blob: 9ce04342349703f316fa0e90f72184278f1dbb13 [file] [log] [blame]
/*
* Copyright (c) 2017, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#ifndef __POPLAR_LAYOUT_H
#define __POPLAR_LAYOUT_H
/*
* Boot memory layout definitions for the HiSilicon Poplar board
*/
/*
* When Poplar is powered on, boot ROM verifies the initial content of
* boot media, loads it into low memory, and begins executing it
* in 32-bit mode. The image loaded is "l-loader.bin", which contains
* a small amount code along with an embedded ARM Trusted Firmware
* BL1 image. The main purpose of "l-loader" is to prepare the
* processor to execute the BL1 image in 64-bit mode, and to trigger
* that execution.
*
* Also embedded in "l-loader.bin" is a FIP image that contains
* other ARM Trusted Firmware images: BL2; BL31; and for BL33,
* U-Boot. When BL1 executes, it unpacks the BL2 image from the FIP
* image into a region of memory set aside to hold it. Similarly,
* BL2 unpacks BL31 into memory reserved for it, and unpacks U-Boot
* into high memory.
*
* Because the BL1 code is embedded in "l-loader", its base address
* in memory is derived from the base address of the "l-loader"
* text section, together with an offset. Memory space for BL2 is
* reserved immediately following BL1, and memory space is reserved
* for BL31 after that. ARM Trusted Firmware requires each of these
* memory regions to be aligned on page boundaries, so the size of
* each region is a multiple of a page size (ending in 000). Note
* that ARM Trusted Firmware requires the read-only and read-write
* regions of memory used for BL1 to be defined separately.
*
* ---------------------
* | (unused memory) |
* +-------------------+ - - - - -
* | (l-loader text) | \
* +-------------------+ \
* | BL1 (read-only) | \ \
* |- - - - - - - - - -| | |
* | BL1 (read-write) | | |
* +-------------------+ > BL Memory |
* | Reserved for BL2 | | > "l-loader.bin" image
* +-------------------+ | |
* | Reserved for BL31 | / |
* +-------------------+ |
* . . . /
* +-------------------+ /
* | FIP | /
* +-------------------+ - - - - -
* . . .
* | (unused memory) |
* . . .
* +-------------------+
* |Reserved for U-Boot|
* +-------------------+
* . . .
* | (unused memory) |
* ---------------------
*
* The size of each of these regions is defined below. The base
* address of the "l-loader" TEXT section and the offset of the BL1
* image within that serve as anchors for defining the positions of
* all other regions. The FIP is placed in a section of its own.
*
* A "BASE" is the memory address of the start of a region; a "LIMIT"
* marks its end. A "SIZE" is the size of a region (in bytes). An
* "OFFSET" is an offset to the start of a region relative to the
* base of the "l-loader" TEXT section (also a multiple of page size).
*/
#define LLOADER_TEXT_BASE 0x02001000 /* page aligned */
#define BL1_OFFSET 0x0000D000 /* page multiple */
#define FIP_BASE 0x02040000
/*
* FIP_BASE_EMMC = 0x40000 - 0x1000
* = fip.bin offset - l-loader text offset
* in l-loader.bin
*/
#define FIP_BASE_EMMC 0x0003f000
#define BL1_RO_SIZE 0x00008000 /* page multiple */
#define BL1_RW_SIZE 0x00008000 /* page multiple */
#define BL1_SIZE (BL1_RO_SIZE + BL1_RW_SIZE)
#define BL2_SIZE 0x0000c000 /* page multiple */
#define BL31_SIZE 0x00014000
#if !POPLAR_RECOVERY
/*
* emmc partition1 4096KB
* - l-loader.bin 1984KB
* |- l-loader + bl1.bin 256KB
* |- fip.bin 1728KB (0x001b0000)
* - u-boot persistent data 64KB
* - uefi persistent data 2048KB
*/
#define FIP_SIZE 0x001b0000 /* absolute max */
#else
/*
* same as above, but bootrom can only load an image (l-loader.bin) of
* 1024KB max, so after deducting the size of l-loader + bl1.bin (256KB),
* that leaves 768KB (0x000c0000) for fip.bin
*/
#define FIP_SIZE 0x000c0000 /* absolute max */
#endif
/* BL1_OFFSET */ /* (Defined above) */
#define BL1_BASE (LLOADER_TEXT_BASE + BL1_OFFSET)
#define BL1_LIMIT (BL1_BASE + BL1_SIZE)
#define BL1_RO_OFFSET (BL1_OFFSET)
#define BL1_RO_BASE (LLOADER_TEXT_BASE + BL1_RO_OFFSET)
#define BL1_RO_LIMIT (BL1_RO_BASE + BL1_RO_SIZE)
#define BL1_RW_OFFSET (BL1_RO_OFFSET + BL1_RO_SIZE)
#define BL1_RW_BASE (LLOADER_TEXT_BASE + BL1_RW_OFFSET)
#define BL1_RW_LIMIT (BL1_RW_BASE + BL1_RW_SIZE)
#define BL2_OFFSET (BL1_OFFSET + BL1_SIZE)
#define BL2_BASE (LLOADER_TEXT_BASE + BL2_OFFSET)
#define BL2_LIMIT (BL2_BASE + BL2_SIZE)
#define BL31_OFFSET (BL2_OFFSET + BL2_SIZE)
#define BL31_BASE (LLOADER_TEXT_BASE + BL31_OFFSET)
#define BL31_LIMIT (BL31_BASE + BL31_SIZE)
#endif /* !__POPLAR_LAYOUT_H */