blob: 590ff62531c2d53cbc8bca00204e16af90ae5029 [file] [log] [blame]
ARM Trusted Firmware for Socionext UniPhier SoCs
================================================
Socionext UniPhier ARMv8-A SoCs use ARM Trusted Firmware as the secure world
firmware, supporting BL2 and BL31.
UniPhier SoC family implements its internal boot ROM, which loads 64KB [1]_
image from a non-volatile storage to the on-chip SRAM, and jumps over to it.
ARM Trusted Firmware provides a special mode, BL2-AT-EL3, which enables BL2 to
execute at EL3. It is useful for platforms with non-TF boot ROM, like UniPhier.
Here, a problem is BL2 does not fit in the 64KB limit if `Trusted Board Boot`_
(TBB) is enabled. To solve this issue, Socionext provides a first stage loader
called `UniPhier BL`_. This loader runs in the on-chip SRAM, initializes the
DRAM, expands BL2 there, and hands the control over to it. Therefore, all images
of ARM Trusted Firmware run in DRAM.
The UniPhier platform works with/without TBB. See below for the build process
of each case. The image authentication for the UniPhier platform fully
complies with the Trusted Board Boot Requirements (TBBR) specification.
The UniPhier BL does not implement the authentication functionality, that is,
it can not verify the BL2 image by itself. Instead, the UniPhier BL assures
the BL2 validity in a different way; BL2 is GZIP-compressed and appended to
the UniPhier BL. The concatenation of the UniPhier BL and the compressed BL2
fits in the 64KB limit. The concatenated image is loaded by the internal boot
ROM (and verified if the chip fuses are blown).
Boot Flow
---------
1. The Boot ROM
This is hard-wired ROM, so never corrupted. It loads the UniPhier BL (with
compressed-BL2 appended) into the on-chip SRAM. If the SoC fuses are blown,
the image is verified by the SoC's own method.
2. UniPhier BL
This runs in the on-chip SRAM. After the minimum SoC initialization and DRAM
setup, it decompresses the appended BL2 image into the DRAM, then jumps to
the BL2 entry.
3. BL2 (at EL3)
This runs in the DRAM. It extracts more images such as BL31, BL33 (optionally
SCP_BL2, BL32 as well) from Firmware Image Package (FIP). If TBB is enabled,
they are all authenticated by the standard mechanism of ARM Trusted Firmware.
After loading all the images, it jumps to the BL31 entry.
4. BL31, BL32, and BL33
They all run in the DRAM. See `Firmware Design`_ for details.
Basic Build
-----------
BL2 must be compressed for the reason above. The UniPhier's platform makefile
provides a build target ``bl2_gzip`` for this.
For a non-secure boot loader (aka BL33), U-Boot is well supported for UniPhier
SoCs. The U-Boot image (``u-boot.bin``) must be built in advance. For the build
procedure of U-Boot, refer to the document in the `U-Boot`_ project.
To build minimum functionality for UniPhier (without TBB)::
make CROSS_COMPILE=<gcc-prefix> PLAT=uniphier BL33=<path-to-BL33> bl2_gzip fip
Output images:
- ``bl2.bin.gz``
- ``fip.bin``
Optional features
-----------------
- Trusted Board Boot
`mbed TLS`_ is needed as the cryptographic and image parser modules.
Refer to the `User Guide`_ for the appropriate version of mbed TLS.
To enable TBB, add the following options to the build command::
TRUSTED_BOARD_BOOT=1 GENERATE_COT=1 MBEDTLS_DIR=<path-to-mbedtls>
- System Control Processor (SCP)
If desired, FIP can include an SCP BL2 image. If BL2 finds an SCP BL2 image
in FIP, BL2 loads it into DRAM and kicks the SCP. Most of UniPhier boards
still work without SCP, but SCP provides better power management support.
To include SCP BL2, add the following option to the build command::
SCP_BL2=<path-to-SCP>
- BL32 (Secure Payload)
To enable BL32, add the following options to the build command::
SPD=<spd> BL32=<path-to-BL32>
If you use TSP for BL32, ``BL32=<path-to-BL32>`` is not required. Just add the
following::
SPD=tspd
.. [1] Some SoCs can load 80KB, but the software implementation must be aligned
to the lowest common denominator.
.. _Trusted Board Boot: ../trusted-board-boot.rst
.. _UniPhier BL: https://github.com/uniphier/uniphier-bl
.. _Firmware Design: ../firmware-design.rst
.. _U-Boot: https://www.denx.de/wiki/U-Boot
.. _mbed TLS: https://tls.mbed.org/
.. _User Guide: ../user-guide.rst