| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Google Pompom board device tree source |
| * |
| * Copyright 2020 Google LLC. |
| */ |
| |
| #include "sc7180.dtsi" |
| |
| ap_ec_spi: &spi6 {}; |
| ap_h1_spi: &spi0 {}; |
| |
| #include "sc7180-trogdor.dtsi" |
| |
| / { |
| panel: panel { |
| compatible = "kingdisplay,kd116n21-30nv-a010"; |
| power-supply = <&pp3300_dx_edp>; |
| backlight = <&backlight>; |
| hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>; |
| |
| ports { |
| port { |
| panel_in_edp: endpoint { |
| remote-endpoint = <&sn65dsi86_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &ap_sar_sensor { |
| compatible = "semtech,sx9311"; |
| status = "okay"; |
| }; |
| |
| ap_ts_pen_1v8: &i2c4 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| ap_ts: touchscreen@10 { |
| compatible = "hid-over-i2c"; |
| reg = <0x10>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| |
| post-power-on-delay-ms = <20>; |
| hid-descr-addr = <0x0001>; |
| |
| vdd-supply = <&pp3300_ts>; |
| }; |
| }; |
| |
| &gpio_keys { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| }; |
| |
| &sound { |
| compatible = "qcom,sc7180-sndcard-rt5682-m98357-2mic"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dmic_sel>; |
| dmic-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| /* PINCTRL - board-specific pinctrl */ |
| |
| &tlmm { |
| gpio-line-names = "TP_INT_ODL", |
| "AP_RAM_ID0", |
| "AP_SKU_ID2", |
| "AP_RAM_ID1", |
| "", |
| "AP_RAM_ID2", |
| "AP_TP_I2C_SDA", |
| "AP_TP_I2C_SCL", |
| "TS_RESET_L", |
| "TS_INT_L", |
| "", |
| "EDP_BRIJ_IRQ", |
| "AP_EDP_BKLTEN", |
| "", |
| "", |
| "EDP_BRIJ_I2C_SDA", |
| "EDP_BRIJ_I2C_SCL", |
| "HUB_RST_L", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AMP_EN", |
| "P_SENSOR_INT_L", |
| "AP_SAR_SENSOR_SDA", |
| "AP_SAR_SENSOR_SCL", |
| "", |
| "HP_IRQ", |
| "", |
| "EN_PP3300_DX_EDP", |
| "AP_BRD_ID2", |
| "BRIJ_SUSPEND", |
| "AP_BRD_ID0", |
| "AP_H1_SPI_MISO", |
| "AP_H1_SPI_MOSI", |
| "AP_H1_SPI_CLK", |
| "AP_H1_SPI_CS_L", |
| "", |
| "", |
| "", |
| "", |
| "H1_AP_INT_ODL", |
| "", |
| "UART_AP_TX_DBG_RX", |
| "UART_DBG_TX_AP_RX", |
| "HP_I2C_SDA", |
| "HP_I2C_SCL", |
| "FORCED_USB_BOOT", |
| "AMP_BCLK", |
| "AMP_LRCLK", |
| "AMP_DIN", |
| "PEN_PDCT_L", |
| "HP_BCLK", |
| "HP_LRCLK", |
| "HP_DOUT", |
| "HP_DIN", |
| "HP_MCLK", |
| "AP_SKU_ID0", |
| "AP_EC_SPI_MISO", |
| "AP_EC_SPI_MOSI", |
| "AP_EC_SPI_CLK", |
| "AP_EC_SPI_CS_L", |
| "AP_SPI_CLK", |
| "AP_SPI_MOSI", |
| "AP_SPI_MISO", |
| /* |
| * AP_FLASH_WP_L is crossystem ABI. Schematics |
| * call it BIOS_FLASH_WP_L. |
| */ |
| "AP_FLASH_WP_L", |
| "", |
| "AP_SPI_CS0_L", |
| "SD_CD_ODL", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "UIM2_DATA", |
| "UIM2_CLK", |
| "UIM2_RST", |
| "UIM2_PRESENT", |
| "UIM1_DATA", |
| "UIM1_CLK", |
| "UIM1_RST", |
| "", |
| "EN_PP3300_CODEC", |
| "EN_PP3300_HUB", |
| "DMIC_SEL", |
| "", |
| "", |
| "", |
| "", |
| "AP_SKU_ID1", |
| "AP_RST_REQ", |
| "", |
| "AP_BRD_ID1", |
| "AP_EC_INT_R_L", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "EDP_BRIJ_EN", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "", |
| "AP_TS_PEN_I2C_SDA", |
| "AP_TS_PEN_I2C_SCL", |
| "DP_HOT_PLUG_DET", |
| "EC_IN_RW_ODL"; |
| |
| dmic_sel: dmic-sel { |
| pinmux { |
| pins = "gpio86"; |
| function = "gpio"; |
| }; |
| |
| pinconf { |
| pins = "gpio86"; |
| bias-pull-down; |
| }; |
| }; |
| }; |
