONTEXT_IT ((uint32_t)0x00000008U) /*!< Process in Interrupt mode */ |
| #define SD_CONTEXT_DMA ((uint32_t)0x00000080U) /*!< Process in DMA mode */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Constansts_Group3 SD Supported Memory Cards |
| * @{ |
| */ |
| #define CARD_NORMAL_SPEED ((uint32_t)0x00000000U) /*!< Normal Speed Card <12.5Mo/s , Spec Version 1.01 */ |
| #define CARD_HIGH_SPEED ((uint32_t)0x00000100U) /*!< High Speed Card <25Mo/s , Spec version 2.00 */ |
| #define CARD_ULTRA_HIGH_SPEED ((uint32_t)0x00000200U) /*!< UHS-I SD Card <50Mo/s for SDR50, DDR5 Cards |
| and <104Mo/s for SDR104, Spec version 3.01 */ |
| |
| #define CARD_SDSC ((uint32_t)0x00000000U) /*!< SD Standard Capacity <2Go */ |
| #define CARD_SDHC_SDXC ((uint32_t)0x00000001U) /*!< SD High Capacity <32Go, SD Extended Capacity <2To */ |
| #define CARD_SECURED ((uint32_t)0x00000003U) |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Constansts_Group4 SD Supported Version |
| * @{ |
| */ |
| #define CARD_V1_X ((uint32_t)0x00000000U) |
| #define CARD_V2_X ((uint32_t)0x00000001U) |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported macro ------------------------------------------------------------*/ |
| /** @defgroup SD_Exported_macros SD Exported Macros |
| * @brief macros to handle interrupts and specific clock configurations |
| * @{ |
| */ |
| /** @brief Reset SD handle state. |
| * @param __HANDLE__ SD Handle. |
| * @retval None |
| */ |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| #define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__) do { \ |
| (__HANDLE__)->State = HAL_SD_STATE_RESET; \ |
| (__HANDLE__)->MspInitCallback = NULL; \ |
| (__HANDLE__)->MspDeInitCallback = NULL; \ |
| } while(0) |
| #else |
| #define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SD_STATE_RESET) |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| |
| /** |
| * @brief Enable the SD device interrupt. |
| * @param __HANDLE__ SD Handle. |
| * @param __INTERRUPT__ specifies the SDMMC interrupt sources to be enabled. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt |
| * @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt |
| * @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt |
| * @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt |
| * @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt |
| * @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt |
| * @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt |
| * @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt |
| * @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt |
| * @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt |
| * @retval None |
| */ |
| #define __HAL_SD_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDMMC_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) |
| |
| /** |
| * @brief Disable the SD device interrupt. |
| * @param __HANDLE__ SD Handle. |
| * @param __INTERRUPT__ specifies the SDMMC interrupt sources to be disabled. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt |
| * @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt |
| * @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt |
| * @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt |
| * @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt |
| * @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt |
| * @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt |
| * @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt |
| * @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt |
| * @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt |
| * @retval None |
| */ |
| #define __HAL_SD_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDMMC_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__)) |
| |
| /** |
| * @brief Check whether the specified SD flag is set or not. |
| * @param __HANDLE__ SD Handle. |
| * @param __FLAG__ specifies the flag to check. |
| * This parameter can be one of the following values: |
| * @arg SDMMC_FLAG_CCRCFAIL: Command response received (CRC check failed) |
| * @arg SDMMC_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) |
| * @arg SDMMC_FLAG_CTIMEOUT: Command response timeout |
| * @arg SDMMC_FLAG_DTIMEOUT: Data timeout |
| * @arg SDMMC_FLAG_TXUNDERR: Transmit FIFO underrun error |
| * @arg SDMMC_FLAG_RXOVERR: Received FIFO overrun error |
| * @arg SDMMC_FLAG_CMDREND: Command response received (CRC check passed) |
| * @arg SDMMC_FLAG_CMDSENT: Command sent (no response required) |
| * @arg SDMMC_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero) |
| * @arg SDMMC_FLAG_DHOLD: Data transfer Hold |
| * @arg SDMMC_FLAG_DBCKEND: Data block sent/received (CRC check passed) |
| * @arg SDMMC_FLAG_DABORT: Data transfer aborted by CMD12 |
| * @arg SDMMC_FLAG_DPSMACT: Data path state machine active |
| * @arg SDMMC_FLAG_CPSMACT: Command path state machine active |
| * @arg SDMMC_FLAG_TXFIFOHE: Transmit FIFO Half Empty |
| * @arg SDMMC_FLAG_RXFIFOHF: Receive FIFO Half Full |
| * @arg SDMMC_FLAG_TXFIFOF: Transmit FIFO full |
| * @arg SDMMC_FLAG_RXFIFOF: Receive FIFO full |
| * @arg SDMMC_FLAG_TXFIFOE: Transmit FIFO empty |
| * @arg SDMMC_FLAG_RXFIFOE: Receive FIFO empty |
| * @arg SDMMC_FLAG_BUSYD0: Inverted value of SDMMC_D0 line (Busy) |
| * @arg SDMMC_FLAG_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected |
| * @arg SDMMC_FLAG_SDIOIT: SDIO interrupt received |
| * @arg SDMMC_FLAG_ACKFAIL: Boot Acknowledgment received |
| * @arg SDMMC_FLAG_ACKTIMEOUT: Boot Acknowledgment timeout |
| * @arg SDMMC_FLAG_VSWEND: Voltage switch critical timing section completion |
| * @arg SDMMC_FLAG_CKSTOP: SDMMC_CK stopped in Voltage switch procedure |
| * @arg SDMMC_FLAG_IDMATE: IDMA transfer error |
| * @arg SDMMC_FLAG_IDMABTC: IDMA buffer transfer complete |
| * @retval The new state of SD FLAG (SET or RESET). |
| */ |
| #define __HAL_SD_GET_FLAG(__HANDLE__, __FLAG__) __SDMMC_GET_FLAG((__HANDLE__)->Instance, (__FLAG__)) |
| |
| /** |
| * @brief Clear the SD's pending flags. |
| * @param __HANDLE__ SD Handle. |
| * @param __FLAG__ specifies the flag to clear. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDMMC_FLAG_CCRCFAIL: Command response received (CRC check failed) |
| * @arg SDMMC_FLAG_DCRCFAIL: Data block sent/received (CRC check failed) |
| * @arg SDMMC_FLAG_CTIMEOUT: Command response timeout |
| * @arg SDMMC_FLAG_DTIMEOUT: Data timeout |
| * @arg SDMMC_FLAG_TXUNDERR: Transmit FIFO underrun error |
| * @arg SDMMC_FLAG_RXOVERR: Received FIFO overrun error |
| * @arg SDMMC_FLAG_CMDREND: Command response received (CRC check passed) |
| * @arg SDMMC_FLAG_CMDSENT: Command sent (no response required) |
| * @arg SDMMC_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero) |
| * @arg SDMMC_FLAG_DHOLD: Data transfer Hold |
| * @arg SDMMC_FLAG_DBCKEND: Data block sent/received (CRC check passed) |
| * @arg SDMMC_FLAG_DABORT: Data transfer aborted by CMD12 |
| * @arg SDMMC_FLAG_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected |
| * @arg SDMMC_FLAG_SDIOIT: SDIO interrupt received |
| * @arg SDMMC_FLAG_ACKFAIL: Boot Acknowledgment received |
| * @arg SDMMC_FLAG_ACKTIMEOUT: Boot Acknowledgment timeout |
| * @arg SDMMC_FLAG_VSWEND: Voltage switch critical timing section completion |
| * @arg SDMMC_FLAG_CKSTOP: SDMMC_CK stopped in Voltage switch procedure |
| * @arg SDMMC_FLAG_IDMATE: IDMA transfer error |
| * @arg SDMMC_FLAG_IDMABTC: IDMA buffer transfer complete |
| * @retval None |
| */ |
| #define __HAL_SD_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDMMC_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__)) |
| |
| /** |
| * @brief Check whether the specified SD interrupt has occurred or not. |
| * @param __HANDLE__ SD Handle. |
| * @param __INTERRUPT__ specifies the SDMMC interrupt source to check. |
| * This parameter can be one of the following values: |
| * @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt |
| * @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt |
| * @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt |
| * @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt |
| * @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt |
| * @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt |
| * @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt |
| * @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt |
| * @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt |
| * @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt |
| * @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt |
| * @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt |
| * @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt |
| * @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt |
| * @retval The new state of SD IT (SET or RESET). |
| */ |
| #define __HAL_SD_GET_IT(__HANDLE__, __INTERRUPT__) __SDMMC_GET_IT((__HANDLE__)->Instance, (__INTERRUPT__)) |
| |
| /** |
| * @brief Clear the SD's interrupt pending bits. |
| * @param __HANDLE__ SD Handle. |
| * @param __INTERRUPT__ specifies the interrupt pending bit to clear. |
| * This parameter can be one or a combination of the following values: |
| * @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt |
| * @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt |
| * @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt |
| * @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt |
| * @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt |
| * @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt |
| * @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt |
| * @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt |
| * @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt |
| * @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt |
| * @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt |
| * @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt |
| * @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt |
| * @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt |
| * @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt |
| * @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt |
| * @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt |
| * @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt |
| * @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt |
| * @retval None |
| */ |
| #define __HAL_SD_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDMMC_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__)) |
| |
| /** |
| * @} |
| */ |
| |
| /* Include SD HAL Extension module */ |
| #include "stm32h7xx_hal_sd_ex.h" |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @defgroup SD_Exported_Functions SD Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_SD_Init (SD_HandleTypeDef *hsd); |
| HAL_StatusTypeDef HAL_SD_InitCard (SD_HandleTypeDef *hsd); |
| HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd); |
| void HAL_SD_MspInit (SD_HandleTypeDef *hsd); |
| void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group2 Input and Output operation functions |
| * @{ |
| */ |
| /* Blocking mode: Polling */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks (SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_SD_WriteBlocks (SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout); |
| HAL_StatusTypeDef HAL_SD_Erase (SD_HandleTypeDef *hsd, uint32_t BlockStartAdd, uint32_t BlockEndAdd); |
| /* Non-Blocking mode: IT */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks_IT (SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks); |
| HAL_StatusTypeDef HAL_SD_WriteBlocks_IT (SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks); |
| /* Non-Blocking mode: DMA */ |
| HAL_StatusTypeDef HAL_SD_ReadBlocks_DMA (SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks); |
| HAL_StatusTypeDef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks); |
| |
| void HAL_SD_IRQHandler (SD_HandleTypeDef *hsd); |
| |
| /* Callback in non blocking modes (DMA) */ |
| void HAL_SD_TxCpltCallback (SD_HandleTypeDef *hsd); |
| void HAL_SD_RxCpltCallback (SD_HandleTypeDef *hsd); |
| void HAL_SD_ErrorCallback (SD_HandleTypeDef *hsd); |
| void HAL_SD_AbortCallback (SD_HandleTypeDef *hsd); |
| |
| #if (USE_SD_TRANSCEIVER != 0U) |
| /* Callback to switch in 1.8V mode */ |
| void HAL_SD_DriveTransceiver_1_8V_Callback(FlagStatus status); |
| #endif /* USE_SD_TRANSCEIVER */ |
| |
| #if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U) |
| /* SD callback registering/unregistering */ |
| HAL_StatusTypeDef HAL_SD_RegisterCallback (SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID, pSD_CallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_SD_UnRegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackID); |
| |
| #if (USE_SD_TRANSCEIVER != 0U) |
| HAL_StatusTypeDef HAL_SD_RegisterTransceiverCallback (SD_HandleTypeDef *hsd, pSD_TransceiverCallbackTypeDef pCallback); |
| HAL_StatusTypeDef HAL_SD_UnRegisterTransceiverCallback(SD_HandleTypeDef *hsd); |
| #endif /* USE_SD_TRANSCEIVER */ |
| #endif /* USE_HAL_SD_REGISTER_CALLBACKS */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group3 Peripheral Control functions |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_SD_ConfigWideBusOperation(SD_HandleTypeDef *hsd, uint32_t WideMode); |
| HAL_StatusTypeDef HAL_SD_ConfigSpeedBusOperation(SD_HandleTypeDef *hsd, uint32_t SpeedMode); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group4 SD card related functions |
| * @{ |
| */ |
| HAL_SD_CardStateTypeDef HAL_SD_GetCardState(SD_HandleTypeDef *hsd); |
| HAL_StatusTypeDef HAL_SD_GetCardCID (SD_HandleTypeDef *hsd, HAL_SD_CardCIDTypeDef *pCID); |
| HAL_StatusTypeDef HAL_SD_GetCardCSD (SD_HandleTypeDef *hsd, HAL_SD_CardCSDTypeDef *pCSD); |
| HAL_StatusTypeDef HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypeDef *pStatus); |
| HAL_StatusTypeDef HAL_SD_GetCardInfo (SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypeDef *pCardInfo); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group5 Peripheral State and Errors functions |
| * @{ |
| */ |
| HAL_SD_StateTypeDef HAL_SD_GetState(SD_HandleTypeDef *hsd); |
| uint32_t HAL_SD_GetError(SD_HandleTypeDef *hsd); |
| /** |
| * @} |
| */ |
| |
| /** @defgroup SD_Exported_Functions_Group6 Perioheral Abort management |
| * @{ |
| */ |
| HAL_StatusTypeDef HAL_SD_Abort (SD_HandleTypeDef *hsd); |
| HAL_StatusTypeDef HAL_SD_Abort_IT(SD_HandleTypeDef *hsd); |
| /** |
| * @} |
| */ |
| |
| /* Private types -------------------------------------------------------------*/ |
| /** @defgroup SD_Private_Types SD Private Types |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private defines -----------------------------------------------------------*/ |
| /** @defgroup SD_Private_Defines SD Private Defines |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private variables ---------------------------------------------------------*/ |
| /** @defgroup SD_Private_Variables SD Private Variables |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private constants ---------------------------------------------------------*/ |
| /** @defgroup SD_Private_Constants SD Private Constants |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /** @defgroup SD_Private_Macros SD Private Macros |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private functions prototypes ----------------------------------------------*/ |
| /** @defgroup SD_Private_Functions_Prototypes SD Private Functions Prototypes |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /* Private functions ---------------------------------------------------------*/ |
| /** @defgroup SD_Private_Functions SD Private Functions |
| * @{ |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| |
| #endif /* STM32H7xx_HAL_SD_H */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
