Merge "fix(sdei): set SPSR for SDEI based on TakeException" into integration
diff --git a/docs/about/maintainers.rst b/docs/about/maintainers.rst
index 97e1fa8..725e96b 100644
--- a/docs/about/maintainers.rst
+++ b/docs/about/maintainers.rst
@@ -399,6 +399,7 @@
:|G|: `vishnu-banavath`_
:|F|: plat/arm/board/corstone700
:|F|: plat/arm/board/a5ds
+:|F|: plat/arm/board/diphda
Arm Reference Design platform ports
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
@@ -493,8 +494,8 @@
NXP i.MX 8 platform port
^^^^^^^^^^^^^^^^^^^^^^^^
-:|M|: Anson Huang <Anson.Huang@nxp.com>
-:|G|: `Anson-Huang`_
+:|M|: Peng Fan <peng.fan@nxp.com>
+:|G|: `MrVan`_
:|F|: docs/plat/imx8.rst
:|F|: plat/imx/
diff --git a/docs/design/cpu-specific-build-macros.rst b/docs/design/cpu-specific-build-macros.rst
index ab638fb..949845a 100644
--- a/docs/design/cpu-specific-build-macros.rst
+++ b/docs/design/cpu-specific-build-macros.rst
@@ -323,6 +323,16 @@
CPU. This needs to be enabled for revisions r3p0, r3p1, r4p0, and r4p1, for
revisions r0p0, r1p0, and r2p0 there is no workaround.
+For Neoverse V1, the following errata build flags are defined :
+
+- ``ERRATA_V1_1791573``: This applies errata 1791573 workaround to Neoverse-V1
+ CPU. This needs to be enabled only for revisions r0p0 and r1p0, it is fixed
+ in r1p1.
+
+- ``ERRATA_V1_1940577``: This applies errata 1940577 workaround to Neoverse-V1
+ CPU. This needs to be enabled only for revision r1p0 and r1p1 of the
+ CPU.
+
DSU Errata Workarounds
----------------------
diff --git a/docs/plat/arm/diphda/index.rst b/docs/plat/arm/diphda/index.rst
new file mode 100644
index 0000000..27afda4
--- /dev/null
+++ b/docs/plat/arm/diphda/index.rst
@@ -0,0 +1,61 @@
+Diphda Platform
+==========================
+
+Some of the features of the Diphda platform referenced in TF-A include:
+
+- Cortex-A35 application processor (64-bit mode)
+- Secure Enclave
+- GIC-400
+- Trusted Board Boot
+
+Boot Sequence
+-------------
+
+The board boot relies on CoT (chain of trust). The trusted-firmware-a
+BL2 is extracted from the FIP and verified by the Secure Enclave
+processor. BL2 verification relies on the signature area at the
+beginning of the BL2 image. This area is needed by the SecureEnclave
+bootloader.
+
+Then, the application processor is released from reset and starts by
+executing BL2.
+
+BL2 performs the actions described in the trusted-firmware-a TBB design
+document.
+
+Build Procedure (TF-A only)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+- Obtain AArch64 ELF bare-metal target `toolchain <https://developer.arm.com/tools-and-software/open-source-software/developer-tools/gnu-toolchain/gnu-a/downloads>`_.
+ Set the CROSS_COMPILE environment variable to point to the toolchain folder.
+
+- Build TF-A:
+
+ .. code:: shell
+
+ make LD=aarch64-none-elf-ld \
+ CC=aarch64-none-elf-gcc \
+ V=1 \
+ BUILD_BASE=<path to the build folder> \
+ PLAT=diphda \
+ SPD=spmd \
+ SPMD_SPM_AT_SEL2=0 \
+ DEBUG=1 \
+ MBEDTLS_DIR=mbedtls \
+ OPENSSL_DIR=<path to openssl usr folder> \
+ RUNTIME_SYSROOT=<path to the sysroot> \
+ ARCH=aarch64 \
+ TARGET_PLATFORM=<fpga or fvp> \
+ ENABLE_PIE=1 \
+ BL2_AT_EL3=1 \
+ CREATE_KEYS=1 \
+ GENERATE_COT=1 \
+ TRUSTED_BOARD_BOOT=1 \
+ COT=tbbr \
+ ARM_ROTPK_LOCATION=devel_rsa \
+ ROT_KEY=plat/arm/board/common/rotpk/arm_rotprivk_rsa.pem \
+ BL32=<path to optee binary> \
+ BL33=<path to u-boot binary> \
+ bl2
+
+*Copyright (c) 2021, Arm Limited. All rights reserved.*
diff --git a/docs/plat/arm/index.rst b/docs/plat/arm/index.rst
index f72992b..f50dab5 100644
--- a/docs/plat/arm/index.rst
+++ b/docs/plat/arm/index.rst
@@ -12,6 +12,7 @@
arm_fpga/index
arm-build-options
morello/index
+ diphda/index
This chapter holds documentation related to Arm's development platforms,
including both software models (FVPs) and hardware development boards
@@ -19,4 +20,4 @@
--------------
-*Copyright (c) 2019, Arm Limited. All rights reserved.*
+*Copyright (c) 2021, Arm Limited. All rights reserved.*
diff --git a/docs/plat/deprecated.rst b/docs/plat/deprecated.rst
index 203ae00..7cc4258 100644
--- a/docs/plat/deprecated.rst
+++ b/docs/plat/deprecated.rst
@@ -16,3 +16,5 @@
+================+================+====================+====================+
| sgm775 | Arm | 2.5 | 2.7 |
+----------------+----------------+--------------------+--------------------+
+| mt6795 | MTK | 2.5 | 2.7 |
++----------------+----------------+--------------------+--------------------+
diff --git a/docs/plat/marvell/armada/build.rst b/docs/plat/marvell/armada/build.rst
index c9f5e82..09b4fa4 100644
--- a/docs/plat/marvell/armada/build.rst
+++ b/docs/plat/marvell/armada/build.rst
@@ -129,19 +129,16 @@
- MV_DDR_PATH
- For A7K/8K/CN913x, use this parameter to point to mv_ddr driver sources to allow BLE build. For A37x0,
- it is used for ddr_tool build.
+ This parameter is required for ``mrvl_flash`` and ``mrvl_uart`` targets.
+ For A7K/8K/CN913x it is used for BLE build and for Armada37x0 it used
+ for ddr_tool build.
- Usage example: MV_DDR_PATH=path/to/mv_ddr
+ Specify path to the full checkout of Marvell mv-ddr-marvell git
+ repository. Checkout must contain also .git subdirectory because
+ mv-ddr build process calls git commands.
- The parameter is optional for A7K/8K/CN913x, when this parameter is not set, the mv_ddr
- sources are expected to be located at: drivers/marvell/mv_ddr. However, the parameter
- is necessary for A37x0.
-
- For the mv_ddr source location, check the section "Tools and external components installation"
-
- If MV_DDR_PATH source code is a git snapshot then provide path to the full git
- repository (including .git subdir) because mv_ddr build process calls git commands.
+ Do not remove any parts of git checkout becuase build process and other
+ applications need them for correct building and version determination.
- CP_NUM
@@ -236,12 +233,17 @@
- WTP
- For Armada37x0 only, use this parameter to point to wtptools source code
- directory, which can be found as a3700_utils.zip in the release. Usage
- example: ``WTP=/path/to/a3700_utils``
+ For Armada37x0 only.
- If WTP source code is a git snapshot then provide path to the full git
- repository (including .git subdir) because WTP build process calls git commands.
+ Specify path to the full checkout of Marvell A3700-utils-marvell git
+ repository. Checkout must contain also .git subdirectory because WTP
+ build process calls git commands.
+
+ WTP build process uses also Marvell mv-ddr-marvell git repository
+ specified in MV_DDR_PATH option.
+
+ Do not remove any parts of git checkout becuase build process and other
+ applications need them for correct building and version determination.
- CRYPTOPP_PATH
diff --git a/drivers/scmi-msg/common.h b/drivers/scmi-msg/common.h
index ef5953b..62f3087 100644
--- a/drivers/scmi-msg/common.h
+++ b/drivers/scmi-msg/common.h
@@ -13,6 +13,7 @@
#include "base.h"
#include "clock.h"
+#include "power_domain.h"
#include "reset_domain.h"
#define SCMI_VERSION 0x20000U
@@ -111,6 +112,13 @@
scmi_msg_handler_t scmi_msg_get_rstd_handler(struct scmi_msg *msg);
/*
+ * scmi_msg_get_pd_handler - Return a handler for a power domain message
+ * @msg - message to process
+ * Return a function handler for the message or NULL
+ */
+scmi_msg_handler_t scmi_msg_get_pd_handler(struct scmi_msg *msg);
+
+/*
* Process Read, process and write response for input SCMI message
*
* @msg: SCMI message context
diff --git a/drivers/scmi-msg/entry.c b/drivers/scmi-msg/entry.c
index ea3efa2..3537fbe 100644
--- a/drivers/scmi-msg/entry.c
+++ b/drivers/scmi-msg/entry.c
@@ -11,6 +11,31 @@
#include "common.h"
+#pragma weak scmi_msg_get_clock_handler
+#pragma weak scmi_msg_get_rstd_handler
+#pragma weak scmi_msg_get_pd_handler
+#pragma weak scmi_msg_get_voltage_handler
+
+scmi_msg_handler_t scmi_msg_get_clock_handler(struct scmi_msg *msg __unused)
+{
+ return NULL;
+}
+
+scmi_msg_handler_t scmi_msg_get_rstd_handler(struct scmi_msg *msg __unused)
+{
+ return NULL;
+}
+
+scmi_msg_handler_t scmi_msg_get_pd_handler(struct scmi_msg *msg __unused)
+{
+ return NULL;
+}
+
+scmi_msg_handler_t scmi_msg_get_voltage_handler(struct scmi_msg *msg __unused)
+{
+ return NULL;
+}
+
void scmi_status_response(struct scmi_msg *msg, int32_t status)
{
assert(msg->out && msg->out_size >= sizeof(int32_t));
@@ -47,6 +72,9 @@
case SCMI_PROTOCOL_ID_RESET_DOMAIN:
handler = scmi_msg_get_rstd_handler(msg);
break;
+ case SCMI_PROTOCOL_ID_POWER_DOMAIN:
+ handler = scmi_msg_get_pd_handler(msg);
+ break;
default:
break;
}
diff --git a/drivers/scmi-msg/power_domain.c b/drivers/scmi-msg/power_domain.c
new file mode 100644
index 0000000..c4e1289
--- /dev/null
+++ b/drivers/scmi-msg/power_domain.c
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2015-2020, Arm Limited and Contributors. All rights reserved.
+ * Copyright (c) 2019-2020, Linaro Limited
+ */
+#include <cdefs.h>
+#include <string.h>
+
+#include <drivers/scmi-msg.h>
+#include <drivers/scmi.h>
+#include <lib/utils_def.h>
+
+#include "common.h"
+
+#pragma weak plat_scmi_pd_count
+#pragma weak plat_scmi_pd_get_name
+#pragma weak plat_scmi_pd_get_state
+#pragma weak plat_scmi_pd_set_state
+#pragma weak plat_scmi_pd_statistics
+#pragma weak plat_scmi_pd_get_attributes
+
+static bool message_id_is_supported(size_t message_id);
+
+size_t plat_scmi_pd_count(unsigned int agent_id __unused)
+{
+ return 0U;
+}
+
+const char *plat_scmi_pd_get_name(unsigned int agent_id __unused,
+ unsigned int pd_id __unused)
+{
+ return NULL;
+}
+
+unsigned int plat_scmi_pd_statistics(unsigned int agent_id __unused,
+ unsigned long *pd_id __unused)
+{
+ return 0U;
+}
+
+unsigned int plat_scmi_pd_get_attributes(unsigned int agent_id __unused,
+ unsigned int pd_id __unused)
+{
+ return 0U;
+}
+
+unsigned int plat_scmi_pd_get_state(unsigned int agent_id __unused,
+ unsigned int pd_id __unused)
+{
+ return 0U;
+}
+
+int32_t plat_scmi_pd_set_state(unsigned int agent_id __unused,
+ unsigned int flags __unused,
+ unsigned int pd_id __unused,
+ unsigned int state __unused)
+{
+ return SCMI_NOT_SUPPORTED;
+}
+
+static void report_version(struct scmi_msg *msg)
+{
+ struct scmi_protocol_version_p2a return_values = {
+ .status = SCMI_SUCCESS,
+ .version = SCMI_PROTOCOL_VERSION_PD,
+ };
+
+ if (msg->in_size != 0) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ scmi_write_response(msg, &return_values, sizeof(return_values));
+}
+
+static void report_attributes(struct scmi_msg *msg)
+{
+ unsigned long addr = 0UL;
+ unsigned int len;
+
+ struct scmi_protocol_attributes_p2a_pd return_values = {
+ .status = SCMI_SUCCESS,
+ };
+
+ if (msg->in_size != 0) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ return_values.attributes = plat_scmi_pd_count(msg->agent_id);
+ len = plat_scmi_pd_statistics(msg->agent_id, &addr);
+ if (len != 0U) {
+ return_values.statistics_addr_low = (unsigned int)addr;
+ return_values.statistics_addr_high = (uint32_t)(addr >> 32);
+ return_values.statistics_len = len;
+ }
+
+ scmi_write_response(msg, &return_values, sizeof(return_values));
+}
+
+static void report_message_attributes(struct scmi_msg *msg)
+{
+ struct scmi_protocol_message_attributes_a2p *in_args = (void *)msg->in;
+ struct scmi_protocol_message_attributes_p2a return_values = {
+ .status = SCMI_SUCCESS,
+ /* For this protocol, attributes shall be zero */
+ .attributes = 0U,
+ };
+
+ if (msg->in_size != sizeof(*in_args)) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ if (!message_id_is_supported(in_args->message_id)) {
+ scmi_status_response(msg, SCMI_NOT_FOUND);
+ return;
+ }
+
+ scmi_write_response(msg, &return_values, sizeof(return_values));
+}
+
+static void scmi_pd_attributes(struct scmi_msg *msg)
+{
+ const struct scmi_pd_attributes_a2p *in_args = (void *)msg->in;
+ struct scmi_pd_attributes_p2a return_values = {
+ .status = SCMI_SUCCESS,
+ };
+ const char *name = NULL;
+ unsigned int pd_id = 0U;
+
+ if (msg->in_size != sizeof(*in_args)) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ pd_id = SPECULATION_SAFE_VALUE(in_args->pd_id);
+
+ if (pd_id >= plat_scmi_pd_count(msg->agent_id)) {
+ scmi_status_response(msg, SCMI_INVALID_PARAMETERS);
+ return;
+ }
+
+ name = plat_scmi_pd_get_name(msg->agent_id, pd_id);
+ if (name == NULL) {
+ scmi_status_response(msg, SCMI_NOT_FOUND);
+ return;
+ }
+
+ COPY_NAME_IDENTIFIER(return_values.pd_name, name);
+
+ return_values.attributes = plat_scmi_pd_get_attributes(msg->agent_id, pd_id);
+
+ scmi_write_response(msg, &return_values, sizeof(return_values));
+}
+
+static void scmi_pd_state_get(struct scmi_msg *msg)
+{
+ const struct scmi_pd_state_get_a2p *in_args = (void *)msg->in;
+ unsigned int state = 0U;
+ struct scmi_pd_state_get_p2a return_values = {
+ .status = SCMI_SUCCESS,
+ };
+ unsigned int pd_id = 0U;
+
+ if (msg->in_size != sizeof(*in_args)) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ pd_id = SPECULATION_SAFE_VALUE(in_args->pd_id);
+
+ if (pd_id >= plat_scmi_pd_count(msg->agent_id)) {
+ scmi_status_response(msg, SCMI_INVALID_PARAMETERS);
+ return;
+ }
+
+ state = plat_scmi_pd_get_state(msg->agent_id, pd_id);
+
+ return_values.power_state = state;
+
+ scmi_write_response(msg, &return_values, sizeof(return_values));
+}
+
+static void scmi_pd_state_set(struct scmi_msg *msg)
+{
+ const struct scmi_pd_state_set_a2p *in_args = (void *)msg->in;
+ unsigned int flags = 0U;
+ int32_t status = 0;
+ unsigned int pd_id = 0U;
+ unsigned int state = 0U;
+
+ if (msg->in_size != sizeof(*in_args)) {
+ scmi_status_response(msg, SCMI_PROTOCOL_ERROR);
+ return;
+ }
+
+ pd_id = SPECULATION_SAFE_VALUE(in_args->pd_id);
+
+ if (pd_id >= plat_scmi_pd_count(msg->agent_id)) {
+ scmi_status_response(msg, SCMI_INVALID_PARAMETERS);
+ return;
+ }
+
+ flags = SPECULATION_SAFE_VALUE(in_args->flags);
+ state = SPECULATION_SAFE_VALUE(in_args->power_state);
+
+ status = plat_scmi_pd_set_state(msg->agent_id, flags, pd_id, state);
+
+ scmi_status_response(msg, status);
+}
+
+static const scmi_msg_handler_t scmi_pd_handler_table[] = {
+ [SCMI_PROTOCOL_VERSION] = report_version,
+ [SCMI_PROTOCOL_ATTRIBUTES] = report_attributes,
+ [SCMI_PROTOCOL_MESSAGE_ATTRIBUTES] = report_message_attributes,
+ [SCMI_PD_ATTRIBUTES] = scmi_pd_attributes,
+ [SCMI_PD_STATE_SET] = scmi_pd_state_set,
+ [SCMI_PD_STATE_GET] = scmi_pd_state_get,
+};
+
+static bool message_id_is_supported(size_t message_id)
+{
+ return (message_id < ARRAY_SIZE(scmi_pd_handler_table)) &&
+ (scmi_pd_handler_table[message_id] != NULL);
+}
+
+scmi_msg_handler_t scmi_msg_get_pd_handler(struct scmi_msg *msg)
+{
+ const size_t array_size = ARRAY_SIZE(scmi_pd_handler_table);
+ unsigned int message_id = SPECULATION_SAFE_VALUE(msg->message_id);
+
+ if (message_id >= array_size) {
+ VERBOSE("pd handle not found %u", msg->message_id);
+ return NULL;
+ }
+
+ return scmi_pd_handler_table[message_id];
+}
diff --git a/drivers/scmi-msg/power_domain.h b/drivers/scmi-msg/power_domain.h
new file mode 100644
index 0000000..48551fd
--- /dev/null
+++ b/drivers/scmi-msg/power_domain.h
@@ -0,0 +1,72 @@
+/* SPDX-License-Identifier: BSD-3-Clause */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef SCMI_MSG_PD_H
+#define SCMI_MSG_PD_H
+
+#include <stdint.h>
+
+#include <lib/utils_def.h>
+
+#define SCMI_PROTOCOL_VERSION_PD 0x21000U
+
+/*
+ * Identifiers of the SCMI POWER DOMAIN Protocol commands
+ */
+enum scmi_pd_command_id {
+ SCMI_PD_ATTRIBUTES = 0x003,
+ SCMI_PD_STATE_SET = 0x004,
+ SCMI_PD_STATE_GET = 0x005,
+};
+
+/* Protocol attributes */
+struct scmi_pd_attributes_a2p {
+ uint32_t pd_id;
+};
+
+struct scmi_protocol_attributes_p2a_pd {
+ int32_t status;
+ uint32_t attributes;
+ uint32_t statistics_addr_low;
+ uint32_t statistics_addr_high;
+ uint32_t statistics_len;
+};
+
+#define SCMI_PD_NAME_LENGTH_MAX 16U
+
+struct scmi_pd_attributes_p2a {
+ int32_t status;
+ uint32_t attributes;
+ char pd_name[SCMI_PD_NAME_LENGTH_MAX];
+};
+
+/*
+ * Power Domain State Get
+ */
+
+struct scmi_pd_state_get_a2p {
+ uint32_t pd_id;
+};
+
+struct scmi_pd_state_get_p2a {
+ int32_t status;
+ uint32_t power_state;
+};
+
+/*
+ * Power domain State Set
+ */
+
+struct scmi_pd_state_set_a2p {
+ uint32_t flags;
+ uint32_t pd_id;
+ uint32_t power_state;
+};
+
+struct scmi_pd_state_set_p2a {
+ int32_t status;
+};
+
+#endif /* SCMI_MSG_PD_H */
diff --git a/drivers/scmi-msg/smt.c b/drivers/scmi-msg/smt.c
index b08ee06..9b079c7 100644
--- a/drivers/scmi-msg/smt.c
+++ b/drivers/scmi-msg/smt.c
@@ -44,12 +44,12 @@
assert_scmi_message_max_length_fits_in_smt_buffer_slot);
/* Flag set in smt_header::status when SMT does not contain pending message */
-#define SMT_STATUS_FREE BIT(0)
+#define SMT_STATUS_FREE BIT_32(0)
/* Flag set in smt_header::status when SMT reports an error */
-#define SMT_STATUS_ERROR BIT(1)
+#define SMT_STATUS_ERROR BIT_32(1)
/* Flag set in smt_header::flags when SMT uses interrupts */
-#define SMT_FLAG_INTR_ENABLED BIT(1)
+#define SMT_FLAG_INTR_ENABLED BIT_32(1)
/* Bit fields packed in smt_header::message_header */
#define SMT_MSG_ID_MASK GENMASK_32(7, 0)
@@ -133,7 +133,7 @@
sizeof(smt_hdr->message_header);
if (in_payload_size > SCMI_PLAYLOAD_MAX) {
- VERBOSE("SCMI payload too big %u", in_payload_size);
+ VERBOSE("SCMI payload too big %zu", in_payload_size);
goto out;
}
diff --git a/include/arch/aarch64/asm_macros.S b/include/arch/aarch64/asm_macros.S
index 464c05b..7706cd8 100644
--- a/include/arch/aarch64/asm_macros.S
+++ b/include/arch/aarch64/asm_macros.S
@@ -10,10 +10,6 @@
#include <common/asm_macros_common.S>
#include <lib/spinlock.h>
-#if ENABLE_BTI && !ARM_ARCH_AT_LEAST(8, 5)
-#error Branch Target Identification requires ARM_ARCH_MINOR >= 5
-#endif
-
/*
* TLBI instruction with type specifier that implements the workaround for
* errata 813419 of Cortex-A57 or errata 1286807 of Cortex-A76.
diff --git a/include/lib/cpus/aarch64/neoverse_v1.h b/include/lib/cpus/aarch64/neoverse_v1.h
index 650eb4d..cea2659 100644
--- a/include/lib/cpus/aarch64/neoverse_v1.h
+++ b/include/lib/cpus/aarch64/neoverse_v1.h
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2019-2020, ARM Limited. All rights reserved.
+ * Copyright (c) 2019-2021, ARM Limited. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
@@ -20,4 +20,10 @@
#define NEOVERSE_V1_CPUPWRCTLR_EL1 S3_0_C15_C2_7
#define NEOVERSE_V1_CPUPWRCTLR_EL1_CORE_PWRDN_BIT U(1)
+/*******************************************************************************
+ * CPU Auxiliary Control register specific definitions.
+ ******************************************************************************/
+#define NEOVERSE_V1_ACTLR2_EL1 S3_0_C15_C1_1
+#define NEOVERSE_V1_ACTLR2_EL1_BIT_2 (ULL(1) << 2)
+
#endif /* NEOVERSE_V1_H */
diff --git a/include/lib/extensions/amu.h b/include/lib/extensions/amu.h
index 3a70e4f..3a254c9 100644
--- a/include/lib/extensions/amu.h
+++ b/include/lib/extensions/amu.h
@@ -13,6 +13,7 @@
#include <lib/cassert.h>
#include <lib/utils_def.h>
+#include <context.h>
#include <platform_def.h>
/* All group 0 counters */
@@ -80,7 +81,11 @@
};
unsigned int amu_get_version(void);
+#if __aarch64__
+void amu_enable(bool el2_unused, cpu_context_t *ctx);
+#else
void amu_enable(bool el2_unused);
+#endif
/* Group 0 configuration helpers */
uint64_t amu_group0_cnt_read(unsigned int idx);
diff --git a/lib/cpus/aarch64/neoverse_v1.S b/lib/cpus/aarch64/neoverse_v1.S
index 7336294..cee0bb7 100644
--- a/lib/cpus/aarch64/neoverse_v1.S
+++ b/lib/cpus/aarch64/neoverse_v1.S
@@ -21,6 +21,89 @@
#error "Neoverse-V1 supports only AArch64. Compile with CTX_INCLUDE_AARCH32_REGS=0"
#endif
+ /* --------------------------------------------------
+ * Errata Workaround for Neoverse V1 Errata #1791573.
+ * This applies to revisions r0p0 and r1p0, fixed in r1p1.
+ * x0: variant[4:7] and revision[0:3] of current cpu.
+ * Shall clobber: x0-x17
+ * --------------------------------------------------
+ */
+func errata_neoverse_v1_1791573_wa
+ /* Check workaround compatibility. */
+ mov x17, x30
+ bl check_errata_1791573
+ cbz x0, 1f
+
+ /* Set bit 2 in ACTLR2_EL1 */
+ mrs x1, NEOVERSE_V1_ACTLR2_EL1
+ orr x1, x1, #NEOVERSE_V1_ACTLR2_EL1_BIT_2
+ msr NEOVERSE_V1_ACTLR2_EL1, x1
+ isb
+1:
+ ret x17
+endfunc errata_neoverse_v1_1791573_wa
+
+func check_errata_1791573
+ /* Applies to r0p0 and r1p0. */
+ mov x1, #0x10
+ b cpu_rev_var_ls
+endfunc check_errata_1791573
+
+ /* --------------------------------------------------
+ * Errata Workaround for Neoverse V1 Erratum #1940577
+ * This applies to revisions r1p0 - r1p1 and is open.
+ * It also exists in r0p0 but there is no fix in that
+ * revision.
+ * Inputs:
+ * x0: variant[4:7] and revision[0:3] of current cpu.
+ * Shall clobber: x0-x17
+ * --------------------------------------------------
+ */
+func errata_neoverse_v1_1940577_wa
+ /* Compare x0 against revisions r1p0 - r1p1 */
+ mov x17, x30
+ bl check_errata_1940577
+ cbz x0, 1f
+
+ mov x0, #0
+ msr S3_6_C15_C8_0, x0
+ ldr x0, =0x10E3900002
+ msr S3_6_C15_C8_2, x0
+ ldr x0, =0x10FFF00083
+ msr S3_6_C15_C8_3, x0
+ ldr x0, =0x2001003FF
+ msr S3_6_C15_C8_1, x0
+
+ mov x0, #1
+ msr S3_6_C15_C8_0, x0
+ ldr x0, =0x10E3800082
+ msr S3_6_C15_C8_2, x0
+ ldr x0, =0x10FFF00083
+ msr S3_6_C15_C8_3, x0
+ ldr x0, =0x2001003FF
+ msr S3_6_C15_C8_1, x0
+
+ mov x0, #2
+ msr S3_6_C15_C8_0, x0
+ ldr x0, =0x10E3800200
+ msr S3_6_C15_C8_2, x0
+ ldr x0, =0x10FFF003E0
+ msr S3_6_C15_C8_3, x0
+ ldr x0, =0x2001003FF
+ msr S3_6_C15_C8_1, x0
+
+ isb
+1:
+ ret x17
+endfunc errata_neoverse_v1_1940577_wa
+
+func check_errata_1940577
+ /* Applies to revisions r1p0 - r1p1. */
+ mov x1, #0x10
+ mov x2, #0x11
+ b cpu_rev_var_range
+endfunc check_errata_1940577
+
/* ---------------------------------------------
* HW will do the cache maintenance while powering down
* ---------------------------------------------
@@ -42,6 +125,19 @@
*/
#if REPORT_ERRATA
func neoverse_v1_errata_report
+ stp x8, x30, [sp, #-16]!
+
+ bl cpu_get_rev_var
+ mov x8, x0
+
+ /*
+ * Report all errata. The revision-variant information is passed to
+ * checking functions of each errata.
+ */
+ report_errata ERRATA_V1_1791573, neoverse_v1, 1791573
+ report_errata ERRATA_V1_1940577, neoverse_v1, 1940577
+
+ ldp x8, x30, [sp], #16
ret
endfunc neoverse_v1_errata_report
#endif
@@ -51,8 +147,18 @@
/* Disable speculative loads */
msr SSBS, xzr
-
isb
+
+#if ERRATA_V1_1791573
+ mov x0, x18
+ bl errata_neoverse_v1_1791573_wa
+#endif
+
+#if ERRATA_V1_1940577
+ mov x0, x18
+ bl errata_neoverse_v1_1940577_wa
+#endif
+
ret x19
endfunc neoverse_v1_reset_func
diff --git a/lib/cpus/cpu-ops.mk b/lib/cpus/cpu-ops.mk
index b1747af..6f80d2d 100644
--- a/lib/cpus/cpu-ops.mk
+++ b/lib/cpus/cpu-ops.mk
@@ -372,6 +372,14 @@
# exists in revisions r0p0, r1p0, and r2p0 as well but there is no workaround.
ERRATA_N1_1946160 ?=0
+# Flag to apply erratum 1791573 workaround during reset. This erratum applies
+# to revisions r0p0 and r1p0 of the Neoverse V1 core, and was fixed in r1p1.
+ERRATA_V1_1791573 ?=0
+
+# Flag to apply erratum 1940577 workaround during reset. This erratum applies
+# to revisions r1p0 and r1p1 of the Neoverse V1 cpu.
+ERRATA_V1_1940577 ?=0
+
# Flag to apply DSU erratum 798953. This erratum applies to DSUs revision r0p0.
# Applying the workaround results in higher DSU power consumption on idle.
ERRATA_DSU_798953 ?=0
@@ -677,6 +685,14 @@
$(eval $(call assert_boolean,ERRATA_N1_1946160))
$(eval $(call add_define,ERRATA_N1_1946160))
+# Process ERRATA_V1_1791573 flag
+$(eval $(call assert_boolean,ERRATA_V1_1791573))
+$(eval $(call add_define,ERRATA_V1_1791573))
+
+# Process ERRATA_V1_1940577 flag
+$(eval $(call assert_boolean,ERRATA_V1_1940577))
+$(eval $(call add_define,ERRATA_V1_1940577))
+
# Process ERRATA_DSU_798953 flag
$(eval $(call assert_boolean,ERRATA_DSU_798953))
$(eval $(call add_define,ERRATA_DSU_798953))
diff --git a/lib/el3_runtime/aarch64/context.S b/lib/el3_runtime/aarch64/context.S
index d610fd4..40e7ddf 100644
--- a/lib/el3_runtime/aarch64/context.S
+++ b/lib/el3_runtime/aarch64/context.S
@@ -903,16 +903,11 @@
#if IMAGE_BL31
/* ----------------------------------------------------------
- * Restore CPTR_EL3, ZCR_EL3 for SVE support.
- * If SVE is not supported - skip the restoration.
+ * Restore CPTR_EL3.
* ZCR is only restored if SVE is supported and enabled.
* Synchronization is required before zcr_el3 is addressed.
* ----------------------------------------------------------
*/
- mrs x17, id_aa64pfr0_el1
- ubfx x17, x17, ID_AA64PFR0_SVE_SHIFT, ID_AA64PFR0_SVE_LENGTH
- cbz x17, sve_not_enabled
-
ldp x19, x20, [sp, #CTX_EL3STATE_OFFSET + CTX_CPTR_EL3]
msr cptr_el3, x19
diff --git a/lib/el3_runtime/aarch64/context_mgmt.c b/lib/el3_runtime/aarch64/context_mgmt.c
index 7a25151..7c6f953 100644
--- a/lib/el3_runtime/aarch64/context_mgmt.c
+++ b/lib/el3_runtime/aarch64/context_mgmt.c
@@ -25,6 +25,7 @@
#include <lib/extensions/twed.h>
#include <lib/utils.h>
+static void enable_extensions_secure(cpu_context_t *ctx);
/*******************************************************************************
* Context management library initialisation routine. This library is used by
@@ -178,19 +179,13 @@
* indicated by the interrupt routing model for BL31.
*/
scr_el3 |= get_scr_el3_from_routing_model(security_state);
-
-#if ENABLE_SVE_FOR_NS
- if (security_state == NON_SECURE) {
- sve_enable(ctx);
- }
#endif
-#if ENABLE_SVE_FOR_SWD
+
+ /* Save the initialized value of CPTR_EL3 register */
+ write_ctx_reg(get_el3state_ctx(ctx), CTX_CPTR_EL3, read_cptr_el3());
if (security_state == SECURE) {
- sve_enable(ctx);
+ enable_extensions_secure(ctx);
}
-#endif
-
-#endif
/*
* SCR_EL3.HCE: Enable HVC instructions if next execution state is
@@ -335,7 +330,7 @@
* When EL2 is implemented but unused `el2_unused` is non-zero, otherwise
* it is zero.
******************************************************************************/
-static void enable_extensions_nonsecure(bool el2_unused)
+static void enable_extensions_nonsecure(bool el2_unused, cpu_context_t *ctx)
{
#if IMAGE_BL31
#if ENABLE_SPE_FOR_LOWER_ELS
@@ -343,7 +338,11 @@
#endif
#if ENABLE_AMU
- amu_enable(el2_unused);
+ amu_enable(el2_unused, ctx);
+#endif
+
+#if ENABLE_SVE_FOR_NS
+ sve_enable(ctx);
#endif
#if ENABLE_MPAM_FOR_LOWER_ELS
@@ -353,6 +352,18 @@
}
/*******************************************************************************
+ * Enable architecture extensions on first entry to Secure world.
+ ******************************************************************************/
+static void enable_extensions_secure(cpu_context_t *ctx)
+{
+#if IMAGE_BL31
+#if ENABLE_SVE_FOR_SWD
+ sve_enable(ctx);
+#endif
+#endif
+}
+
+/*******************************************************************************
* The following function initializes the cpu_context for a CPU specified by
* its `cpu_idx` for first use, and sets the initial entrypoint state as
* specified by the entry_point_info structure.
@@ -586,7 +597,7 @@
write_cnthp_ctl_el2(CNTHP_CTL_RESET_VAL &
~(CNTHP_CTL_ENABLE_BIT));
}
- enable_extensions_nonsecure(el2_unused);
+ enable_extensions_nonsecure(el2_unused, ctx);
}
cm_el1_sysregs_context_restore(security_state);
diff --git a/lib/extensions/amu/aarch64/amu.c b/lib/extensions/amu/aarch64/amu.c
index 24c3737..295c0d5 100644
--- a/lib/extensions/amu/aarch64/amu.c
+++ b/lib/extensions/amu/aarch64/amu.c
@@ -46,7 +46,7 @@
* Enable counters. This function is meant to be invoked
* by the context management library before exiting from EL3.
*/
-void amu_enable(bool el2_unused)
+void amu_enable(bool el2_unused, cpu_context_t *ctx)
{
uint64_t v;
unsigned int amu_version = amu_get_version();
@@ -88,12 +88,13 @@
}
/*
- * CPTR_EL3.TAM: Set to zero so that any accesses to
+ * Retrieve and update the CPTR_EL3 value from the context mentioned
+ * in 'ctx'. Set CPTR_EL3.TAM to zero so that any accesses to
* the Activity Monitor registers do not trap to EL3.
*/
- v = read_cptr_el3();
+ v = read_ctx_reg(get_el3state_ctx(ctx), CTX_CPTR_EL3);
v &= ~TAM_BIT;
- write_cptr_el3(v);
+ write_ctx_reg(get_el3state_ctx(ctx), CTX_CPTR_EL3, v);
/* Enable group 0 counters */
write_amcntenset0_el0(AMU_GROUP0_COUNTERS_MASK);
diff --git a/lib/extensions/sve/sve.c b/lib/extensions/sve/sve.c
index 7043cc2..2702c30 100644
--- a/lib/extensions/sve/sve.c
+++ b/lib/extensions/sve/sve.c
@@ -27,11 +27,13 @@
void sve_enable(cpu_context_t *context)
{
+ u_register_t cptr_el3;
+
if (!sve_supported()) {
return;
}
- u_register_t cptr_el3 = read_cptr_el3();
+ cptr_el3 = read_ctx_reg(get_el3state_ctx(context), CTX_CPTR_EL3);
/* Enable access to SVE functionality for all ELs. */
cptr_el3 = (cptr_el3 | CPTR_EZ_BIT) & ~(TFP_BIT);
diff --git a/plat/arm/board/common/rotpk/arm_dev_rotpk.S b/plat/arm/board/common/rotpk/arm_dev_rotpk.S
index 80f2192..38f91fe 100644
--- a/plat/arm/board/common/rotpk/arm_dev_rotpk.S
+++ b/plat/arm/board/common/rotpk/arm_dev_rotpk.S
@@ -1,10 +1,17 @@
/*
- * Copyright (c) 2020, ARM Limited. All rights reserved.
+ * Copyright (c) 2021, ARM Limited. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
+/* diphda platform provides custom values for the macros defined in
+ * arm_def.h , so only platform_def.h needs to be included
+ */
+#if !defined(TARGET_PLATFORM_FVP) && !defined(TARGET_PLATFORM_FPGA)
#include "plat/arm/common/arm_def.h"
+#else
+#include <platform_def.h>
+#endif
.global arm_rotpk_header
.global arm_rotpk_header_end
diff --git a/plat/arm/board/diphda/common/diphda_bl2_mem_params_desc.c b/plat/arm/board/diphda/common/diphda_bl2_mem_params_desc.c
new file mode 100644
index 0000000..916c868
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_bl2_mem_params_desc.c
@@ -0,0 +1,86 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <common/desc_image_load.h>
+
+#include <platform_def.h>
+
+/*******************************************************************************
+ * Following descriptor provides BL image/ep information that gets used
+ * by BL2 to load the images and also subset of this information is
+ * passed to next BL image. The image loading sequence is managed by
+ * populating the images in required loading order. The image execution
+ * sequence is managed by populating the `next_handoff_image_id` with
+ * the next executable image id.
+ ******************************************************************************/
+static bl_mem_params_node_t bl2_mem_params_descs[] = {
+
+ /* Fill BL31 related information */
+ {
+ .image_id = BL31_IMAGE_ID,
+
+ SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+ VERSION_2, entry_point_info_t,
+ SECURE | EXECUTABLE | EP_FIRST_EXE),
+ .ep_info.pc = BL31_BASE,
+ .ep_info.spsr = SPSR_64(MODE_EL3, MODE_SP_ELX,
+ DISABLE_ALL_EXCEPTIONS),
+ .ep_info.args.arg3 = ARM_BL31_PLAT_PARAM_VAL,
+ SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+ VERSION_2, image_info_t, IMAGE_ATTRIB_PLAT_SETUP),
+ .image_info.image_base = BL31_BASE,
+ .image_info.image_max_size = BL31_LIMIT - BL31_BASE,
+
+ .next_handoff_image_id = BL32_IMAGE_ID,
+ },
+
+ /* Fill BL32 related information */
+ {
+ .image_id = BL32_IMAGE_ID,
+
+ SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+ VERSION_2, entry_point_info_t, SECURE | EXECUTABLE),
+ .ep_info.pc = BL32_BASE,
+ .ep_info.args.arg0 = DIPHDA_TOS_FW_CONFIG_BASE,
+ SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+ VERSION_2, image_info_t, 0),
+ .image_info.image_base = BL32_BASE,
+ .image_info.image_max_size = BL32_LIMIT - BL32_BASE,
+
+ .next_handoff_image_id = BL33_IMAGE_ID,
+ },
+
+ /* Fill TOS_FW_CONFIG related information */
+ {
+ .image_id = TOS_FW_CONFIG_ID,
+ .image_info.image_base = DIPHDA_TOS_FW_CONFIG_BASE,
+ .image_info.image_max_size = DIPHDA_TOS_FW_CONFIG_LIMIT - \
+ DIPHDA_TOS_FW_CONFIG_BASE,
+ SET_STATIC_PARAM_HEAD(ep_info, PARAM_IMAGE_BINARY,
+ VERSION_2, entry_point_info_t, SECURE | NON_EXECUTABLE),
+ SET_STATIC_PARAM_HEAD(image_info, PARAM_IMAGE_BINARY,
+ VERSION_2, image_info_t, 0),
+ .next_handoff_image_id = INVALID_IMAGE_ID,
+ },
+
+ /* Fill BL33 related information */
+ {
+ .image_id = BL33_IMAGE_ID,
+ SET_STATIC_PARAM_HEAD(ep_info, PARAM_EP,
+ VERSION_2, entry_point_info_t, NON_SECURE | EXECUTABLE),
+ .ep_info.pc = PLAT_ARM_NS_IMAGE_BASE,
+
+ SET_STATIC_PARAM_HEAD(image_info, PARAM_EP,
+ VERSION_2, image_info_t, 0),
+ .image_info.image_base = PLAT_ARM_NS_IMAGE_BASE,
+ .image_info.image_max_size = ARM_DRAM1_BASE + ARM_DRAM1_SIZE
+ - PLAT_ARM_NS_IMAGE_BASE,
+
+ .next_handoff_image_id = INVALID_IMAGE_ID,
+ },
+};
+
+REGISTER_BL_IMAGE_DESCS(bl2_mem_params_descs)
diff --git a/plat/arm/board/diphda/common/diphda_err.c b/plat/arm/board/diphda/common/diphda_err.c
new file mode 100644
index 0000000..89a3b82
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_err.c
@@ -0,0 +1,17 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <plat/arm/common/plat_arm.h>
+
+/*
+ * diphda error handler
+ */
+void __dead2 plat_arm_error_handler(int err)
+{
+ while (1) {
+ wfi();
+ }
+}
diff --git a/plat/arm/board/diphda/common/diphda_helpers.S b/plat/arm/board/diphda/common/diphda_helpers.S
new file mode 100644
index 0000000..c9d2a88
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_helpers.S
@@ -0,0 +1,67 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <arch.h>
+#include <asm_macros.S>
+#include <platform_def.h>
+
+ .globl plat_secondary_cold_boot_setup
+ .globl plat_get_my_entrypoint
+ .globl plat_is_my_cpu_primary
+ .globl plat_arm_calc_core_pos
+
+ /* --------------------------------------------------------------------
+ * void plat_secondary_cold_boot_setup (void);
+ *
+ * For AArch32, cold-booting secondary CPUs is not yet
+ * implemented and they panic.
+ * --------------------------------------------------------------------
+ */
+func plat_secondary_cold_boot_setup
+cb_panic:
+ b cb_panic
+endfunc plat_secondary_cold_boot_setup
+
+ /* ---------------------------------------------------------------------
+ * unsigned long plat_get_my_entrypoint (void);
+ *
+ * Main job of this routine is to distinguish between a cold and warm
+ * boot. On diphda, this information can be queried from the power
+ * controller. The Power Control SYS Status Register (PSYSR) indicates
+ * the wake-up reason for the CPU.
+ *
+ * For a cold boot, return 0.
+ * For a warm boot, Not yet supported.
+ *
+ * TODO: PSYSR is a common register and should be
+ * accessed using locks. Since it is not possible
+ * to use locks immediately after a cold reset
+ * we are relying on the fact that after a cold
+ * reset all cpus will read the same WK field
+ * ---------------------------------------------------------------------
+ */
+func plat_get_my_entrypoint
+ /* TODO support warm boot */
+ /* Cold reset */
+ mov x0, #0
+ ret
+endfunc plat_get_my_entrypoint
+
+ /* -----------------------------------------------------
+ * unsigned int plat_is_my_cpu_primary (void);
+ *
+ * Find out whether the current CPU is the primary
+ * CPU.
+ * -----------------------------------------------------
+ */
+func plat_is_my_cpu_primary
+ mrs x0, mpidr_el1
+ mov_imm x1, MPIDR_AFFINITY_MASK
+ and x0, x0, x1
+ cmp x0, #DIPHDA_PRIMARY_CPU
+ cset w0, eq
+ ret
+endfunc plat_is_my_cpu_primary
diff --git a/plat/arm/board/diphda/common/diphda_plat.c b/plat/arm/board/diphda/common/diphda_plat.c
new file mode 100644
index 0000000..28d15a5
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_plat.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <assert.h>
+
+#include <common/bl_common.h>
+
+#include <plat/arm/common/plat_arm.h>
+#include <plat/common/platform.h>
+#include <platform_def.h>
+
+/*
+ * Table of regions to map using the MMU.
+ * Replace or extend the below regions as required
+ */
+
+const mmap_region_t plat_arm_mmap[] = {
+ ARM_MAP_SHARED_RAM,
+ ARM_MAP_NS_SHARED_RAM,
+ ARM_MAP_NS_DRAM1,
+ DIPHDA_MAP_DEVICE,
+ DIPHDA_EXTERNAL_FLASH,
+ {0}
+};
+
+/* diphda only has one always-on power domain and there
+ * is no power control present
+ */
+void __init plat_arm_pwrc_setup(void)
+{
+}
+
+unsigned int plat_get_syscnt_freq2(void)
+{
+ /* Returning the Generic Timer Frequency */
+ return SYS_COUNTER_FREQ_IN_TICKS;
+}
+
+
+/*
+ * Helper function to initialize ARM interconnect driver.
+ */
+void plat_arm_interconnect_init(void)
+{
+}
+
+/*
+ * Helper function to place current master into coherency
+ */
+void plat_arm_interconnect_enter_coherency(void)
+{
+}
+
+/*
+ * Helper function to remove current master from coherency
+ */
+void plat_arm_interconnect_exit_coherency(void)
+{
+}
+
+/*
+ * This function is invoked during Mbed TLS library initialisation to get a heap
+ * The function simply returns the default allocated heap.
+ */
+
+#if TRUSTED_BOARD_BOOT
+int plat_get_mbedtls_heap(void **heap_addr, size_t *heap_size)
+{
+ assert(heap_addr != NULL);
+ assert(heap_size != NULL);
+
+ return arm_get_mbedtls_heap(heap_addr, heap_size);
+}
+#endif
diff --git a/plat/arm/board/diphda/common/diphda_pm.c b/plat/arm/board/diphda/common/diphda_pm.c
new file mode 100644
index 0000000..12b322e
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_pm.c
@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <lib/psci/psci.h>
+#include <plat/arm/common/plat_arm.h>
+
+/*******************************************************************************
+ * Export the platform handlers via plat_arm_psci_pm_ops. The ARM Standard
+ * platform layer will take care of registering the handlers with PSCI.
+ ******************************************************************************/
+plat_psci_ops_t plat_arm_psci_pm_ops = {
+ /* dummy struct */
+ .validate_ns_entrypoint = NULL
+};
+
+const plat_psci_ops_t *plat_arm_psci_override_pm_ops(plat_psci_ops_t *ops)
+{
+ return ops;
+}
diff --git a/plat/arm/board/diphda/common/diphda_security.c b/plat/arm/board/diphda/common/diphda_security.c
new file mode 100644
index 0000000..bf172af
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_security.c
@@ -0,0 +1,16 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+/*
+ * We assume that all security programming is done by the primary core.
+ */
+void plat_arm_security_setup(void)
+{
+ /*
+ * If the platform had additional peripheral specific security
+ * configurations, those would be configured here.
+ */
+}
diff --git a/plat/arm/board/diphda/common/diphda_stack_protector.c b/plat/arm/board/diphda/common/diphda_stack_protector.c
new file mode 100644
index 0000000..6228b63
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_stack_protector.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <stdint.h>
+
+#include <arch_helpers.h>
+#include <plat/common/platform.h>
+
+static uint32_t plat_generate_random_number(void)
+{
+ uintptr_t return_addr = (uintptr_t)__builtin_return_address(0U);
+ uintptr_t frame_addr = (uintptr_t)__builtin_frame_address(0U);
+ uint64_t cntpct = read_cntpct_el0();
+
+ /* Generate 32-bit pattern: saving the 2 least significant bytes
+ * in random_lo and random_hi
+ */
+ uint16_t random_lo = (uint16_t)(
+ (((uint64_t)return_addr) << 13) ^ frame_addr ^ cntpct
+ );
+
+ uint16_t random_hi = (uint16_t)(
+ (((uint64_t)frame_addr) << 15) ^ return_addr ^ cntpct
+ );
+
+ return (((uint32_t)random_hi) << 16) | random_lo;
+}
+
+u_register_t plat_get_stack_protector_canary(void)
+{
+ return plat_generate_random_number(); /* a 32-bit pattern returned */
+}
diff --git a/plat/arm/board/diphda/common/diphda_topology.c b/plat/arm/board/diphda/common/diphda_topology.c
new file mode 100644
index 0000000..9dfd05d
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_topology.c
@@ -0,0 +1,43 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <plat/arm/common/plat_arm.h>
+#include <plat/common/platform.h>
+
+/* The diphda power domain tree descriptor */
+static unsigned char diphda_power_domain_tree_desc[PLAT_ARM_CLUSTER_COUNT
+ + 2];
+/*******************************************************************************
+ * This function dynamically constructs the topology according to
+ * CLUSTER_COUNT and returns it.
+ ******************************************************************************/
+const unsigned char *plat_get_power_domain_tree_desc(void)
+{
+ int i;
+
+ /*
+ * The highest level is the system level. The next level is constituted
+ * by clusters and then cores in clusters.
+ */
+ diphda_power_domain_tree_desc[0] = 1;
+ diphda_power_domain_tree_desc[1] = PLAT_ARM_CLUSTER_COUNT;
+
+ for (i = 0; i < PLAT_ARM_CLUSTER_COUNT; i++)
+ diphda_power_domain_tree_desc[i + 2] = PLATFORM_CORE_COUNT;
+
+ return diphda_power_domain_tree_desc;
+}
+
+/******************************************************************************
+ * This function implements a part of the critical interface between the PSCI
+ * generic layer and the platform that allows the former to query the platform
+ * to convert an MPIDR to a unique linear index. An error code (-1) is
+ * returned in case the MPIDR is invalid.
+ *****************************************************************************/
+int plat_core_pos_by_mpidr(u_register_t mpidr)
+{
+ return plat_arm_calc_core_pos(mpidr);
+}
diff --git a/plat/arm/board/diphda/common/diphda_trusted_boot.c b/plat/arm/board/diphda/common/diphda_trusted_boot.c
new file mode 100644
index 0000000..ddb41fa
--- /dev/null
+++ b/plat/arm/board/diphda/common/diphda_trusted_boot.c
@@ -0,0 +1,53 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <plat/arm/common/plat_arm.h>
+
+/*
+ * Return the ROTPK hash in the following ASN.1 structure in DER format:
+ *
+ * AlgorithmIdentifier ::= SEQUENCE {
+ * algorithm OBJECT IDENTIFIER,
+ * parameters ANY DEFINED BY algorithm OPTIONAL
+ * }
+ *
+ * DigestInfo ::= SEQUENCE {
+ * digestAlgorithm AlgorithmIdentifier,
+ * digest OCTET STRING
+ * }
+ *
+ * The function returns 0 on success. Any other value is treated as error by the
+ * Trusted Board Boot. The function also reports extra information related
+ * to the ROTPK in the flags parameter: ROTPK_IS_HASH, ROTPK_NOT_DEPLOYED.
+ *
+ * Refer to the TF-A porting-guide document for more details.
+ */
+int plat_get_rotpk_info(void *cookie, void **key_ptr, unsigned int *key_len,
+ unsigned int *flags)
+{
+ return arm_get_rotpk_info(cookie, key_ptr, key_len, flags);
+}
+
+/*
+ * STUB overriding the non-volatile counter reading.
+ * NV counters are not implemented at this stage of development.
+ * Return: 0 = success
+ */
+int plat_get_nv_ctr(void *cookie, unsigned int *nv_ctr)
+{
+ *nv_ctr = DIPHDA_FW_NVCTR_VAL;
+ return 0;
+}
+
+/*
+ * STUB overriding the non-volatile counter updating.
+ * NV counters are not implemented at this stage of development.
+ * Return: 0 = success
+ */
+int plat_set_nv_ctr(void *cookie, unsigned int nv_ctr)
+{
+ return 0;
+}
diff --git a/plat/arm/board/diphda/common/fdts/diphda_spmc_manifest.dts b/plat/arm/board/diphda/common/fdts/diphda_spmc_manifest.dts
new file mode 100644
index 0000000..def04cd
--- /dev/null
+++ b/plat/arm/board/diphda/common/fdts/diphda_spmc_manifest.dts
@@ -0,0 +1,30 @@
+/*
+ * Copyright (c) 2021, Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+/dts-v1/;
+
+/ {
+ compatible = "arm,ffa-core-manifest-1.0";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ /*
+ * BL32 image details needed by SPMC
+ *
+ * Note:
+ * binary_size: size of BL32 + TOS_FW_CONFIG
+ */
+
+ attribute {
+ spmc_id = <0x8000>;
+ maj_ver = <0x1>;
+ min_ver = <0x0>;
+ exec_state = <0x0>;
+ load_address = <0x0 0x2002000>;
+ entrypoint = <0x0 0x2002000>;
+ binary_size = <0xae000>;
+ };
+
+};
diff --git a/plat/arm/board/diphda/common/include/platform_def.h b/plat/arm/board/diphda/common/include/platform_def.h
new file mode 100644
index 0000000..37fd71b
--- /dev/null
+++ b/plat/arm/board/diphda/common/include/platform_def.h
@@ -0,0 +1,416 @@
+/*
+ * Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef PLATFORM_DEF_H
+#define PLATFORM_DEF_H
+
+#include <common/tbbr/tbbr_img_def.h>
+#include <lib/utils_def.h>
+#include <lib/xlat_tables/xlat_tables_defs.h>
+#include <plat/arm/board/common/v2m_def.h>
+#include <plat/arm/common/arm_spm_def.h>
+#include <plat/arm/common/smccc_def.h>
+#include <plat/common/common_def.h>
+#include <plat/arm/soc/common/soc_css_def.h>
+
+#define ARM_ROTPK_HEADER_LEN 19
+#define ARM_ROTPK_HASH_LEN 32
+
+/* Special value used to verify platform parameters from BL2 to BL31 */
+#define ARM_BL31_PLAT_PARAM_VAL ULL(0x0f1e2d3c4b5a6978)
+
+/* PL011 UART related constants */
+#ifdef V2M_IOFPGA_UART0_CLK_IN_HZ
+#undef V2M_IOFPGA_UART0_CLK_IN_HZ
+#endif
+
+#ifdef V2M_IOFPGA_UART1_CLK_IN_HZ
+#undef V2M_IOFPGA_UART1_CLK_IN_HZ
+#endif
+
+#define V2M_IOFPGA_UART0_CLK_IN_HZ 50000000
+#define V2M_IOFPGA_UART1_CLK_IN_HZ 50000000
+
+/* Core/Cluster/Thread counts for diphda */
+#define DIPHDA_CLUSTER_COUNT U(1)
+#define DIPHDA_MAX_CPUS_PER_CLUSTER U(4)
+#define DIPHDA_MAX_PE_PER_CPU U(1)
+#define DIPHDA_PRIMARY_CPU U(0)
+
+#define PLAT_ARM_CLUSTER_COUNT DIPHDA_CLUSTER_COUNT
+
+#define PLATFORM_CORE_COUNT (PLAT_ARM_CLUSTER_COUNT * \
+ DIPHDA_MAX_CPUS_PER_CLUSTER * \
+ DIPHDA_MAX_PE_PER_CPU)
+
+/* UART related constants */
+#define PLAT_ARM_BOOT_UART_BASE 0x1a510000
+#define PLAT_ARM_BOOT_UART_CLK_IN_HZ V2M_IOFPGA_UART0_CLK_IN_HZ
+#define PLAT_ARM_RUN_UART_BASE 0x1a520000
+#define PLAT_ARM_RUN_UART_CLK_IN_HZ V2M_IOFPGA_UART1_CLK_IN_HZ
+#define ARM_CONSOLE_BAUDRATE 115200
+#define PLAT_ARM_CRASH_UART_BASE PLAT_ARM_RUN_UART_BASE
+#define PLAT_ARM_CRASH_UART_CLK_IN_HZ PLAT_ARM_RUN_UART_CLK_IN_HZ
+
+/* Memory related constants */
+
+/* SRAM (CVM) memory layout
+ *
+ * <ARM_TRUSTED_SRAM_BASE>
+ *
+ * partition size: sizeof(meminfo_t) = 16 bytes
+ *
+ * content: memory info area used by the next BL
+ *
+ * <ARM_FW_CONFIG_BASE>
+ *
+ * partition size: 4080 bytes
+ *
+ * <ARM_BL2_MEM_DESC_BASE>
+ *
+ * partition size: 4 KB
+ *
+ * content:
+ *
+ * Area where BL2 copies the images descriptors
+ *
+ * <ARM_BL_RAM_BASE> = <BL32_BASE>
+ *
+ * partition size: 688 KB
+ *
+ * content:
+ *
+ * BL32 (optee-os)
+ *
+ * <DIPHDA_TOS_FW_CONFIG_BASE> = 0x20ae000
+ *
+ * partition size: 8 KB
+ *
+ * content:
+ *
+ * BL32 config (TOS_FW_CONFIG)
+ *
+ * <BL31_BASE>
+ *
+ * partition size: 140 KB
+ *
+ * content:
+ *
+ * BL31
+ *
+ * <BL2_SIGNATURE_BASE>
+ *
+ * partition size: 4 KB
+ *
+ * content:
+ *
+ * MCUBOOT data needed to verify TF-A BL2
+ *
+ * <BL2_BASE>
+ *
+ * partition size: 176 KB
+ *
+ * content:
+ *
+ * BL2
+ *
+ * <ARM_NS_SHARED_RAM_BASE> = <ARM_TRUSTED_SRAM_BASE> + 1 MB
+ *
+ * partition size: 3 MB
+ *
+ * content:
+ *
+ * BL33 (u-boot)
+ */
+
+/* DDR memory */
+#define ARM_DRAM1_BASE UL(0x80000000)
+#define ARM_DRAM1_SIZE UL(0x80000000)
+#define ARM_DRAM1_END (ARM_DRAM1_BASE + \
+ ARM_DRAM1_SIZE - 1)
+
+/* DRAM1 and DRAM2 are the same for diphda */
+#define ARM_DRAM2_BASE ARM_DRAM1_BASE
+#define ARM_DRAM2_SIZE ARM_DRAM1_SIZE
+#define ARM_DRAM2_END ARM_DRAM1_END
+
+#define ARM_NS_DRAM1_BASE ARM_DRAM1_BASE
+#define ARM_NS_DRAM1_SIZE ARM_DRAM1_SIZE
+#define ARM_NS_DRAM1_END (ARM_NS_DRAM1_BASE + \
+ ARM_NS_DRAM1_SIZE - 1)
+
+/* The first 8 KB of Trusted SRAM are used as shared memory */
+#define ARM_TRUSTED_SRAM_BASE UL(0x02000000)
+#define ARM_SHARED_RAM_SIZE UL(0x00002000) /* 8 KB */
+#define ARM_SHARED_RAM_BASE ARM_TRUSTED_SRAM_BASE
+
+/* The remaining Trusted SRAM is used to load the BL images */
+
+#define PLAT_ARM_TRUSTED_SRAM_SIZE UL(0x00100000) /* 1 MB */
+
+#define PLAT_ARM_MAX_BL2_SIZE UL(0x0002d000) /* 180 KB */
+
+#define PLAT_ARM_MAX_BL31_SIZE UL(0x00023000) /* 140 KB */
+
+#define ARM_BL_RAM_BASE (ARM_SHARED_RAM_BASE + \
+ ARM_SHARED_RAM_SIZE)
+#define ARM_BL_RAM_SIZE (PLAT_ARM_TRUSTED_SRAM_SIZE - \
+ ARM_SHARED_RAM_SIZE)
+
+#define BL2_SIGNATURE_SIZE UL(0x00001000) /* 4 KB */
+#define BL2_SIGNATURE_BASE (BL2_LIMIT - \
+ PLAT_ARM_MAX_BL2_SIZE)
+#define BL2_BASE (BL2_LIMIT - \
+ PLAT_ARM_MAX_BL2_SIZE + \
+ BL2_SIGNATURE_SIZE)
+#define BL2_LIMIT (ARM_BL_RAM_BASE + \
+ ARM_BL_RAM_SIZE)
+
+#define BL31_BASE (BL2_SIGNATURE_BASE - \
+ PLAT_ARM_MAX_BL31_SIZE)
+#define BL31_LIMIT BL2_SIGNATURE_BASE
+
+#define DIPHDA_TOS_FW_CONFIG_BASE (BL31_BASE - \
+ DIPHDA_TOS_FW_CONFIG_SIZE)
+#define DIPHDA_TOS_FW_CONFIG_SIZE UL(0x00002000) /* 8 KB */
+#define DIPHDA_TOS_FW_CONFIG_LIMIT BL31_BASE
+
+#define BL32_BASE ARM_BL_RAM_BASE
+#define PLAT_ARM_MAX_BL32_SIZE (DIPHDA_TOS_FW_CONFIG_BASE - \
+ BL32_BASE) /* 688 KB */
+#define BL32_LIMIT (BL32_BASE + \
+ PLAT_ARM_MAX_BL32_SIZE)
+
+/* SPD_spmd settings */
+
+#define PLAT_ARM_SPMC_BASE BL32_BASE
+#define PLAT_ARM_SPMC_SIZE PLAT_ARM_MAX_BL32_SIZE
+
+/* NS memory */
+
+/* The last 3 MB of the SRAM is allocated to the non secure area */
+#define ARM_NS_SHARED_RAM_BASE (ARM_TRUSTED_SRAM_BASE + \
+ PLAT_ARM_TRUSTED_SRAM_SIZE)
+#define ARM_NS_SHARED_RAM_SIZE UL(0x00300000) /* 3 MB */
+
+/* end of the definition of SRAM memory layout */
+
+/* NOR Flash */
+
+#define PLAT_ARM_FIP_BASE UL(0x08131000)
+#define PLAT_ARM_FIP_MAX_SIZE UL(0x1ff000) /* 1.996 MB */
+
+#define PLAT_ARM_NVM_BASE V2M_FLASH0_BASE
+#define PLAT_ARM_NVM_SIZE UL(0x02000000) /* 32 MB */
+
+#define PLAT_ARM_FLASH_IMAGE_BASE PLAT_ARM_FIP_BASE
+#define PLAT_ARM_FLASH_IMAGE_MAX_SIZE PLAT_ARM_FIP_MAX_SIZE
+
+/*
+ * Some data must be aligned on the biggest cache line size in the platform.
+ * This is known only to the platform as it might have a combination of
+ * integrated and external caches.
+ */
+#define CACHE_WRITEBACK_GRANULE (U(1) << ARM_CACHE_WRITEBACK_SHIFT)
+#define ARM_CACHE_WRITEBACK_SHIFT 6
+
+/*
+ * Define FW_CONFIG area base and limit. Leave enough space for BL2 meminfo.
+ * FW_CONFIG is intended to host the device tree. Currently, This area is not
+ * used because diphda platform doesn't use a device tree at TF-A level.
+ */
+#define ARM_FW_CONFIG_BASE (ARM_SHARED_RAM_BASE \
+ + sizeof(meminfo_t))
+#define ARM_FW_CONFIG_LIMIT (ARM_SHARED_RAM_BASE \
+ + (ARM_SHARED_RAM_SIZE >> 1))
+
+/*
+ * Boot parameters passed from BL2 to BL31/BL32 are stored here
+ */
+#define ARM_BL2_MEM_DESC_BASE ARM_FW_CONFIG_LIMIT
+#define ARM_BL2_MEM_DESC_LIMIT ARM_BL_RAM_BASE
+
+/*
+ * The max number of regions like RO(code), coherent and data required by
+ * different BL stages which need to be mapped in the MMU.
+ */
+#define ARM_BL_REGIONS 3
+#define PLAT_ARM_MMAP_ENTRIES 8
+#define MAX_XLAT_TABLES 5
+#define MAX_MMAP_REGIONS (PLAT_ARM_MMAP_ENTRIES + \
+ ARM_BL_REGIONS)
+#define MAX_IO_DEVICES 2
+#define MAX_IO_HANDLES 3
+#define MAX_IO_BLOCK_DEVICES 1
+
+/* GIC related constants */
+#define PLAT_ARM_GICD_BASE 0x1C010000
+#define PLAT_ARM_GICC_BASE 0x1C02F000
+
+/* MHUv2 Secure Channel receiver and sender */
+#define PLAT_SDK700_MHU0_SEND 0x1B800000
+#define PLAT_SDK700_MHU0_RECV 0x1B810000
+
+/* Timer/watchdog related constants */
+#define ARM_SYS_CNTCTL_BASE UL(0x1a200000)
+#define ARM_SYS_CNTREAD_BASE UL(0x1a210000)
+#define ARM_SYS_TIMCTL_BASE UL(0x1a220000)
+
+#define SYS_COUNTER_FREQ_IN_TICKS UL(50000000) /* 50MHz */
+
+#define DIPHDA_IRQ_TZ_WDOG 32
+#define DIPHDA_IRQ_SEC_SYS_TIMER 34
+
+#define PLAT_MAX_PWR_LVL 2
+/*
+ * Macros mapping the MPIDR Affinity levels to ARM Platform Power levels. The
+ * power levels have a 1:1 mapping with the MPIDR affinity levels.
+ */
+#define ARM_PWR_LVL0 MPIDR_AFFLVL0
+#define ARM_PWR_LVL1 MPIDR_AFFLVL1
+#define ARM_PWR_LVL2 MPIDR_AFFLVL2
+
+/*
+ * Macros for local power states in ARM platforms encoded by State-ID field
+ * within the power-state parameter.
+ */
+/* Local power state for power domains in Run state. */
+#define ARM_LOCAL_STATE_RUN U(0)
+/* Local power state for retention. Valid only for CPU power domains */
+#define ARM_LOCAL_STATE_RET U(1)
+/* Local power state for OFF/power-down. Valid for CPU and cluster
+ * power domains
+ */
+#define ARM_LOCAL_STATE_OFF U(2)
+
+#define PLAT_ARM_TRUSTED_MAILBOX_BASE ARM_TRUSTED_SRAM_BASE
+#define PLAT_ARM_NSTIMER_FRAME_ID U(1)
+
+#define PLAT_ARM_NS_IMAGE_BASE (ARM_NS_SHARED_RAM_BASE)
+
+#define PLAT_PHY_ADDR_SPACE_SIZE (1ULL << 32)
+#define PLAT_VIRT_ADDR_SPACE_SIZE (1ULL << 32)
+
+/*
+ * This macro defines the deepest retention state possible. A higher state
+ * ID will represent an invalid or a power down state.
+ */
+#define PLAT_MAX_RET_STATE 1
+
+/*
+ * This macro defines the deepest power down states possible. Any state ID
+ * higher than this is invalid.
+ */
+#define PLAT_MAX_OFF_STATE 2
+
+#define PLATFORM_STACK_SIZE UL(0x440)
+
+#define DIPHDA_EXTERNAL_FLASH MAP_REGION_FLAT( \
+ PLAT_ARM_NVM_BASE, \
+ PLAT_ARM_NVM_SIZE, \
+ MT_DEVICE | MT_RO | MT_SECURE)
+
+#define ARM_MAP_SHARED_RAM MAP_REGION_FLAT( \
+ ARM_SHARED_RAM_BASE, \
+ ARM_SHARED_RAM_SIZE, \
+ MT_MEMORY | MT_RW | MT_SECURE)
+
+#define ARM_MAP_NS_SHARED_RAM MAP_REGION_FLAT( \
+ ARM_NS_SHARED_RAM_BASE, \
+ ARM_NS_SHARED_RAM_SIZE, \
+ MT_MEMORY | MT_RW | MT_NS)
+
+#define ARM_MAP_NS_DRAM1 MAP_REGION_FLAT( \
+ ARM_NS_DRAM1_BASE, \
+ ARM_NS_DRAM1_SIZE, \
+ MT_MEMORY | MT_RW | MT_NS)
+
+#define ARM_MAP_BL_RO MAP_REGION_FLAT( \
+ BL_CODE_BASE, \
+ BL_CODE_END \
+ - BL_CODE_BASE, \
+ MT_CODE | MT_SECURE), \
+ MAP_REGION_FLAT( \
+ BL_RO_DATA_BASE, \
+ BL_RO_DATA_END \
+ - BL_RO_DATA_BASE, \
+ MT_RO_DATA | MT_SECURE)
+#if USE_COHERENT_MEM
+#define ARM_MAP_BL_COHERENT_RAM MAP_REGION_FLAT( \
+ BL_COHERENT_RAM_BASE, \
+ BL_COHERENT_RAM_END \
+ - BL_COHERENT_RAM_BASE, \
+ MT_DEVICE | MT_RW | MT_SECURE)
+#endif
+
+/*
+ * Map the region for the optional device tree configuration with read and
+ * write permissions
+ */
+#define ARM_MAP_BL_CONFIG_REGION MAP_REGION_FLAT( \
+ ARM_FW_CONFIG_BASE, \
+ (ARM_FW_CONFIG_LIMIT- \
+ ARM_FW_CONFIG_BASE), \
+ MT_MEMORY | MT_RW | MT_SECURE)
+
+#define DIPHDA_DEVICE_BASE (0x1A000000)
+#define DIPHDA_DEVICE_SIZE (0x26000000)
+#define DIPHDA_MAP_DEVICE MAP_REGION_FLAT( \
+ DIPHDA_DEVICE_BASE, \
+ DIPHDA_DEVICE_SIZE, \
+ MT_DEVICE | MT_RW | MT_SECURE)
+
+#define ARM_IRQ_SEC_PHY_TIMER 29
+
+#define ARM_IRQ_SEC_SGI_0 8
+#define ARM_IRQ_SEC_SGI_1 9
+#define ARM_IRQ_SEC_SGI_2 10
+#define ARM_IRQ_SEC_SGI_3 11
+#define ARM_IRQ_SEC_SGI_4 12
+#define ARM_IRQ_SEC_SGI_5 13
+#define ARM_IRQ_SEC_SGI_6 14
+#define ARM_IRQ_SEC_SGI_7 15
+
+/*
+ * Define a list of Group 1 Secure and Group 0 interrupt properties as per GICv3
+ * terminology. On a GICv2 system or mode, the lists will be merged and treated
+ * as Group 0 interrupts.
+ */
+#define ARM_G1S_IRQ_PROPS(grp) \
+ INTR_PROP_DESC(ARM_IRQ_SEC_PHY_TIMER, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_LEVEL), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_1, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_2, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_3, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_4, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_5, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE), \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_7, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_EDGE)
+
+#define ARM_G0_IRQ_PROPS(grp) \
+ INTR_PROP_DESC(ARM_IRQ_SEC_SGI_6, GIC_HIGHEST_SEC_PRIORITY, (grp), \
+ GIC_INTR_CFG_EDGE)
+
+/*
+ * Define a list of Group 1 Secure and Group 0 interrupts as per GICv3
+ * terminology. On a GICv2 system or mode, the lists will be merged and treated
+ * as Group 0 interrupts.
+ */
+#define PLAT_ARM_G1S_IRQ_PROPS(grp) \
+ ARM_G1S_IRQ_PROPS(grp), \
+ INTR_PROP_DESC(DIPHDA_IRQ_TZ_WDOG, GIC_HIGHEST_SEC_PRIORITY, \
+ (grp), GIC_INTR_CFG_LEVEL), \
+ INTR_PROP_DESC(DIPHDA_IRQ_SEC_SYS_TIMER, \
+ GIC_HIGHEST_SEC_PRIORITY, (grp), GIC_INTR_CFG_LEVEL)
+
+#define PLAT_ARM_G0_IRQ_PROPS(grp) ARM_G0_IRQ_PROPS(grp)
+
+#endif /* PLATFORM_DEF_H */
diff --git a/plat/arm/board/diphda/include/plat_macros.S b/plat/arm/board/diphda/include/plat_macros.S
new file mode 100644
index 0000000..4de8f95
--- /dev/null
+++ b/plat/arm/board/diphda/include/plat_macros.S
@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2021, ARM Limited and Contributors. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+#ifndef PLAT_MACROS_S
+#define PLAT_MACROS_S
+
+#include <css_macros.S>
+
+/* ---------------------------------------------
+ * The below required platform porting macro
+ * prints out relevant platform registers
+ * whenever an unhandled exception is taken in
+ * BL31.
+ * ---------------------------------------------
+ */
+ .macro plat_crash_print_regs
+ css_print_gic_regs
+ .endm
+
+#endif /* PLAT_MACROS_S */
diff --git a/plat/arm/board/diphda/platform.mk b/plat/arm/board/diphda/platform.mk
new file mode 100644
index 0000000..5ff0862
--- /dev/null
+++ b/plat/arm/board/diphda/platform.mk
@@ -0,0 +1,76 @@
+#
+# Copyright (c) 2021, Arm Limited and Contributors. All rights reserved.
+#
+# SPDX-License-Identifier: BSD-3-Clause
+#
+
+# Making sure the diphda platform type is specified
+ifeq ($(filter ${TARGET_PLATFORM}, fpga fvp),)
+ $(error TARGET_PLATFORM must be fpga or fvp)
+endif
+
+DIPHDA_CPU_LIBS +=lib/cpus/aarch64/cortex_a35.S
+
+PLAT_INCLUDES := -Iplat/arm/board/diphda/common/include \
+ -Iplat/arm/board/diphda/include \
+ -Iinclude/plat/arm/common \
+ -Iinclude/plat/arm/css/common/aarch64
+
+
+DIPHDA_FW_NVCTR_VAL := 255
+TFW_NVCTR_VAL := ${DIPHDA_FW_NVCTR_VAL}
+NTFW_NVCTR_VAL := ${DIPHDA_FW_NVCTR_VAL}
+
+override NEED_BL1 := no
+
+override NEED_BL2 := yes
+FIP_BL2_ARGS := tb-fw
+
+override NEED_BL2U := no
+override NEED_BL31 := yes
+NEED_BL32 := yes
+override NEED_BL33 := yes
+
+# Include GICv2 driver files
+include drivers/arm/gic/v2/gicv2.mk
+
+DIPHDA_GIC_SOURCES := ${GICV2_SOURCES} \
+ plat/common/plat_gicv2.c \
+ plat/arm/common/arm_gicv2.c
+
+
+BL2_SOURCES += plat/arm/board/diphda/common/diphda_security.c \
+ plat/arm/board/diphda/common/diphda_err.c \
+ plat/arm/board/diphda/common/diphda_trusted_boot.c \
+ lib/utils/mem_region.c \
+ plat/arm/board/diphda/common/diphda_helpers.S \
+ plat/arm/board/diphda/common/diphda_plat.c \
+ plat/arm/board/diphda/common/diphda_bl2_mem_params_desc.c \
+ ${DIPHDA_CPU_LIBS} \
+
+
+BL31_SOURCES += drivers/cfi/v2m/v2m_flash.c \
+ lib/utils/mem_region.c \
+ plat/arm/board/diphda/common/diphda_helpers.S \
+ plat/arm/board/diphda/common/diphda_topology.c \
+ plat/arm/board/diphda/common/diphda_security.c \
+ plat/arm/board/diphda/common/diphda_plat.c \
+ plat/arm/board/diphda/common/diphda_pm.c \
+ ${DIPHDA_CPU_LIBS} \
+ ${DIPHDA_GIC_SOURCES}
+
+
+FDT_SOURCES += plat/arm/board/diphda/common/fdts/diphda_spmc_manifest.dts
+DIPHDA_TOS_FW_CONFIG := ${BUILD_PLAT}/fdts/diphda_spmc_manifest.dtb
+
+# Add the SPMC manifest to FIP and specify the same to certtool
+$(eval $(call TOOL_ADD_PAYLOAD,${DIPHDA_TOS_FW_CONFIG},--tos-fw-config,${DIPHDA_TOS_FW_CONFIG}))
+
+# Adding TARGET_PLATFORM as a GCC define (-D option)
+$(eval $(call add_define,TARGET_PLATFORM_$(call uppercase,${TARGET_PLATFORM})))
+
+# Adding DIPHDA_FW_NVCTR_VAL as a GCC define (-D option)
+$(eval $(call add_define,DIPHDA_FW_NVCTR_VAL))
+
+include plat/arm/common/arm_common.mk
+include plat/arm/board/common/board_common.mk
diff --git a/plat/arm/board/fvp/fvp_bl1_setup.c b/plat/arm/board/fvp/fvp_bl1_setup.c
index e713bbc..06ee037 100644
--- a/plat/arm/board/fvp/fvp_bl1_setup.c
+++ b/plat/arm/board/fvp/fvp_bl1_setup.c
@@ -1,15 +1,17 @@
/*
- * Copyright (c) 2013-2020, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2013-2021, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#include <assert.h>
+#include <errno.h>
#include <bl1/bl1.h>
#include <common/tbbr/tbbr_img_def.h>
#include <drivers/arm/smmu_v3.h>
#include <drivers/arm/sp805.h>
+#include <lib/mmio.h>
#include <plat/arm/common/arm_config.h>
#include <plat/arm/common/plat_arm.h>
#include <plat/arm/common/arm_def.h>
@@ -61,6 +63,12 @@
__dead2 void bl1_plat_fwu_done(void *client_cookie, void *reserved)
{
+ uint32_t nv_flags = mmio_read_32(V2M_SYS_NVFLAGS_ADDR);
+
+ /* Clear the NV flags register. */
+ mmio_write_32((V2M_SYSREGS_BASE + V2M_SYS_NVFLAGSCLR),
+ nv_flags);
+
/* Setup the watchdog to reset the system as soon as possible */
sp805_refresh(ARM_SP805_TWDG_BASE, 1U);
@@ -124,3 +132,15 @@
return 0;
}
#endif /* MEASURED_BOOT */
+
+/*******************************************************************************
+ * The following function checks if Firmware update is needed by checking error
+ * reported in NV flag.
+ ******************************************************************************/
+bool plat_arm_bl1_fwu_needed(void)
+{
+ int32_t nv_flags = (int32_t)mmio_read_32(V2M_SYS_NVFLAGS_ADDR);
+
+ /* if image load/authentication failed */
+ return ((nv_flags == -EAUTH) || (nv_flags == -ENOENT));
+}
diff --git a/plat/arm/board/fvp/fvp_common.c b/plat/arm/board/fvp/fvp_common.c
index fe0903b..9d3c031 100644
--- a/plat/arm/board/fvp/fvp_common.c
+++ b/plat/arm/board/fvp/fvp_common.c
@@ -72,14 +72,11 @@
* Table of memory regions for various BL stages to map using the MMU.
* This doesn't include Trusted SRAM as setup_page_tables() already takes care
* of mapping it.
- *
- * The flash needs to be mapped as writable in order to erase the FIP's Table of
- * Contents in case of unrecoverable error (see plat_error_handler()).
*/
#ifdef IMAGE_BL1
const mmap_region_t plat_arm_mmap[] = {
ARM_MAP_SHARED_RAM,
- V2M_MAP_FLASH0_RW,
+ V2M_MAP_FLASH0_RO,
V2M_MAP_IOFPGA,
MAP_DEVICE0,
#if FVP_INTERCONNECT_DRIVER == FVP_CCN
diff --git a/plat/arm/board/fvp/fvp_err.c b/plat/arm/board/fvp/fvp_err.c
index 2928b3a..1f9f0dd 100644
--- a/plat/arm/board/fvp/fvp_err.c
+++ b/plat/arm/board/fvp/fvp_err.c
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2019-2020, Arm Limited. All rights reserved.
+ * Copyright (c) 2019-2021, Arm Limited. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
@@ -9,6 +9,7 @@
#include <common/debug.h>
#include <drivers/arm/sp805.h>
#include <drivers/cfi/v2m_flash.h>
+#include <lib/mmio.h>
#include <plat/arm/common/plat_arm.h>
#include <platform_def.h>
@@ -17,25 +18,8 @@
*/
__dead2 void plat_arm_error_handler(int err)
{
- int ret;
-
- switch (err) {
- case -ENOENT:
- case -EAUTH:
- /* Image load or authentication error. Erase the ToC */
- INFO("Erasing FIP ToC from flash...\n");
- (void)nor_unlock(PLAT_ARM_FLASH_IMAGE_BASE);
- ret = nor_word_program(PLAT_ARM_FLASH_IMAGE_BASE, 0);
- if (ret != 0) {
- ERROR("Cannot erase ToC\n");
- } else {
- INFO("Done\n");
- }
- break;
- default:
- /* Unexpected error */
- break;
- }
+ /* Propagate the err code in the NV-flags register */
+ mmio_write_32(V2M_SYS_NVFLAGS_ADDR, (uint32_t)err);
console_flush();
diff --git a/plat/arm/board/juno/juno_bl1_setup.c b/plat/arm/board/juno/juno_bl1_setup.c
index 2234055..a9d5cc3 100644
--- a/plat/arm/board/juno/juno_bl1_setup.c
+++ b/plat/arm/board/juno/juno_bl1_setup.c
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2015-2020, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2015-2021, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
@@ -62,11 +62,11 @@
******************************************************************************/
bool plat_arm_bl1_fwu_needed(void)
{
- const int32_t *nv_flags_ptr = (const int32_t *)V2M_SYS_NVFLAGS_ADDR;
+ int32_t nv_flags = (int32_t)mmio_read_32(V2M_SYS_NVFLAGS_ADDR);
/* Check if TOC is invalid or watchdog reset happened. */
- return (!arm_io_is_toc_valid() || (((*nv_flags_ptr == -EAUTH) ||
- (*nv_flags_ptr == -ENOENT)) && is_watchdog_reset()));
+ return (!arm_io_is_toc_valid() || (((nv_flags == -EAUTH) ||
+ (nv_flags == -ENOENT)) && is_watchdog_reset()));
}
/*******************************************************************************
@@ -86,13 +86,11 @@
******************************************************************************/
__dead2 void bl1_plat_fwu_done(void *client_cookie, void *reserved)
{
- unsigned int *nv_flags_clr = (unsigned int *)
- (V2M_SYSREGS_BASE + V2M_SYS_NVFLAGSCLR);
- unsigned int *nv_flags_ptr = (unsigned int *)
- (V2M_SYSREGS_BASE + V2M_SYS_NVFLAGS);
+ uint32_t nv_flags = mmio_read_32(V2M_SYS_NVFLAGS_ADDR);
/* Clear the NV flags register. */
- *nv_flags_clr = *nv_flags_ptr;
+ mmio_write_32((V2M_SYSREGS_BASE + V2M_SYS_NVFLAGSCLR),
+ nv_flags);
/* Setup the watchdog to reset the system as soon as possible */
sp805_refresh(ARM_SP805_TWDG_BASE, 1U);
diff --git a/plat/arm/board/juno/juno_err.c b/plat/arm/board/juno/juno_err.c
index 60699cc..02d751e 100644
--- a/plat/arm/board/juno/juno_err.c
+++ b/plat/arm/board/juno/juno_err.c
@@ -1,5 +1,5 @@
/*
- * Copyright (c) 2015-2020, ARM Limited and Contributors. All rights reserved.
+ * Copyright (c) 2015-2021, ARM Limited and Contributors. All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
@@ -16,10 +16,8 @@
*/
void __dead2 plat_arm_error_handler(int err)
{
- uint32_t *flags_ptr = (uint32_t *)V2M_SYS_NVFLAGS_ADDR;
-
/* Propagate the err code in the NV-flags register */
- *flags_ptr = err;
+ mmio_write_32(V2M_SYS_NVFLAGS_ADDR, (uint32_t)err);
/* Setup the watchdog to reset the system as soon as possible */
sp805_refresh(ARM_SP805_TWDG_BASE, 1U);
diff --git a/plat/arm/board/tc0/platform.mk b/plat/arm/board/tc0/platform.mk
index 814ccd3..5ae87d1 100644
--- a/plat/arm/board/tc0/platform.mk
+++ b/plat/arm/board/tc0/platform.mk
@@ -114,6 +114,8 @@
override ENABLE_SPE_FOR_LOWER_ELS := 0
+override ENABLE_AMU := 1
+
include plat/arm/common/arm_common.mk
include plat/arm/css/common/css_common.mk
include plat/arm/soc/common/soc_css.mk
diff --git a/plat/arm/common/arm_common.mk b/plat/arm/common/arm_common.mk
index f1e4cf5..de25a53 100644
--- a/plat/arm/common/arm_common.mk
+++ b/plat/arm/common/arm_common.mk
@@ -256,8 +256,10 @@
ifeq (${JUNO_AARCH32_EL3_RUNTIME},1)
BL2_SOURCES += plat/arm/common/aarch32/arm_bl2_mem_params_desc.c
else
+ifeq ($(filter ${TARGET_PLATFORM}, fpga fvp),)
BL2_SOURCES += plat/arm/common/${ARCH}/arm_bl2_mem_params_desc.c
endif
+endif
BL2_SOURCES += plat/arm/common/arm_image_load.c \
common/desc_image_load.c
ifeq (${SPD},opteed)
diff --git a/plat/marvell/armada/a3k/common/a3700_common.mk b/plat/marvell/armada/a3k/common/a3700_common.mk
index 7d95e48..0a89742 100644
--- a/plat/marvell/armada/a3k/common/a3700_common.mk
+++ b/plat/marvell/armada/a3k/common/a3700_common.mk
@@ -74,44 +74,45 @@
ifdef WTP
$(if $(wildcard $(value WTP)/*),,$(error "'WTP=$(value WTP)' was specified, but '$(value WTP)' directory does not exist"))
-$(if $(shell test -s "$(value WTP)/branch.txt" || git -C $(value WTP) rev-parse --show-cdup 2>&1),$(error "'WTP=$(value WTP)' was specified, but '$(value WTP)' does not contain valid Marvell a3700_utils release tarball nor git repository"))
+$(if $(shell git -C $(value WTP) rev-parse --show-cdup 2>&1),$(error "'WTP=$(value WTP)' was specified, but '$(value WTP)' does not contain valid A3700-utils-marvell git repository"))
-DOIMAGEPATH := $(WTP)
-DOIMAGETOOL := $(DOIMAGEPATH)/wtptp/src/TBB_Linux/release/TBB_linux
+TBB := $(WTP)/wtptp/src/TBB_Linux/release/TBB_linux
BUILD_UART := uart-images
UART_IMAGE := $(BUILD_UART).tgz.bin
ifeq ($(MARVELL_SECURE_BOOT),1)
-DOIMAGE_CFG := $(BUILD_PLAT)/atf-tim.txt
-DOIMAGEUART_CFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-tim.txt
-IMAGESPATH := $(DOIMAGEPATH)/tim/trusted
-TIMNCFG := $(BUILD_PLAT)/atf-timN.txt
-TIMNUARTCFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-timN.txt
-TIMNSIG := $(IMAGESPATH)/timnsign.txt
-TIM2IMGARGS := -i $(DOIMAGE_CFG) -n $(TIMNCFG)
-TIMN_IMAGE := $$(grep "Image Filename:" -m 1 $(TIMNCFG) | cut -c 17-)
+TIM_CFG := $(BUILD_PLAT)/atf-tim.txt
+TIM_UART_CFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-tim.txt
+IMAGESPATH := $(WTP)/tim/trusted
+TIMN_CFG := $(BUILD_PLAT)/atf-timN.txt
+TIMN_UART_CFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-timN.txt
+TIMN_SIG := $(IMAGESPATH)/timnsign.txt
+TIM2IMGARGS := -i $(TIM_CFG) -n $(TIMN_CFG)
+TIMN_UART_IMAGE := $$(grep "Image Filename:" -m 1 $(TIMN_UART_CFG) | cut -c 17-)
else #MARVELL_SECURE_BOOT
-DOIMAGE_CFG := $(BUILD_PLAT)/atf-ntim.txt
-DOIMAGEUART_CFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-ntim.txt
-IMAGESPATH := $(DOIMAGEPATH)/tim/untrusted
-TIM2IMGARGS := -i $(DOIMAGE_CFG)
+TIM_CFG := $(BUILD_PLAT)/atf-ntim.txt
+TIM_UART_CFG := $(BUILD_PLAT)/$(BUILD_UART)/atf-ntim.txt
+IMAGESPATH := $(WTP)/tim/untrusted
+TIM2IMGARGS := -i $(TIM_CFG)
endif #MARVELL_SECURE_BOOT
-TIMBUILD := $(DOIMAGEPATH)/script/buildtim.sh
-TIM2IMG := $(DOIMAGEPATH)/script/tim2img.pl
-TIMDDRTOOL := $(DOIMAGEPATH)/tim/ddr/ddr_tool
+TIM_UART_IMAGE := $$(grep "Image Filename:" -m 1 $(TIM_UART_CFG) | cut -c 17-)
+
+TIMBUILD := $(WTP)/script/buildtim.sh
+TIM2IMG := $(WTP)/script/tim2img.pl
+TIMDDRTOOL := $(WTP)/tim/ddr/ddr_tool
$(TIMBUILD): $(TIMDDRTOOL)
# WTMI_IMG is used to specify the customized RTOS image running over
# Service CPU (CM3 processor). By the default, it points to a
# baremetal binary of fuse programming in A3700_utils.
-WTMI_IMG := $(DOIMAGEPATH)/wtmi/fuse/build/fuse.bin
+WTMI_IMG := $(WTP)/wtmi/fuse/build/fuse.bin
# WTMI_MULTI_IMG is composed of CM3 RTOS image (WTMI_IMG)
# and sys-init image.
-WTMI_MULTI_IMG := $(DOIMAGEPATH)/wtmi/build/wtmi.bin
+WTMI_MULTI_IMG := $(WTP)/wtmi/build/wtmi.bin
WTMI_ENC_IMG := wtmi-enc.bin
@@ -124,16 +125,21 @@
BOOTDEV ?= SPINOR
PARTNUM ?= 0
-TIM_IMAGE := $$(grep "Image Filename:" -m 1 $(DOIMAGE_CFG) | cut -c 17-)
-TIMBLDARGS := $(MARVELL_SECURE_BOOT) $(BOOTDEV) $(IMAGESPATH) $(DOIMAGEPATH) $(CLOCKSPRESET) \
- $(DDR_TOPOLOGY) $(PARTNUM) $(DEBUG) $(DOIMAGE_CFG) $(TIMNCFG) $(TIMNSIG) 1
-TIMBLDUARTARGS := $(MARVELL_SECURE_BOOT) UART $(IMAGESPATH) $(DOIMAGEPATH) $(CLOCKSPRESET) \
- $(DDR_TOPOLOGY) 0 0 $(DOIMAGEUART_CFG) $(TIMNUARTCFG) $(TIMNSIG) 0
+TIMBLDARGS := $(MARVELL_SECURE_BOOT) $(BOOTDEV) $(IMAGESPATH) $(WTP) $(CLOCKSPRESET) \
+ $(DDR_TOPOLOGY) $(PARTNUM) $(DEBUG) $(TIM_CFG) $(TIMN_CFG) $(TIMN_SIG) 1
+TIMBLDUARTARGS := $(MARVELL_SECURE_BOOT) UART $(IMAGESPATH) $(WTP) $(CLOCKSPRESET) \
+ $(DDR_TOPOLOGY) 0 0 $(TIM_UART_CFG) $(TIMN_UART_CFG) $(TIMN_SIG) 0
+
+UART_IMAGES := $(BUILD_UART)/$(TIM_UART_IMAGE)
+ifeq ($(MARVELL_SECURE_BOOT),1)
+UART_IMAGES += $(BUILD_UART)/$(TIMN_UART_IMAGE)
+endif
+UART_IMAGES += $(BUILD_UART)/wtmi_h.bin $(BUILD_UART)/boot-image_h.bin
CRYPTOPP_LIBDIR ?= $(CRYPTOPP_PATH)
CRYPTOPP_INCDIR ?= $(CRYPTOPP_PATH)
-$(DOIMAGETOOL): FORCE
+$(TBB): FORCE
$(if $(CRYPTOPP_LIBDIR),,$(error "Platform '$(PLAT)' for WTP image tool requires CRYPTOPP_PATH or CRYPTOPP_LIBDIR. Please set CRYPTOPP_PATH or CRYPTOPP_LIBDIR to point to the right directory"))
$(if $(CRYPTOPP_INCDIR),,$(error "Platform '$(PLAT)' for WTP image tool requires CRYPTOPP_PATH or CRYPTOPP_INCDIR. Please set CRYPTOPP_PATH or CRYPTOPP_INCDIR to point to the right directory"))
$(if $(wildcard $(CRYPTOPP_LIBDIR)/*),,$(error "Either 'CRYPTOPP_PATH' or 'CRYPTOPP_LIB' was set to '$(CRYPTOPP_LIBDIR)', but '$(CRYPTOPP_LIBDIR)' does not exist"))
@@ -141,10 +147,10 @@
ifdef CRYPTOPP_PATH
$(Q)$(MAKE) --no-print-directory -C $(CRYPTOPP_PATH) -f GNUmakefile
endif
- $(Q)$(MAKE) --no-print-directory -C $(DOIMAGEPATH)/wtptp/src/TBB_Linux -f TBB_linux.mak LIBDIR=$(CRYPTOPP_LIBDIR) INCDIR=$(CRYPTOPP_INCDIR)
+ $(Q)$(MAKE) --no-print-directory -C $(WTP)/wtptp/src/TBB_Linux -f TBB_linux.mak LIBDIR=$(CRYPTOPP_LIBDIR) INCDIR=$(CRYPTOPP_INCDIR)
$(WTMI_MULTI_IMG): FORCE
- $(Q)$(MAKE) --no-print-directory -C $(DOIMAGEPATH) WTMI_IMG=$(WTMI_IMG) DDR_TOPOLOGY=$(DDR_TOPOLOGY) CLOCKSPRESET=$(CLOCKSPRESET) WTMI
+ $(Q)$(MAKE) --no-print-directory -C $(WTP) WTMI_IMG=$(WTMI_IMG) DDR_TOPOLOGY=$(DDR_TOPOLOGY) CLOCKSPRESET=$(CLOCKSPRESET) WTMI
$(BUILD_PLAT)/wtmi.bin: $(WTMI_MULTI_IMG)
$(Q)cp -a $(WTMI_MULTI_IMG) $(BUILD_PLAT)/wtmi.bin
@@ -152,40 +158,40 @@
$(TIMDDRTOOL): FORCE
$(if $(value MV_DDR_PATH),,$(error "Platform '${PLAT}' for ddr tool requires MV_DDR_PATH. Please set MV_DDR_PATH to point to the right directory"))
$(if $(wildcard $(value MV_DDR_PATH)/*),,$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' directory does not exist"))
- $(if $(shell test -s "$(value MV_DDR_PATH)/branch.txt" || git -C $(value MV_DDR_PATH) rev-parse --show-cdup 2>&1),$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' does not contain valid Marvell mv_ddr release tarball nor git repository"))
- $(Q)$(MAKE) --no-print-directory -C $(DOIMAGEPATH) MV_DDR_PATH=$(MV_DDR_PATH) DDR_TOPOLOGY=$(DDR_TOPOLOGY) mv_ddr
+ $(if $(shell git -C $(value MV_DDR_PATH) rev-parse --show-cdup 2>&1),$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' does not contain valid mv-ddr-marvell git repository"))
+ $(Q)$(MAKE) --no-print-directory -C $(WTP) MV_DDR_PATH=$(MV_DDR_PATH) DDR_TOPOLOGY=$(DDR_TOPOLOGY) mv_ddr
-$(BUILD_PLAT)/$(UART_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(DOIMAGETOOL) $(TIMBUILD) $(TIMDDRTOOL)
+$(BUILD_PLAT)/$(UART_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(TBB) $(TIMBUILD) $(TIMDDRTOOL)
@$(ECHO_BLANK_LINE)
@echo "Building uart images"
$(Q)mkdir -p $(BUILD_PLAT)/$(BUILD_UART)
$(Q)cp -a $(BUILD_PLAT)/wtmi.bin $(BUILD_PLAT)/$(BUILD_UART)/wtmi.bin
$(Q)cp -a $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/$(BUILD_UART)/$(BOOT_IMAGE)
$(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TIMBUILD) $(TIMBLDUARTARGS)
- $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(DOIMAGEUART_CFG)
- $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(DOIMAGEUART_CFG)
+ $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIM_UART_CFG)
+ $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIM_UART_CFG)
ifeq ($(MARVELL_SECURE_BOOT),1)
- $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMNUARTCFG)
- $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMNUARTCFG)
+ $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMN_UART_CFG)
+ $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMN_UART_CFG)
endif
- $(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(DOIMAGETOOL) -r $(DOIMAGEUART_CFG) -v -D
+ $(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TBB) -r $(TIM_UART_CFG) -v -D
ifeq ($(MARVELL_SECURE_BOOT),1)
- $(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(DOIMAGETOOL) -r $(TIMNUARTCFG)
+ $(Q)cd $(BUILD_PLAT)/$(BUILD_UART) && $(TBB) -r $(TIMN_UART_CFG)
endif
- $(Q)tar czf $(BUILD_PLAT)/$(UART_IMAGE) -C $(BUILD_PLAT) $(BUILD_UART)/$(TIM_IMAGE) $(BUILD_UART)/wtmi_h.bin $(BUILD_UART)/boot-image_h.bin
+ $(Q)tar czf $(BUILD_PLAT)/$(UART_IMAGE) -C $(BUILD_PLAT) $(UART_IMAGES)
@$(ECHO_BLANK_LINE)
@echo "Built $@ successfully"
@$(ECHO_BLANK_LINE)
-$(BUILD_PLAT)/$(FLASH_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(DOIMAGETOOL) $(TIMBUILD) $(TIMDDRTOOL) $(TIM2IMG)
+$(BUILD_PLAT)/$(FLASH_IMAGE): $(BUILD_PLAT)/$(BOOT_IMAGE) $(BUILD_PLAT)/wtmi.bin $(TBB) $(TIMBUILD) $(TIMDDRTOOL) $(TIM2IMG)
@$(ECHO_BLANK_LINE)
@echo "Building flash image"
$(Q)cd $(BUILD_PLAT) && $(TIMBUILD) $(TIMBLDARGS)
- $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(DOIMAGE_CFG)
- $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(DOIMAGE_CFG)
+ $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIM_CFG)
+ $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIM_CFG)
ifeq ($(MARVELL_SECURE_BOOT),1)
- $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMNCFG)
- $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMNCFG)
+ $(Q)sed -i 's|WTMI_IMG|wtmi.bin|1' $(TIMN_CFG)
+ $(Q)sed -i 's|BOOT_IMAGE|$(BOOT_IMAGE)|1' $(TIMN_CFG)
@$(ECHO_BLANK_LINE)
@echo "=======================================================";
@echo " Secure boot. Encrypting wtmi and boot-image";
@@ -203,11 +209,11 @@
-K `cat $(IMAGESPATH)/aes-256.txt` -nosalt \
-iv `cat $(IMAGESPATH)/iv.txt` -p
endif
- $(Q)cd $(BUILD_PLAT) && $(DOIMAGETOOL) -r $(DOIMAGE_CFG) -v -D
+ $(Q)cd $(BUILD_PLAT) && $(TBB) -r $(TIM_CFG) -v -D
ifeq ($(MARVELL_SECURE_BOOT),1)
- $(Q)cd $(BUILD_PLAT) && $(DOIMAGETOOL) -r $(TIMNCFG)
- $(Q)sed -i 's|wtmi.bin|$(WTMI_ENC_IMG)|1' $(TIMNCFG)
- $(Q)sed -i 's|$(BOOT_IMAGE)|$(BOOT_ENC_IMAGE)|1' $(TIMNCFG)
+ $(Q)cd $(BUILD_PLAT) && $(TBB) -r $(TIMN_CFG)
+ $(Q)sed -i 's|wtmi.bin|$(WTMI_ENC_IMG)|1' $(TIMN_CFG)
+ $(Q)sed -i 's|$(BOOT_IMAGE)|$(BOOT_ENC_IMAGE)|1' $(TIMN_CFG)
endif
$(Q)cd $(BUILD_PLAT) && $(TIM2IMG) $(TIM2IMGARGS) -o $(BUILD_PLAT)/$(FLASH_IMAGE)
@$(ECHO_BLANK_LINE)
@@ -218,8 +224,8 @@
.PHONY: mrvl_clean
mrvl_clean:
- -$(Q)$(MAKE) --no-print-directory -C $(DOIMAGEPATH) MV_DDR_PATH=$(MV_DDR_PATH) clean
- -$(Q)$(MAKE) --no-print-directory -C $(DOIMAGEPATH)/wtptp/src/TBB_Linux -f TBB_linux.mak clean
+ -$(Q)$(MAKE) --no-print-directory -C $(WTP) MV_DDR_PATH=$(MV_DDR_PATH) clean
+ -$(Q)$(MAKE) --no-print-directory -C $(WTP)/wtptp/src/TBB_Linux -f TBB_linux.mak clean
ifdef CRYPTOPP_PATH
-$(Q)$(MAKE) --no-print-directory -C $(CRYPTOPP_PATH) -f GNUmakefile clean
endif
diff --git a/plat/marvell/armada/a3k/common/io_addr_dec.c b/plat/marvell/armada/a3k/common/io_addr_dec.c
index b27633c..fea7f81 100644
--- a/plat/marvell/armada/a3k/common/io_addr_dec.c
+++ b/plat/marvell/armada/a3k/common/io_addr_dec.c
@@ -67,17 +67,14 @@
mmio_write_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base,
win_id, dec_win->win_offset), ctrl);
- INFO("set_io_addr_dec %d result: ctrl(0x%x) base(0x%x)",
+ INFO("set_io_addr_dec %d result: ctrl(0x%x) base(0x%x) remap(0x%x)\n",
win_id, mmio_read_32(MVEBU_DEC_WIN_CTRL_REG(dec_win->dec_reg_base,
win_id, dec_win->win_offset)),
mmio_read_32(MVEBU_DEC_WIN_BASE_REG(dec_win->dec_reg_base,
- win_id, dec_win->win_offset)));
- if (win_id < dec_win->max_remap)
- INFO(" remap(%x)\n",
- mmio_read_32(MVEBU_DEC_WIN_REMAP_REG(dec_win->dec_reg_base,
- win_id, dec_win->win_offset)));
- else
- INFO("\n");
+ win_id, dec_win->win_offset)),
+ (win_id < dec_win->max_remap) ?
+ mmio_read_32(MVEBU_DEC_WIN_REMAP_REG(dec_win->dec_reg_base,
+ win_id, dec_win->win_offset)) : 0);
}
/* Set io decode window */
@@ -167,12 +164,11 @@
ERROR("Failed to set IO address decode\n");
return -1;
}
- INFO("Set IO decode window successfully, base(0x%x)",
- io_dec_win->dec_reg_base);
- INFO(" win_attr(%x) max_dram_win(%d) max_remap(%d)",
+ INFO("Set IO decode window successfully, base(0x%x)"
+ " win_attr(%x) max_dram_win(%d) max_remap(%d)"
+ " win_offset(%d)\n", io_dec_win->dec_reg_base,
io_dec_win->win_attr, io_dec_win->max_dram_win,
- io_dec_win->max_remap);
- INFO(" win_offset(%d)\n", io_dec_win->win_offset);
+ io_dec_win->max_remap, io_dec_win->win_offset);
}
return 0;
diff --git a/plat/marvell/armada/a8k/common/a8k_common.mk b/plat/marvell/armada/a8k/common/a8k_common.mk
index 90883f2..773b912 100644
--- a/plat/marvell/armada/a8k/common/a8k_common.mk
+++ b/plat/marvell/armada/a8k/common/a8k_common.mk
@@ -82,6 +82,7 @@
PLAT_INCLUDES := -I$(BOARD_DIR) \
-I$(BOARD_DIR)/board \
+ -I$(CURDIR)/drivers/marvell \
-I$(PLAT_COMMON_BASE)/include \
-I$(PLAT_INCLUDE_BASE)/common
diff --git a/plat/marvell/armada/a8k/common/ble/ble.mk b/plat/marvell/armada/a8k/common/ble/ble.mk
index d6d72c1..87e2ce0 100644
--- a/plat/marvell/armada/a8k/common/ble/ble.mk
+++ b/plat/marvell/armada/a8k/common/ble/ble.mk
@@ -3,8 +3,6 @@
# SPDX-License-Identifier: BSD-3-Clause
# https://spdx.org/licenses
-MV_DDR_PATH ?= drivers/marvell/mv_ddr
-
MV_DDR_LIB = $(BUILD_PLAT)/ble/mv_ddr_lib.a
LIBC_LIB = $(BUILD_PLAT)/lib/libc.a
BLE_LIBS = $(MV_DDR_LIB) $(LIBC_LIB)
@@ -18,14 +16,19 @@
$(PLAT_MARVELL)/common/plat_delay_timer.c \
$(PLAT_MARVELL)/common/marvell_console.c
-PLAT_INCLUDES += -I$(MV_DDR_PATH) \
- -I$(CURDIR)/include \
+MV_DDR_INCLUDES := -I$(CURDIR)/include \
-I$(CURDIR)/include/arch/aarch64 \
-I$(CURDIR)/include/lib/libc \
- -I$(CURDIR)/include/lib/libc/aarch64 \
- -I$(CURDIR)/drivers/marvell
+ -I$(CURDIR)/include/lib/libc/aarch64
BLE_LINKERFILE := $(BLE_PATH)/ble.ld.S
+BLE_OBJS := $(addprefix $(BUILD_PLAT)/ble/,$(call SOURCES_TO_OBJS,$(BLE_SOURCES)))
+$(BLE_OBJS): PLAT_INCLUDES += -I$(MV_DDR_PATH)
+$(BLE_OBJS): $(MV_DDR_LIB)
+
$(MV_DDR_LIB): FORCE
- @+make -C $(MV_DDR_PATH) --no-print-directory PLAT_INCLUDES="$(PLAT_INCLUDES)" PLATFORM=$(PLAT) ARCH=AARCH64 OBJ_DIR=$(BUILD_PLAT)/ble
+ $(if $(value MV_DDR_PATH),,$(error "Platform '$(PLAT)' for BLE requires MV_DDR_PATH. Please set MV_DDR_PATH to point to the right directory"))
+ $(if $(wildcard $(value MV_DDR_PATH)/*),,$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' directory does not exist"))
+ $(if $(shell git -C $(value MV_DDR_PATH) rev-parse --show-cdup 2>&1),$(error "'MV_DDR_PATH=$(value MV_DDR_PATH)' was specified, but '$(value MV_DDR_PATH)' does not contain valid mv-ddr-marvell git repository"))
+ @+make -C $(MV_DDR_PATH) --no-print-directory PLAT_INCLUDES="$(MV_DDR_INCLUDES)" PLATFORM=$(PLAT) ARCH=AARCH64 OBJ_DIR=$(BUILD_PLAT)/ble
diff --git a/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.c b/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.c
index 307862d..2d67fdf 100644
--- a/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.c
+++ b/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.c
@@ -143,6 +143,11 @@
blocked |= SPM_COND_CHECK_BLOCKED_PLL;
}
+ if (is_system_suspend && (blocked != 0U)) {
+ INFO("suspend: %s total blocked = 0x%08x\n",
+ dest->name, blocked);
+ }
+
return blocked;
}
diff --git a/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.h b/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.h
index ba13fe3..91ebdd9 100644
--- a/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.h
+++ b/plat/mediatek/mt8192/drivers/spm/mt_spm_cond.h
@@ -23,20 +23,11 @@
PLAT_SPM_COND_MAX,
};
-enum PLAT_SPM_COND_PLL {
- PLAT_SPM_COND_PLL_UNIVPLL = 0,
- PLAT_SPM_COND_PLL_MFGPLL,
- PLAT_SPM_COND_PLL_MSDCPLL,
- PLAT_SPM_COND_PLL_TVDPLL,
- PLAT_SPM_COND_PLL_MMPLL,
- PLAT_SPM_COND_PLL_MAX,
-};
-
-#define PLL_BIT_MFGPLL (PLAT_SPM_COND_PLL_MFGPLL)
-#define PLL_BIT_MMPLL (PLAT_SPM_COND_PLL_MMPLL)
-#define PLL_BIT_UNIVPLL (PLAT_SPM_COND_PLL_UNIVPLL)
-#define PLL_BIT_MSDCPLL (PLAT_SPM_COND_PLL_MSDCPLL)
-#define PLL_BIT_TVDPLL (PLAT_SPM_COND_PLL_TVDPLL)
+#define PLL_BIT_UNIVPLL BIT(0)
+#define PLL_BIT_MFGPLL BIT(1)
+#define PLL_BIT_MSDCPLL BIT(2)
+#define PLL_BIT_TVDPLL BIT(3)
+#define PLL_BIT_MMPLL BIT(4)
/* Definition about SPM_COND_CHECK_BLOCKED
* bit [00 ~ 15]: cg blocking index
diff --git a/plat/mediatek/mt8195/bl31_plat_setup.c b/plat/mediatek/mt8195/bl31_plat_setup.c
index 39c1918..8745454 100644
--- a/plat/mediatek/mt8195/bl31_plat_setup.c
+++ b/plat/mediatek/mt8195/bl31_plat_setup.c
@@ -19,6 +19,7 @@
#include <mt_gic_v3.h>
#include <mt_spm.h>
#include <mt_timer.h>
+#include <mtk_dcm.h>
#include <mtgpio.h>
#include <plat_params.h>
#include <plat_private.h>
@@ -84,6 +85,11 @@
******************************************************************************/
void bl31_platform_setup(void)
{
+ /* Set dcm on */
+ if (!dcm_set_default()) {
+ ERROR("Failed to set default dcm on!!\n");
+ }
+
/* Initialize the GIC driver, CPU and distributor interfaces */
mt_gic_driver_init();
mt_gic_init();
diff --git a/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.c b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.c
new file mode 100644
index 0000000..aed0833
--- /dev/null
+++ b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.c
@@ -0,0 +1,63 @@
+/*
+ * Copyright (c) 2021, MediaTek Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <mtk_dcm.h>
+#include <mtk_dcm_utils.h>
+
+static void dcm_armcore(bool mode)
+{
+ dcm_mp_cpusys_top_bus_pll_div_dcm(mode);
+ dcm_mp_cpusys_top_cpu_pll_div_0_dcm(mode);
+ dcm_mp_cpusys_top_cpu_pll_div_1_dcm(mode);
+}
+
+static void dcm_mcusys(bool on)
+{
+ dcm_mp_cpusys_top_adb_dcm(on);
+ dcm_mp_cpusys_top_apb_dcm(on);
+ dcm_mp_cpusys_top_cpubiu_dcm(on);
+ dcm_mp_cpusys_top_misc_dcm(on);
+ dcm_mp_cpusys_top_mp0_qdcm(on);
+ dcm_cpccfg_reg_emi_wfifo(on);
+ dcm_mp_cpusys_top_last_cor_idle_dcm(on);
+}
+
+static void dcm_stall(bool on)
+{
+ dcm_mp_cpusys_top_core_stall_dcm(on);
+ dcm_mp_cpusys_top_fcm_stall_dcm(on);
+}
+
+static bool check_dcm_state(void)
+{
+ bool ret = true;
+
+ ret &= dcm_mp_cpusys_top_bus_pll_div_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_cpu_pll_div_0_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_cpu_pll_div_1_dcm_is_on();
+
+ ret &= dcm_mp_cpusys_top_adb_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_apb_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_cpubiu_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_misc_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_mp0_qdcm_is_on();
+ ret &= dcm_cpccfg_reg_emi_wfifo_is_on();
+ ret &= dcm_mp_cpusys_top_last_cor_idle_dcm_is_on();
+
+ ret &= dcm_mp_cpusys_top_core_stall_dcm_is_on();
+ ret &= dcm_mp_cpusys_top_fcm_stall_dcm_is_on();
+
+ return ret;
+}
+
+bool dcm_set_default(void)
+{
+ dcm_armcore(true);
+ dcm_mcusys(true);
+ dcm_stall(true);
+
+ return check_dcm_state();
+}
diff --git a/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.h b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.h
new file mode 100644
index 0000000..cb65b85
--- /dev/null
+++ b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright (c) 2021, MediaTek Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef MTK_DCM_H
+#define MTK_DCM_H
+
+#include <stdbool.h>
+
+bool dcm_set_default(void);
+
+#endif /* #ifndef MTK_DCM_H */
diff --git a/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.c b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.c
new file mode 100644
index 0000000..a1a3720
--- /dev/null
+++ b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.c
@@ -0,0 +1,483 @@
+/*
+ * Copyright (c) 2021, MediaTek Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#include <lib/mmio.h>
+#include <lib/utils_def.h>
+#include <mtk_dcm_utils.h>
+
+#define MP_CPUSYS_TOP_ADB_DCM_REG0_MASK (BIT(17))
+#define MP_CPUSYS_TOP_ADB_DCM_REG1_MASK (BIT(15) | \
+ BIT(16) | \
+ BIT(17) | \
+ BIT(18) | \
+ BIT(21))
+#define MP_CPUSYS_TOP_ADB_DCM_REG2_MASK (BIT(15) | \
+ BIT(16) | \
+ BIT(17) | \
+ BIT(18))
+#define MP_CPUSYS_TOP_ADB_DCM_REG0_ON (BIT(17))
+#define MP_CPUSYS_TOP_ADB_DCM_REG1_ON (BIT(15) | \
+ BIT(16) | \
+ BIT(17) | \
+ BIT(18) | \
+ BIT(21))
+#define MP_CPUSYS_TOP_ADB_DCM_REG2_ON (BIT(15) | \
+ BIT(16) | \
+ BIT(17) | \
+ BIT(18))
+#define MP_CPUSYS_TOP_ADB_DCM_REG0_OFF ((0x0 << 17))
+#define MP_CPUSYS_TOP_ADB_DCM_REG1_OFF ((0x0 << 15) | \
+ (0x0 << 16) | \
+ (0x0 << 17) | \
+ (0x0 << 18) | \
+ (0x0 << 21))
+#define MP_CPUSYS_TOP_ADB_DCM_REG2_OFF ((0x0 << 15) | \
+ (0x0 << 16) | \
+ (0x0 << 17) | \
+ (0x0 << 18))
+
+bool dcm_mp_cpusys_top_adb_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG0) &
+ MP_CPUSYS_TOP_ADB_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_ADB_DCM_REG0_ON);
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG4) &
+ MP_CPUSYS_TOP_ADB_DCM_REG1_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_ADB_DCM_REG1_ON);
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0) &
+ MP_CPUSYS_TOP_ADB_DCM_REG2_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_ADB_DCM_REG2_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_adb_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_adb_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG0,
+ MP_CPUSYS_TOP_ADB_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG0_ON);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG4,
+ MP_CPUSYS_TOP_ADB_DCM_REG1_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG1_ON);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0,
+ MP_CPUSYS_TOP_ADB_DCM_REG2_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG2_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_adb_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG0,
+ MP_CPUSYS_TOP_ADB_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG0_OFF);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_ADB_DCM_CFG4,
+ MP_CPUSYS_TOP_ADB_DCM_REG1_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG1_OFF);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0,
+ MP_CPUSYS_TOP_ADB_DCM_REG2_MASK,
+ MP_CPUSYS_TOP_ADB_DCM_REG2_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_APB_DCM_REG0_MASK (BIT(5))
+#define MP_CPUSYS_TOP_APB_DCM_REG1_MASK (BIT(8))
+#define MP_CPUSYS_TOP_APB_DCM_REG2_MASK (BIT(16))
+#define MP_CPUSYS_TOP_APB_DCM_REG0_ON (BIT(5))
+#define MP_CPUSYS_TOP_APB_DCM_REG1_ON (BIT(8))
+#define MP_CPUSYS_TOP_APB_DCM_REG2_ON (BIT(16))
+#define MP_CPUSYS_TOP_APB_DCM_REG0_OFF ((0x0 << 5))
+#define MP_CPUSYS_TOP_APB_DCM_REG1_OFF ((0x0 << 8))
+#define MP_CPUSYS_TOP_APB_DCM_REG2_OFF ((0x0 << 16))
+
+bool dcm_mp_cpusys_top_apb_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0) &
+ MP_CPUSYS_TOP_APB_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_APB_DCM_REG0_ON);
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0) &
+ MP_CPUSYS_TOP_APB_DCM_REG1_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_APB_DCM_REG1_ON);
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP0_DCM_CFG0) &
+ MP_CPUSYS_TOP_APB_DCM_REG2_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_APB_DCM_REG2_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_apb_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_apb_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG0_ON);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG1_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG1_ON);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG2_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG2_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_apb_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG0_OFF);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCUSYS_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG1_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG1_OFF);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG0,
+ MP_CPUSYS_TOP_APB_DCM_REG2_MASK,
+ MP_CPUSYS_TOP_APB_DCM_REG2_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_MASK (BIT(11) | \
+ BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_ON (BIT(11) | \
+ BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_OFF ((0x0 << 11) | \
+ (0x0 << 24) | \
+ (0x0 << 25))
+
+bool dcm_mp_cpusys_top_bus_pll_div_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG) &
+ MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_bus_pll_div_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_bus_pll_div_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG,
+ MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_bus_pll_div_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG,
+ MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_BUS_PLL_DIV_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_MASK (BIT(0))
+#define MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_ON (BIT(0))
+#define MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_OFF ((0x0 << 0))
+
+bool dcm_mp_cpusys_top_core_stall_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP0_DCM_CFG7) &
+ MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_core_stall_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_core_stall_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG7,
+ MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_core_stall_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG7,
+ MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CORE_STALL_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_CPUBIU_DCM_REG0_MASK ((0xffff << 0))
+#define MP_CPUSYS_TOP_CPUBIU_DCM_REG0_ON ((0xffff << 0))
+#define MP_CPUSYS_TOP_CPUBIU_DCM_REG0_OFF ((0x0 << 0))
+
+bool dcm_mp_cpusys_top_cpubiu_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MCSIC_DCM0) &
+ MP_CPUSYS_TOP_CPUBIU_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_CPUBIU_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_cpubiu_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_cpubiu_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCSIC_DCM0,
+ MP_CPUSYS_TOP_CPUBIU_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPUBIU_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_cpubiu_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MCSIC_DCM0,
+ MP_CPUSYS_TOP_CPUBIU_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPUBIU_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_MASK (BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_ON (BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_OFF ((0x0 << 24) | \
+ (0x0 << 25))
+
+bool dcm_mp_cpusys_top_cpu_pll_div_0_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG0) &
+ MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_cpu_pll_div_0_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_cpu_pll_div_0_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG0,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_cpu_pll_div_0_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG0,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_0_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_MASK (BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_ON (BIT(24) | \
+ BIT(25))
+#define MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_OFF ((0x0 << 24) | \
+ (0x0 << 25))
+
+bool dcm_mp_cpusys_top_cpu_pll_div_1_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG1) &
+ MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_cpu_pll_div_1_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_cpu_pll_div_1_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG1,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_cpu_pll_div_1_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_CPU_PLLDIV_CFG1,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_CPU_PLL_DIV_1_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_MASK (BIT(4))
+#define MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_ON (BIT(4))
+#define MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_OFF ((0x0 << 4))
+
+bool dcm_mp_cpusys_top_fcm_stall_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP0_DCM_CFG7) &
+ MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_fcm_stall_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_fcm_stall_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG7,
+ MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_fcm_stall_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG7,
+ MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_FCM_STALL_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_MASK ((0x1U << 31))
+#define MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_ON ((0x1U << 31))
+#define MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_OFF ((0x0U << 31))
+
+bool dcm_mp_cpusys_top_last_cor_idle_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG) &
+ MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_last_cor_idle_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_last_cor_idle_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG,
+ MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_last_cor_idle_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_BUS_PLLDIV_CFG,
+ MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_LAST_COR_IDLE_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_MISC_DCM_REG0_MASK (BIT(1) | \
+ BIT(4))
+#define MP_CPUSYS_TOP_MISC_DCM_REG0_ON (BIT(1) | \
+ BIT(4))
+#define MP_CPUSYS_TOP_MISC_DCM_REG0_OFF ((0x0 << 1) | \
+ (0x0 << 4))
+
+bool dcm_mp_cpusys_top_misc_dcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0) &
+ MP_CPUSYS_TOP_MISC_DCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_MISC_DCM_REG0_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_misc_dcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_misc_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_MISC_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_MISC_DCM_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_misc_dcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_MISC_DCM_REG0_MASK,
+ MP_CPUSYS_TOP_MISC_DCM_REG0_OFF);
+ }
+}
+
+#define MP_CPUSYS_TOP_MP0_QDCM_REG0_MASK (BIT(3))
+#define MP_CPUSYS_TOP_MP0_QDCM_REG1_MASK (BIT(0) | \
+ BIT(1) | \
+ BIT(2) | \
+ BIT(3))
+#define MP_CPUSYS_TOP_MP0_QDCM_REG0_ON (BIT(3))
+#define MP_CPUSYS_TOP_MP0_QDCM_REG1_ON (BIT(0) | \
+ BIT(1) | \
+ BIT(2) | \
+ BIT(3))
+#define MP_CPUSYS_TOP_MP0_QDCM_REG0_OFF ((0x0 << 3))
+#define MP_CPUSYS_TOP_MP0_QDCM_REG1_OFF ((0x0 << 0) | \
+ (0x0 << 1) | \
+ (0x0 << 2) | \
+ (0x0 << 3))
+
+bool dcm_mp_cpusys_top_mp0_qdcm_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0) &
+ MP_CPUSYS_TOP_MP0_QDCM_REG0_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_MP0_QDCM_REG0_ON);
+ ret &= ((mmio_read_32(MP_CPUSYS_TOP_MP0_DCM_CFG0) &
+ MP_CPUSYS_TOP_MP0_QDCM_REG1_MASK) ==
+ (unsigned int) MP_CPUSYS_TOP_MP0_QDCM_REG1_ON);
+
+ return ret;
+}
+
+void dcm_mp_cpusys_top_mp0_qdcm(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'mp_cpusys_top_mp0_qdcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_MP0_QDCM_REG0_MASK,
+ MP_CPUSYS_TOP_MP0_QDCM_REG0_ON);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG0,
+ MP_CPUSYS_TOP_MP0_QDCM_REG1_MASK,
+ MP_CPUSYS_TOP_MP0_QDCM_REG1_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'mp_cpusys_top_mp0_qdcm'" */
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP_MISC_DCM_CFG0,
+ MP_CPUSYS_TOP_MP0_QDCM_REG0_MASK,
+ MP_CPUSYS_TOP_MP0_QDCM_REG0_OFF);
+ mmio_clrsetbits_32(MP_CPUSYS_TOP_MP0_DCM_CFG0,
+ MP_CPUSYS_TOP_MP0_QDCM_REG1_MASK,
+ MP_CPUSYS_TOP_MP0_QDCM_REG1_OFF);
+ }
+}
+
+#define CPCCFG_REG_EMI_WFIFO_REG0_MASK (BIT(0) | \
+ BIT(1) | \
+ BIT(2) | \
+ BIT(3))
+#define CPCCFG_REG_EMI_WFIFO_REG0_ON (BIT(0) | \
+ BIT(1) | \
+ BIT(2) | \
+ BIT(3))
+#define CPCCFG_REG_EMI_WFIFO_REG0_OFF ((0x0 << 0) | \
+ (0x0 << 1) | \
+ (0x0 << 2) | \
+ (0x0 << 3))
+
+bool dcm_cpccfg_reg_emi_wfifo_is_on(void)
+{
+ bool ret = true;
+
+ ret &= ((mmio_read_32(CPCCFG_REG_EMI_WFIFO) &
+ CPCCFG_REG_EMI_WFIFO_REG0_MASK) ==
+ (unsigned int) CPCCFG_REG_EMI_WFIFO_REG0_ON);
+
+ return ret;
+}
+
+void dcm_cpccfg_reg_emi_wfifo(bool on)
+{
+ if (on) {
+ /* TINFO = "Turn ON DCM 'cpccfg_reg_emi_wfifo'" */
+ mmio_clrsetbits_32(CPCCFG_REG_EMI_WFIFO,
+ CPCCFG_REG_EMI_WFIFO_REG0_MASK,
+ CPCCFG_REG_EMI_WFIFO_REG0_ON);
+ } else {
+ /* TINFO = "Turn OFF DCM 'cpccfg_reg_emi_wfifo'" */
+ mmio_clrsetbits_32(CPCCFG_REG_EMI_WFIFO,
+ CPCCFG_REG_EMI_WFIFO_REG0_MASK,
+ CPCCFG_REG_EMI_WFIFO_REG0_OFF);
+ }
+}
diff --git a/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.h b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.h
new file mode 100644
index 0000000..e5743af
--- /dev/null
+++ b/plat/mediatek/mt8195/drivers/dcm/mtk_dcm_utils.h
@@ -0,0 +1,59 @@
+/*
+ * Copyright (c) 2021, MediaTek Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef MTK_DCM_UTILS_H
+#define MTK_DCM_UTILS_H
+
+#include <stdbool.h>
+
+#include <mtk_dcm.h>
+#include <platform_def.h>
+
+/* Base */
+#define MP_CPUSYS_TOP_BASE (MCUCFG_BASE + 0x8000)
+#define CPCCFG_REG_BASE (MCUCFG_BASE + 0xA800)
+
+/* Register Definition */
+#define MP_CPUSYS_TOP_CPU_PLLDIV_CFG0 (MP_CPUSYS_TOP_BASE + 0x22a0)
+#define MP_CPUSYS_TOP_CPU_PLLDIV_CFG1 (MP_CPUSYS_TOP_BASE + 0x22a4)
+#define MP_CPUSYS_TOP_BUS_PLLDIV_CFG (MP_CPUSYS_TOP_BASE + 0x22e0)
+#define MP_CPUSYS_TOP_MCSIC_DCM0 (MP_CPUSYS_TOP_BASE + 0x2440)
+#define MP_CPUSYS_TOP_MP_ADB_DCM_CFG0 (MP_CPUSYS_TOP_BASE + 0x2500)
+#define MP_CPUSYS_TOP_MP_ADB_DCM_CFG4 (MP_CPUSYS_TOP_BASE + 0x2510)
+#define MP_CPUSYS_TOP_MP_MISC_DCM_CFG0 (MP_CPUSYS_TOP_BASE + 0x2518)
+#define MP_CPUSYS_TOP_MCUSYS_DCM_CFG0 (MP_CPUSYS_TOP_BASE + 0x25c0)
+#define CPCCFG_REG_EMI_WFIFO (CPCCFG_REG_BASE + 0x100)
+#define MP_CPUSYS_TOP_MP0_DCM_CFG0 (MP_CPUSYS_TOP_BASE + 0x4880)
+#define MP_CPUSYS_TOP_MP0_DCM_CFG7 (MP_CPUSYS_TOP_BASE + 0x489c)
+
+/* MP_CPUSYS_TOP */
+bool dcm_mp_cpusys_top_adb_dcm_is_on(void);
+void dcm_mp_cpusys_top_adb_dcm(bool on);
+bool dcm_mp_cpusys_top_apb_dcm_is_on(void);
+void dcm_mp_cpusys_top_apb_dcm(bool on);
+bool dcm_mp_cpusys_top_bus_pll_div_dcm_is_on(void);
+void dcm_mp_cpusys_top_bus_pll_div_dcm(bool on);
+bool dcm_mp_cpusys_top_core_stall_dcm_is_on(void);
+void dcm_mp_cpusys_top_core_stall_dcm(bool on);
+bool dcm_mp_cpusys_top_cpubiu_dcm_is_on(void);
+void dcm_mp_cpusys_top_cpubiu_dcm(bool on);
+bool dcm_mp_cpusys_top_cpu_pll_div_0_dcm_is_on(void);
+void dcm_mp_cpusys_top_cpu_pll_div_0_dcm(bool on);
+bool dcm_mp_cpusys_top_cpu_pll_div_1_dcm_is_on(void);
+void dcm_mp_cpusys_top_cpu_pll_div_1_dcm(bool on);
+bool dcm_mp_cpusys_top_fcm_stall_dcm_is_on(void);
+void dcm_mp_cpusys_top_fcm_stall_dcm(bool on);
+bool dcm_mp_cpusys_top_last_cor_idle_dcm_is_on(void);
+void dcm_mp_cpusys_top_last_cor_idle_dcm(bool on);
+bool dcm_mp_cpusys_top_misc_dcm_is_on(void);
+void dcm_mp_cpusys_top_misc_dcm(bool on);
+bool dcm_mp_cpusys_top_mp0_qdcm_is_on(void);
+void dcm_mp_cpusys_top_mp0_qdcm(bool on);
+/* CPCCFG_REG */
+bool dcm_cpccfg_reg_emi_wfifo_is_on(void);
+void dcm_cpccfg_reg_emi_wfifo(bool on);
+
+#endif
diff --git a/plat/mediatek/mt8195/platform.mk b/plat/mediatek/mt8195/platform.mk
index 481e9ad..f4604c4 100644
--- a/plat/mediatek/mt8195/platform.mk
+++ b/plat/mediatek/mt8195/platform.mk
@@ -14,7 +14,8 @@
-I${MTK_PLAT}/common/drivers/timer/ \
-I${MTK_PLAT}/common/drivers/uart/ \
-I${MTK_PLAT}/common/lpm/ \
- -I${MTK_PLAT_SOC}/drivers/dp/ \
+ -I${MTK_PLAT_SOC}/drivers/dcm \
+ -I${MTK_PLAT_SOC}/drivers/dp/ \
-I${MTK_PLAT_SOC}/drivers/gpio/ \
-I${MTK_PLAT_SOC}/drivers/mcdi/ \
-I${MTK_PLAT_SOC}/drivers/pmic/ \
@@ -56,6 +57,8 @@
${MTK_PLAT_SOC}/aarch64/platform_common.c \
${MTK_PLAT_SOC}/aarch64/plat_helpers.S \
${MTK_PLAT_SOC}/bl31_plat_setup.c \
+ ${MTK_PLAT_SOC}/drivers/dcm/mtk_dcm.c \
+ ${MTK_PLAT_SOC}/drivers/dcm/mtk_dcm_utils.c \
${MTK_PLAT_SOC}/drivers/dp/mt_dp.c \
${MTK_PLAT_SOC}/drivers/gpio/mtgpio.c \
${MTK_PLAT_SOC}/drivers/mcdi/mt_cpu_pm.c \
diff --git a/plat/nxp/soc-lx2160a/soc.def b/plat/nxp/soc-lx2160a/soc.def
index bd0dd15..24d1d13 100644
--- a/plat/nxp/soc-lx2160a/soc.def
+++ b/plat/nxp/soc-lx2160a/soc.def
@@ -91,7 +91,7 @@
# Location of BL2 on OCRAM
BL2_BASE_ADDR := $(shell echo $$(( $(OCRAM_START_ADDR) + $(NXP_ROM_RSVD) + $(CSF_HDR_SZ) )))
# Covert to HEX to be used by create_pbl.mk
-BL2_BASE := $$(echo "obase=16; ${BL2_BASE_ADDR}" | bc)
+BL2_BASE := $(shell echo "0x"$$(echo "obase=16; ${BL2_BASE_ADDR}" | bc))
# BL2_HDR_LOC is at (OCRAM_ADDR + NXP_ROM_RSVD)
# This value BL2_HDR_LOC + CSF_HDR_SZ should not overalp with BL2_BASE
@@ -107,95 +107,5 @@
# SoC Errata
ERRATA_SOC_A050426 := 1
-ifneq (${CACHE_LINE},)
-$(eval $(call add_define_val,PLATFORM_CACHE_LINE_SHIFT,${CACHE_LINE}))
-$(eval CACHE_WRITEBACK_GRANULE=$(shell echo $$((1 << $(CACHE_LINE)))))
-$(eval $(call add_define_val,CACHE_WRITEBACK_GRANULE,$(CACHE_WRITEBACK_GRANULE)))
-endif
-
-ifneq (${INTERCONNECT},)
-$(eval $(call add_define,NXP_HAS_CCN508))
-endif
-
-ifneq (${CHASSIS},)
-$(eval $(call add_define,CONFIG_CHASSIS_${CHASSIS}))
-endif
-
-ifneq (${PLAT_DDR_PHY},)
-$(eval $(call add_define,NXP_DDR_${PLAT_DDR_PHY}))
-endif
-
-ifneq (${PHYS_SYS},)
-$(eval $(call add_define,CONFIG_PHYS_64BIT))
-endif
-
-ifneq (${CSF_HDR_SZ},)
-$(eval $(call add_define_val,CSF_HDR_SZ,${CSF_HDR_SZ}))
-endif
-
-ifneq (${OCRAM_START_ADDR},)
-$(eval $(call add_define_val,NXP_OCRAM_ADDR,${OCRAM_START_ADDR}))
-endif
-
-ifneq (${OCRAM_SIZE},)
-$(eval $(call add_define_val,NXP_OCRAM_SIZE,${OCRAM_SIZE}))
-endif
-
-ifneq (${NXP_ROM_RSVD},)
-$(eval $(call add_define_val,NXP_ROM_RSVD,${NXP_ROM_RSVD}))
-endif
-
-ifneq (${BL2_BASE_ADDR},)
-$(eval $(call add_define_val,BL2_BASE,${BL2_BASE_ADDR}))
-endif
-
-ifeq (${SEC_MEM_NON_COHERENT},yes)
-$(eval $(call add_define,SEC_MEM_NON_COHERENT))
-endif
-
-ifneq (${NXP_ESDHC_ENDIANNESS},)
-$(eval $(call add_define,NXP_ESDHC_${NXP_ESDHC_ENDIANNESS}))
-endif
-
-ifneq (${NXP_SFP_VER},)
-$(eval $(call add_define,NXP_SFP_VER_${NXP_SFP_VER}))
-endif
-
-ifneq (${NXP_SFP_ENDIANNESS},)
-$(eval $(call add_define,NXP_SFP_${NXP_SFP_ENDIANNESS}))
-endif
-
-ifneq (${NXP_GPIO_ENDIANNESS},)
-$(eval $(call add_define,NXP_GPIO_${NXP_GPIO_ENDIANNESS}))
-endif
-
-ifneq (${NXP_SNVS_ENDIANNESS},)
-$(eval $(call add_define,NXP_SNVS_${NXP_SNVS_ENDIANNESS}))
-endif
-
-ifneq (${NXP_GUR_ENDIANNESS},)
-$(eval $(call add_define,NXP_GUR_${NXP_GUR_ENDIANNESS}))
-endif
-
-ifneq (${NXP_FSPI_ENDIANNESS},)
-$(eval $(call add_define,NXP_FSPI_${NXP_FSPI_ENDIANNESS}))
-endif
-
# enable dynamic memory mapping
PLAT_XLAT_TABLES_DYNAMIC := 1
-
-ifneq (${NXP_SEC_ENDIANNESS},)
-$(eval $(call add_define,NXP_SEC_${NXP_SEC_ENDIANNESS}))
-endif
-
-ifneq (${NXP_DDR_ENDIANNESS},)
-$(eval $(call add_define,NXP_DDR_${NXP_DDR_ENDIANNESS}))
-endif
-
-ifneq (${NXP_DDR_INTLV_256B},)
-$(eval $(call add_define,NXP_DDR_INTLV_256B))
-endif
-
-ifneq (${PLAT_XLAT_TABLES_DYNAMIC},)
-$(eval $(call add_define,PLAT_XLAT_TABLES_DYNAMIC))
-endif
diff --git a/plat/nxp/soc-lx2160a/soc.mk b/plat/nxp/soc-lx2160a/soc.mk
index b9649b4..8ab1430 100644
--- a/plat/nxp/soc-lx2160a/soc.mk
+++ b/plat/nxp/soc-lx2160a/soc.mk
@@ -15,7 +15,7 @@
# get SoC-specific defnitions
include ${PLAT_SOC_PATH}/soc.def
-
+include ${PLAT_COMMON_PATH}/plat_make_helper/soc_common_def.mk
include ${PLAT_COMMON_PATH}/plat_make_helper/plat_build_macros.mk
# SoC-specific
diff --git a/plat/rockchip/rk3399/drivers/dram/dram.h b/plat/rockchip/rk3399/drivers/dram/dram.h
index 0eb12cf..5572b16 100644
--- a/plat/rockchip/rk3399/drivers/dram/dram.h
+++ b/plat/rockchip/rk3399/drivers/dram/dram.h
@@ -149,7 +149,7 @@
uint32_t rx_cal_dqs[2][4];
};
-extern __sramdata struct rk3399_sdram_params sdram_config;
+extern struct rk3399_sdram_params sdram_config;
void dram_init(void);
