| # Copyright 1999-2012 Free Software Foundation, Inc. |
| |
| # This program is free software; you can redistribute it and/or modify |
| # it under the terms of the GNU General Public License as published by |
| # the Free Software Foundation; either version 3 of the License, or |
| # (at your option) any later version. |
| # |
| # This program is distributed in the hope that it will be useful, |
| # but WITHOUT ANY WARRANTY; without even the implied warranty of |
| # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| # GNU General Public License for more details. |
| # |
| # You should have received a copy of the GNU General Public License |
| # along with this program. If not, see <http://www.gnu.org/licenses/>. |
| |
| # This file was written by Elena Zannoni (ezannoni@cygnus.com) |
| |
| |
| # are we on a target board? If so, don't run these tests. |
| # note: this is necessary because we cannot use runto_main (which would |
| # work for remote targets too) because of the different prompt we get |
| # when using annotation level 2. |
| # |
| if [is_remote target] then { |
| return 0 |
| } |
| |
| |
| # |
| # test running programs |
| # |
| |
| set testfile "annota1" |
| set srcfile ${testfile}.c |
| set binfile ${objdir}/${subdir}/${testfile} |
| |
| if { [gdb_compile "${srcdir}/${subdir}/${srcfile}" "${binfile}" executable {debug nowarnings}] != "" } { |
| untested annota1.exp |
| return -1 |
| } |
| |
| |
| gdb_exit |
| gdb_start |
| gdb_reinitialize_dir $srcdir/$subdir |
| gdb_load ${binfile} |
| |
| # The commands we test here produce many lines of output; disable "press |
| # <return> to continue" prompts. |
| gdb_test_no_output "set height 0" |
| |
| # |
| # break at main |
| # |
| |
| set main_line [gdb_get_line_number "break main"] |
| |
| gdb_test "break main" \ |
| "Breakpoint.*at.* file .*$srcfile, line $main_line\\." \ |
| "breakpoint main" |
| |
| |
| # |
| # NOTE: this prompt is OK only when the annotation level is > 1 |
| # NOTE: When this prompt is in use the gdb_test procedure cannot be used because |
| # it assumes that the last char after the gdb_prompt is a white space. This is not |
| # true with this annotated prompt. So we must use send_gdb and gdb_expect. |
| # |
| |
| set old_gdb_prompt $gdb_prompt |
| set gdb_prompt "\r\n\032\032pre-prompt\r\n$gdb_prompt \r\n\032\032prompt\r\n" |
| |
| # |
| # Escape all the characters in the path that need it. For instance |
| # the directory name could contain '+'. |
| # |
| set escapedsrcfile [string_to_regexp ${srcdir}/${subdir}/${srcfile}] |
| |
| |
| # |
| # set the annotation level to 2 |
| # |
| # of course, this will test: |
| # annotate-pre-prompt |
| # annotate-prompt |
| # annotate-post-prompt (in the next block) |
| # |
| send_gdb "set annotate 2\n" |
| gdb_expect { |
| -re "set annotate 2\r\n$gdb_prompt$" { pass "annotation set at level 2" } |
| -re ".*$gdb_prompt$" { fail "annotation set at level 2" } |
| timeout { fail "annotation set at level 2 (timeout)" } |
| } |
| |
| |
| # |
| # info break will test: |
| # annotate-breakpoints-headers |
| # annotate-field |
| # annotate-breakpoints-table |
| # annotate-record |
| # annotate-breakpoints-table-end |
| # |
| gdb_test_multiple "info break" "breakpoint info" { |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032breakpoints-headers\r\n\r\n\032\032field 0\r\nNum \r\n\032\032field 1\r\nType \r\n\032\032field 2\r\nDisp \r\n\032\032field 3\r\nEnb \r\n\032\032field 4\r\nAddress +\r\n\032\032field 5\r\nWhat\r\n\r\n\032\032breakpoints-table\r\n\r\n\032\032record\r\n\r\n\032\032field 0\r\n1 \r\n\032\032field 1\r\nbreakpoint \r\n\032\032field 2\r\nkeep \r\n\032\032field 3\r\ny \r\n\032\032field 4\r\n$hex +\r\n\032\032field 5\r\nin main at ${escapedsrcfile}:$main_line\r\n\r\n\032\032breakpoints-table-end\r\n$gdb_prompt$" { |
| pass "breakpoint info" |
| } |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032breakpoints-headers\r\n\r\n\032\032field 0\r\nNum \r\n\032\032field 1\r\nType \r\n\032\032field 2\r\nDisp \r\n\032\032field 3\r\nEnb \r\n\032\032field 4\r\nAddress +\r\n\032\032field 5\r\nWhat\r\n\r\n\032\032breakpoints-table\r\n\r\n\032\032record\r\n\r\n\032\032field 0\r\n1 \r\n\032\032field 1\r\nbreakpoint \r\n\032\032field 2\r\nkeep \r\n\032\032field 3\r\ny \r\n\032\032field 4\r\n$hex +\r\n\032\032field 5\r\nin main at .*${srcfile}:$main_line\r\n\r\n\032\032breakpoints-table-end\r\n$gdb_prompt$" { |
| setup_xfail "*-*-*" 1270 |
| fail "breakpoint info" |
| } |
| } |
| |
| |
| # |
| # run to a break point will test: |
| # annotate-frames-invalid |
| # annotate-breakpoints-invalid (a.k.a. breakpoints-changed) |
| # annotate-starting |
| # annotate-breakpoint |
| # annotate-frame-begin |
| # annotate-frame-function-name |
| # annotate-frame-args |
| # annotate-frame-source-begin |
| # annotate-frame-source-file |
| # annotate-frame-source-file-end |
| # annotate-frame-source-line |
| # annotate-frame-source-end |
| # annotate-source |
| # annotate-frame-end |
| # annotate-stopped |
| # |
| #exp_internal 1 |
| set binexp [string_to_regexp $binfile] |
| gdb_test_multiple "run" "run until main breakpoint" { |
| -re "\r\n\032\032post-prompt\r\nStarting program: $binexp \(\r\nwarning: Skipping \[^\r\n\]+ .gdb_index section in \[^\r\n\]+\r\nDo \"set use-deprecated-index-sections on\" before the file is read\r\nto use the section anyway\\.\)?\(\(\r\n\r\n\032\032frames-invalid\)|\(\r\n\r\n\032\032breakpoints-invalid\)\)*\r\n\r\n\032\032starting\(\(\r\n\r\n\032\032frames-invalid\)|\(\r\n\r\n\032\032breakpoints-invalid\)\)*\r\n\r\n\032\032breakpoint 1\r\n\r\nBreakpoint 1, \r\n\032\032frame-begin 0 $hex\r\n\r\n\032\032frame-function-name\r\nmain\r\n\032\032frame-args\r\n \\(\\)\r\n\032\032frame-source-begin\r\n at \r\n\032\032frame-source-file\r\n.*annota1.c\r\n\032\032frame-source-file-end\r\n:\r\n\032\032frame-source-line\r\n$main_line\r\n\032\032frame-source-end\r\n\r\n\r\n\032\032source.*$srcfile:$main_line:.*:beg:$hex\r\n\r\n\032\032frame-end\r\n\r\n\032\032stopped.*$gdb_prompt$" { |
| pass "run until main breakpoint" |
| } |
| } |
| #exp_internal 0 |
| #exit 0 |
| |
| # |
| # Let's do a next, to get to a point where the array is initialized |
| # We don't care about the annotated output for this operation, it is the same as |
| # the one produced by run above |
| # |
| gdb_test_multiple "next" "go after array init line" { |
| -re "source .*annota1.c.*$gdb_prompt$" { |
| pass "go after array init line" |
| } |
| } |
| |
| |
| # |
| # printing the array will test: |
| # annotate-value-history-begin |
| # annotate-value-history-value |
| # annotate-array-section-begin |
| # annotate-elt |
| # FIXME: annotate-elt-rep and annotate-elt-rep-end not tested |
| # annotate-array-section-end |
| # annotate-value-history-end |
| # FIXME: annotate-value-begin and annotate-value-end not tested (the gdb output |
| # command would cause them to be used) |
| # |
| gdb_test_multiple "print my_array" "print array" { |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032value-history-begin 1 -\r\n.*= \r\n\032\032value-history-value\r\n.\r\n\032\032array-section-begin 0 -\r\n1\r\n\032\032elt\r\n, 2\r\n\032\032elt\r\n, 3\r\n\032\032elt\r\n\r\n\032\032array-section-end\r\n.\r\n\r\n\032\032value-history-end\r\n$gdb_prompt$" { |
| pass "print array" |
| } |
| } |
| |
| |
| # |
| # this should generate an error message, so to test: |
| # annotate-error-begin |
| # FIXME: annotate-error not tested |
| # |
| |
| #exp_internal 1 |
| gdb_test_multiple "print non_existent_value" "print non_existent_value" { |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032error-begin\r\nNo symbol \"non_existent_value\" in current context.\r\n\r\n\032\032error\r\n$gdb_prompt$" { |
| pass "print non_existent_value" |
| } |
| } |
| |
| |
| # |
| # break at signal handler. So that, once we are in the sig handler, if we do a bt |
| # we can test annotate-signal-handler-caller |
| # |
| gdb_test_multiple "break handle_USR1" "break handle_USR1" { |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032breakpoints-invalid\r\nBreakpoint.*at $hex: file.*$srcfile, line.*\r\n$gdb_prompt$" { |
| pass "break handle_USR1" |
| } |
| } |
| |
| # |
| # break at printf. When we are stopped at printf, we can test |
| # |
| gdb_test_multiple "break printf" "break printf" { |
| -re "\r\n\032\032post-prompt\r\n\r\n\032\032breakpoints-invalid\r\nBreakpoint.*at $hex.*$gdb_prompt$" { |
| pass "break printf" |
| } |
| -re "\r\n\032\032post-prompt\r\nwarning: Breakpoint address adjusted from $hex to $hex.\r\n\r\n\032\032breakpoints-invalid\r\nBreakpoint.*at $hex.*$gdb_prompt$" { |
| pass "break printf" |
| } |
| } |
| |
| # |
| # get to printf |
| # |
| set pat_begin "\r\n\032\032post-prompt\r\nContinuing.\r\n\r\n\032\032starting\(\r\n\r\n\032\032frames-invalid\)+\r\n" |
| set pat_adjust "warning: Breakpoint 3 address previously adjusted from $hex to $hex.\r\n" |
| set pat_end "\r\n\032\032breakpoint 3\r\n\r\nBreakpoint 3, \r\n\032\032frame-begin 0 $hex\r\n\r\n(\032\032frame-address\r\n$hex\r\n\032\032frame-address-end\r\n in \r\n)*.*\032\032frame-function-name\r\n.*printf(@.*)?\r\n\032\032frame-args\r\n.*\032\032frame-end\r\n\r\n\032\032stopped\r\n$gdb_prompt$" |
| |
| gdb_test_multiple "continue" "continue to printf" { |
| -re "${pat_begin}($pat_adjust)?$pat_end" { |
| pass "continue to printf" |
| } |
| -re ".*$gdb_prompt$" { fail "continue to printf" } |
| } |
| |
| # |
| # test: |
| # annotate-frame-where |
| # annotate-frame-address |
| # annotate-frame-address-end |
| # |
| set pat_begin "\r\n\032\032post-prompt\r\n\r\n\032\032frame-begin 0 $hex\r\n.0 \r\n(\032\032frame-address\r\n$hex\r\n\032\032frame-address-end\r\n in \r\n)*\032\032frame-function-name\r\n.*printf(@.*)?\r\n\032\032frame-args\r\n \\(.*frame-end\r\n\r\n\032\032frame-begin 1 $hex\r\n.1 \r\n\032\032frame-address\r\n$hex\r\n\032\032frame-address-end\r\n in \r\n\032\032frame-function-name\r\nmain\r\n\032\032frame-args\r\n \\(\\)\r\n\032\032frame-source-begin\r\n at \r\n\032\032frame-source-file\r\n" |
| |
| set pat_end "\r\n\032\032frame-source-file-end\r\n:\r\n\032\032frame-source-line\r\n.*\r\n\032\032frame-source-end\r\n\r\n\r\n\032\032frame-end\r\n(\r\n\032\032frame-begin .*\r\n\r\n\032\032frame-end\r\n)*$gdb_prompt$" |
| |
| gdb_test_multiple "backtrace" "backtrace from shlibrary" { |
| -re "$pat_begin$escapedsrcfile$pat_end" { |
| pass "backtrace from shlibrary" |
| } |
| -re "$pat_begin.*$srcfile$pat_end" { |
| setup_xfail "*-*-*" 1270 |
| fail "backtrace from shlibrary" |
| } |
| } |
| |
| |
| # |
| # test printing a frame with some arguments: |
| # annotate-arg-begin |
| # annotate-arg-name-end |
| # annotate-arg-value |
| # annotate-arg-end |
| # |
| |
| if [target_info exists gdb,nosignals] { |
| unsupported "send SIGUSR1" |
| unsupported "backtrace @ signal handler" |
| } else { |
| gdb_test_multiple "signal SIGUSR1" "send SIGUSR1" { |
| -re "\r\n\032\032post-prompt\r\nContinuing with signal SIGUSR1.\r\n\r\n\032\032starting\(\(\r\n\r\n\032\032frames-invalid\)|\(\r\n\r\n\032\032breakpoints-invalid\)\)+\r\n\r\n\032\032breakpoint 2\r\n\r\nBreakpoint 2, \r\n\032\032frame-begin 0 $hex\r\n\r\n\032\032frame-function-name\r\nhandle_USR1\r\n\032\032frame-args\r\n \\(\r\n\032\032arg-begin\r\nsig\r\n\032\032arg-name-end\r\n=\r\n\032\032arg-value -\r\n$decimal\r\n\032\032arg-end\r\n\\)\r\n\032\032frame-source-begin\r\n at \r\n\032\032frame-source-file\r\n${escapedsrcfile}\r\n\032\032frame-source-file-end\r\n:\r\n\032\032frame-source-line\r\n.*\r\n\032\032frame-source-end\r\n\r\n\r\n\032\032source.*annota1.c:.*:.*:beg:$hex\r\n\r\n\032\032frame-end\r\n\r\n\032\032stopped\r\n$gdb_prompt$" { |
| pass "send SIGUSR1" |
| } |
| -re "\r\n\032\032post-prompt\r\nContinuing with signal SIGUSR1.\r\n\r\n\032\032starting\(\(\r\n\r\n\032\032frames-invalid\)|\(\r\n\r\n\032\032breakpoints-invalid\)\)+\r\n\r\n\032\032breakpoint 2\r\n\r\nBreakpoint 2, \r\n\032\032frame-begin 0 $hex\r\n\r\n\032\032frame-function-name\r\nhandle_USR1\r\n\032\032frame-args\r\n \\(\r\n\032\032arg-begin\r\nsig\r\n\032\032arg-name-end\r\n=\r\n\032\032arg-value -\r\n$decimal\r\n\032\032arg-end\r\n\\)\r\n\032\032frame-source-begin\r\n at \r\n\032\032frame-source-file\r\n.*${srcfile}\r\n\032\032frame-source-file-end\r\n:\r\n\032\032frame-source-line\r\n.*\r\n\032\032frame-source-end\r\n\r\n\r\n\032\032source.*annota1.c:.*:.*:beg:$hex\r\n\r\n\032\032frame-end\r\n\r\n\032\032stopped\r\n$gdb_prompt$" { |
| setup_xfail "*-*-*" 1270 |
| fail "send SIGUSR1" |
| } |
| } |
| |
| # |
| # test: |
| # annotate-signal-handler-caller |
| # |
| gdb_test_multiple "backtrace" "backtrace @ signal handler" { |
| -re "frame-begin 0 $hex\r\n#0.*frame-end.*frame-begin 1 $hex\r\n#1.*(\032\032signal-handler-caller\r\n.signal handler called.\r\n\r\n)+\032\032frame-end\r\n\r\n\032\032frame-begin 2 $hex\r\n#2.*(frame-begin 3 $hex\r\n#3.*)*frame-end.*$gdb_prompt$" { |
| pass "backtrace @ signal handler" |
| } |
| } |
| } |
| |
| # |
| # delete all the breakpoints |
| # |
| gdb_test_multiple "delete 1" "delete bp 1" { |
| -re "\r\n\032\032post-prompt\r\n$gdb_prompt$" { |
| pass "delete bp 1" |
| } |
| } |
| |
| gdb_test_multiple "delete 2" "delete bp 2" { |
| -re "\r\n\032\032post-prompt\r\n$gdb_prompt$" { |
| pass "delete bp 2" |
| } |
| } |
| |
| gdb_test_multiple "delete 3" "delete bp 3" { |
| -re "\r\n\032\032post-prompt\r\n$gdb_prompt$" { |
| pass "delete bp 3" |
| } |
| } |
| |
| # |
| # break at main, after value is initialized. This is in preparation |
| # to test the annotate output for the display command. |
| # |
| gdb_test_multiple "break main" "break at main" { |
| -re "post-prompt.*\032\032breakpoints-invalid.*Breakpoint 4 at $hex: file ${escapedsrcfile}, line $main_line.*$gdb_prompt$" { |
| pass "break at main" |
| } |
| -re "post-prompt.*\032\032breakpoints-invalid.*Breakpoint 4 at $hex: file .*${srcfile}, line $main_line.*$gdb_prompt$" { |
| setup_xfail "*-*-*" 1270 |
| fail "break at main" |
| } |
| } |
| |
| # |
| # display the value; test: |
| # annotate-display-begin |
| # annotate-display-number-end |
| # annotate-display-format |
| # annotate-display-expression |
| # annotate-display-expression-end |
| # annotate-display-end |
| # FIXME: annotate-display-value not tested |
| # |
| gdb_test_multiple "display value" "set up display" { |
| -re "post-prompt\r\n\r\n\032\032display-begin\r\n1\r\n\032\032display-number-end\r\n: \r\n\032\032display-format\r\n\r\n\032\032display-expression\r\nvalue\r\n\032\032display-expression-end\r\n = \r\n\032\032display-expression\r\n7\r\n\r\n\032\032display-end\r\n$gdb_prompt$" { |
| pass "set up display" |
| } |
| } |
| |
| |
| # should ask query. Test annotate-query. |
| # we don't care about anything else here, only the query. |
| |
| send_gdb "run\n" |
| gdb_expect { |
| -re "pre-query.*already.*\\(y or n\\).*query\r\n" { |
| send_gdb "y\n" |
| gdb_expect { |
| -re ".*post-query.*$gdb_prompt$" \ |
| { pass "re-run" } |
| -re ".*$gdb_prompt$" { fail "re-run" } |
| timeout { fail "re-run (timeout)" } |
| } |
| } |
| -re ".*$gdb_prompt$" { fail "re-run" } |
| timeout { fail "re-run (timeout)" } |
| } |
| |
| # |
| # Test that breakpoints-invalid is issued once and only once for |
| # breakpoint ignore count changes, after annotation stopped. |
| # |
| |
| set value_inc_line [gdb_get_line_number "increment value"] |
| |
| gdb_test_multiple "break $value_inc_line" "break at value++" { |
| -re "Breakpoint 5 at $hex: file .*$srcfile, line $value_inc_line.*$gdb_prompt$" { |
| pass "break at value++" |
| } |
| } |
| |
| gdb_test_multiple "ignore 5 4" "ignore 5 4" { |
| -re "Will ignore next 4 crossings of breakpoint 5.*$gdb_prompt$" { |
| pass "ignore 5 4" |
| } |
| } |
| |
| gdb_test_multiple "continue" "annotate ignore count change" { |
| -re ".*$srcfile:$value_inc_line:.*\032\032stopped\r\n\r\n\032\032breakpoints-invalid\r\n$gdb_prompt$" { |
| pass "annotate ignore count change" |
| } |
| } |
| |
| # check that ignore command is working, or the above can provide |
| # misleading assurance ... |
| |
| gdb_test_multiple "next" "next to exit loop" { |
| -re "source .*annota1.c.*$gdb_prompt$" { |
| } |
| } |
| |
| set after_loop_line [gdb_get_line_number "after loop"] |
| |
| gdb_test_multiple "next" "breakpoint ignore count" { |
| -re ".*$srcfile:$after_loop_line:.*$gdb_prompt$" { |
| pass "breakpoint ignore count" |
| } |
| } |
| |
| # Get the inferior's PID for later. |
| |
| set test "get inferior pid" |
| set pid -1 |
| gdb_test_multiple "info inferior 1" "$test" { |
| -re "process (\[0-9\]*).*$gdb_prompt$" { |
| set pid $expect_out(1,string) |
| pass "$test" |
| } |
| } |
| |
| # |
| # Send a signal that is not handled; test: |
| # annotate-signalled |
| # annotate-signal-name |
| # annotate-signal-name-end |
| # annotate-signal-string |
| # annotate-signal-string-end |
| # FIXME: annotate-signal not tested (requires that the inferior be |
| # stopped by a "random" signal) |
| # |
| # SIGTRAP signals are dropped before they get to the inferior process |
| # on hpux11. In theory, this behaivor can be controlled by setting |
| # TTEO_NORM_SIGTRAP in the inferior, but doing so did not cause |
| # the signal to be properly delivered. |
| # |
| # It has been verified that other signals will be delivered. However, |
| # rather than twiddle the test, I choose to leave it as-is as it |
| # exposes an interesting failure on hpux11. |
| |
| if [target_info exists gdb,nosignals] { |
| unsupported "signal sent" |
| } else { |
| setup_xfail hppa*-*-hpux11* |
| gdb_test_multiple "signal SIGTRAP" "signal sent" { |
| -re ".*\032\032post-prompt\r\nContinuing with signal SIGTRAP.\r\n\r\n\032\032starting\(\r\n\r\n\032\032frames-invalid\)+\r\n\r\n\032\032signalled\r\n\r\nProgram terminated with signal \r\n\032\032signal-name\r\nSIGTRAP\r\n\032\032signal-name-end\r\n, \r\n\032\032signal-string\r\nTrace.breakpoint trap\r\n\032\032signal-string-end\r\n.\r\nThe program no longer exists.\r\n\r\n\032\032stopped\r\n$gdb_prompt$" { |
| pass "signal sent" |
| } |
| } |
| } |
| |
| # Check for production of a core file and remove it! |
| |
| set test "cleanup core file" |
| if { [remote_file host exists core] } { |
| remote_file host delete core |
| pass "$test (removed)" |
| } elseif { $pid != -1 && [remote_file host exists core.$pid] } { |
| remote_file host delete core.$pid |
| pass "$test (removed)" |
| } else { |
| pass "$test (not dumped)" |
| } |
| |
| proc thread_test {} { |
| global objdir subdir srcdir testfile |
| global gdb_prompt old_gdb_prompt |
| set srcfile watch_thread_num.c |
| set binfile ${objdir}/${subdir}/${testfile}-watch_thread_num |
| set gdb_prompt $old_gdb_prompt |
| |
| if { ![get_compiler_info] && [gdb_compile_pthreads "${srcdir}/${subdir}/${srcfile}" "${binfile}" executable {debug nowarnings}] == "" } { |
| |
| gdb_exit |
| gdb_start |
| gdb_reinitialize_dir $srcdir/$subdir |
| gdb_load ${binfile} |
| if { ![runto main] } then { |
| fail "run to main" |
| return |
| } |
| |
| set gdb_prompt \ |
| "\r\n\032\032pre-prompt\r\n$gdb_prompt \r\n\032\032prompt\r\n" |
| |
| gdb_test_multiple "set annotate 2" "" { |
| -re "set annotate 2\r\n$gdb_prompt$" { |
| } |
| } |
| |
| gdb_test_multiple "next 2" "new thread" { |
| -re ".*\032\032new-thread" { |
| pass "new thread" |
| } |
| } |
| } |
| } |
| |
| proc thread_switch {} { |
| gdb_test_multiple "thread 1" "thread switch" { |
| -re ".*\032\032thread-changed" { |
| pass "thread switch" |
| } |
| } |
| } |
| |
| thread_test |
| thread_switch |
| |
| # restore the original prompt for the rest of the testsuite |
| |
| set gdb_prompt $old_gdb_prompt |
