| /** |
| ****************************************************************************** |
| * @file stm32l5xx_hal_gpio.c |
| * @author MCD Application Team |
| * @brief GPIO HAL module driver. |
| * This file provides firmware functions to manage the following |
| * functionalities of the General Purpose Input/Output (GPIO) peripheral: |
| * + Initialization and de-initialization functions |
| * + IO operation functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### GPIO Peripheral features ##### |
| ============================================================================== |
| [..] |
| (+) Each port bit of the general-purpose I/O (GPIO) ports can be individually |
| configured by software in several modes: |
| (++) Input mode |
| (++) Analog mode |
| (++) Output mode |
| (++) Alternate function mode |
| (++) External interrupt/event lines |
| |
| (+) During and just after reset, the alternate functions and external interrupt |
| lines are not active and the I/O ports are configured in input floating mode. |
| |
| (+) All GPIO pins have weak internal pull-up and pull-down resistors, which can be |
| activated or not. |
| |
| (+) In Output or Alternate mode, each IO can be configured on open-drain or push-pull |
| type and the IO speed can be selected depending on the VDD value. |
| |
| (+) The microcontroller IO pins are connected to onboard peripherals/modules through a |
| multiplexer that allows only one peripheral alternate function (AF) connected |
| to an IO pin at a time. In this way, there can be no conflict between peripherals |
| sharing the same IO pin. |
| |
| (+) All ports have external interrupt/event capability. To use external interrupt |
| lines, the port must be configured in input mode. All available GPIO pins are |
| connected to the 16 external interrupt/event lines from EXTI0 to EXTI15. |
| |
| (+) The external interrupt/event controller consists of up to 39 edge detectors |
| (16 lines are connected to GPIO) for generating event/interrupt requests (each |
| input line can be independently configured to select the type (interrupt or event) |
| and the corresponding trigger event (rising or falling or both). Each line can |
| also be masked independently. |
| |
| ##### How to use this driver ##### |
| ============================================================================== |
| [..] |
| (#) Enable the GPIO AHB clock using the following function: __HAL_RCC_GPIOx_CLK_ENABLE(). |
| |
| (#) Configure the GPIO pin(s) using HAL_GPIO_Init(). |
| (++) Configure the IO mode using "Mode" member from GPIO_InitTypeDef structure |
| (++) Activate Pull-up, Pull-down resistor using "Pull" member from GPIO_InitTypeDef |
| structure. |
| (++) In case of Output or alternate function mode selection: the speed is |
| configured through "Speed" member from GPIO_InitTypeDef structure. |
| (++) In alternate mode is selection, the alternate function connected to the IO |
| is configured through "Alternate" member from GPIO_InitTypeDef structure. |
| (++) Analog mode is required when a pin is to be used as ADC channel |
| or DAC output. |
| (++) In case of external interrupt/event selection the "Mode" member from |
| GPIO_InitTypeDef structure select the type (interrupt or event) and |
| the corresponding trigger event (rising or falling or both). |
| |
| (#) In case of external interrupt/event mode selection, configure NVIC IRQ priority |
| mapped to the EXTI line using HAL_NVIC_SetPriority() and enable it using |
| HAL_NVIC_EnableIRQ(). |
| |
| (#) To get the level of a pin configured in input mode use HAL_GPIO_ReadPin(). |
| |
| (#) To set/reset the level of a pin configured in output mode use |
| HAL_GPIO_WritePin()/HAL_GPIO_TogglePin(). |
| |
| (#) To lock pin configuration until next reset use HAL_GPIO_LockPin(). |
| |
| (#) During and just after reset, the alternate functions are not |
| active and the GPIO pins are configured in input floating mode (except JTAG |
| pins). |
| |
| (#) The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as general purpose |
| (PC14 and PC15, respectively) when the LSE oscillator is off. The LSE has |
| priority over the GPIO function. |
| |
| (#) The HSE oscillator pins OSC_IN/OSC_OUT can be used as |
| general purpose PH0 and PH1, respectively, when the HSE oscillator is off. |
| The HSE has priority over the GPIO function. |
| |
| @endverbatim |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© Copyright (c) 2019 STMicroelectronics. |
| * All rights reserved.</center></h2> |
| * |
| * This software component is licensed by ST under BSD 3-Clause license, |
| * the "License"; You may not use this file except in compliance with the |
| * License. You may obtain a copy of the License at: |
| * opensource.org/licenses/BSD-3-Clause |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32l5xx_hal.h" |
| |
| /** @addtogroup STM32L5xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @addtogroup GPIO |
| * @{ |
| */ |
| |
| #ifdef HAL_GPIO_MODULE_ENABLED |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private defines -----------------------------------------------------------*/ |
| /** @defgroup GPIO_Private_Defines GPIO Private Defines |
| * @{ |
| */ |
| #define GPIO_MODE (0x00000003U) |
| #define EXTI_MODE (0x10000000U) |
| #define GPIO_MODE_IT (0x00010000U) |
| #define GPIO_MODE_EVT (0x00020000U) |
| #define RISING_EDGE (0x00100000U) |
| #define FALLING_EDGE (0x00200000U) |
| #define GPIO_OUTPUT_TYPE (0x00000010U) |
| |
| #define GPIO_NUMBER (16U) |
| /** |
| * @} |
| */ |
| |
| /* Private macros ------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /* Exported functions --------------------------------------------------------*/ |
| |
| /** @addtogroup GPIO_Exported_Functions |
| * @{ |
| */ |
| |
| /** @addtogroup GPIO_Exported_Functions_Group1 |
| * @brief Initialization and Configuration functions |
| * |
| @verbatim |
| =============================================================================== |
| ##### Initialization and de-initialization functions ##### |
| =============================================================================== |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initialize the GPIOx peripheral according to the specified parameters in the GPIO_Init. |
| * @note If GPIOx peripheral pin is used in EXTI_MODE and the pin is secure in case |
| * the system implements the security (TZEN=1), it is up to the secure application to |
| * insure that the corresponding EXTI line is set secure. |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Init pointer to a GPIO_InitTypeDef structure that contains |
| * the configuration information for the specified GPIO peripheral. |
| * @retval None |
| */ |
| void HAL_GPIO_Init(GPIO_TypeDef *GPIOx, GPIO_InitTypeDef *GPIO_Init) |
| { |
| uint32_t position = 0U; |
| uint32_t iocurrent; |
| uint32_t temp; |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_PIN(GPIO_Init->Pin)); |
| assert_param(IS_GPIO_MODE(GPIO_Init->Mode)); |
| assert_param(IS_GPIO_PULL(GPIO_Init->Pull)); |
| |
| /* Configure the port pins */ |
| while (((GPIO_Init->Pin) >> position) != 0U) |
| { |
| /* Get current io position */ |
| iocurrent = (GPIO_Init->Pin) & (1UL << position); |
| |
| if(iocurrent != 0U) |
| { |
| /*--------------------- GPIO Mode Configuration ------------------------*/ |
| /* In case of Output or Alternate function mode selection */ |
| if((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) || |
| (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) |
| { |
| /* Check the Speed parameter */ |
| assert_param(IS_GPIO_SPEED(GPIO_Init->Speed)); |
| /* Configure the IO Speed */ |
| temp = GPIOx->OSPEEDR; |
| temp &= ~(GPIO_OSPEEDR_OSPEED0 << (position * 2U)); |
| temp |= (GPIO_Init->Speed << (position * 2U)); |
| GPIOx->OSPEEDR = temp; |
| |
| /* Configure the IO Output Type */ |
| temp = GPIOx->OTYPER; |
| temp &= ~(GPIO_OTYPER_OT0 << position) ; |
| temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4) << position); |
| GPIOx->OTYPER = temp; |
| } |
| |
| /* Activate the Pull-up or Pull down resistor for the current IO */ |
| temp = GPIOx->PUPDR; |
| temp &= ~(GPIO_PUPDR_PUPD0 << (position * 2U)); |
| temp |= ((GPIO_Init->Pull) << (position * 2U)); |
| GPIOx->PUPDR = temp; |
| |
| /* In case of Alternate function mode selection */ |
| if((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD)) |
| { |
| /* Check the Alternate function parameters */ |
| assert_param(IS_GPIO_AF_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_AF(GPIO_Init->Alternate)); |
| |
| /* Configure Alternate function mapped with the current IO */ |
| temp = GPIOx->AFR[position >> 3U]; |
| temp &= ~(0x0FUL << ((position & 0x07U) * 4U)) ; |
| temp |= ((GPIO_Init->Alternate) << ((position & 0x07U) * 4U)); |
| GPIOx->AFR[position >> 3U] = temp; |
| } |
| |
| /* Configure IO Direction mode (Input, Output, Alternate or Analog) */ |
| temp = GPIOx->MODER; |
| temp &= ~(GPIO_MODER_MODE0 << (position * 2U)); |
| temp |= ((GPIO_Init->Mode & GPIO_MODE) << (position * 2U)); |
| GPIOx->MODER = temp; |
| |
| /*--------------------- EXTI Mode Configuration ------------------------*/ |
| /* Configure the External Interrupt or event for the current IO */ |
| if((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE) |
| { |
| temp = EXTI->EXTICR[position >> 2U]; |
| temp &= ~((0x0FU) << (8U * (position & 0x03U))); |
| temp |= (GPIO_GET_INDEX(GPIOx) << (8U * (position & 0x03U))); |
| EXTI->EXTICR[position >> 2U] = temp; |
| |
| /* Clear EXTI line configuration */ |
| temp = EXTI->IMR1; |
| temp &= ~(iocurrent); |
| if((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT) |
| { |
| temp |= iocurrent; |
| } |
| EXTI->IMR1 = temp; |
| |
| temp = EXTI->EMR1; |
| temp &= ~(iocurrent); |
| if((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT) |
| { |
| temp |= iocurrent; |
| } |
| EXTI->EMR1 = temp; |
| |
| /* Clear Rising Falling edge configuration */ |
| temp = EXTI->RTSR1; |
| temp &= ~(iocurrent); |
| if((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE) |
| { |
| temp |= iocurrent; |
| } |
| EXTI->RTSR1 = temp; |
| |
| temp = EXTI->FTSR1; |
| temp &= ~(iocurrent); |
| if((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE) |
| { |
| temp |= iocurrent; |
| } |
| EXTI->FTSR1 = temp; |
| } |
| } |
| |
| position++; |
| } |
| } |
| |
| /** |
| * @brief De-initialize the GPIOx peripheral registers to their default reset values. |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the port bit to be written. |
| * This parameter can be one of GPIO_PIN_x where x can be (0..15). |
| * @retval None |
| */ |
| void HAL_GPIO_DeInit(GPIO_TypeDef *GPIOx, uint32_t GPIO_Pin) |
| { |
| uint32_t position = 0U; |
| uint32_t iocurrent; |
| uint32_t temp; |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| |
| /* Configure the port pins */ |
| while ((GPIO_Pin >> position) != 0U) |
| { |
| /* Get current io position */ |
| iocurrent = (GPIO_Pin) & (1UL << position); |
| |
| if (iocurrent != 0U) |
| { |
| /*------------------------- EXTI Mode Configuration --------------------*/ |
| /* Clear the External Interrupt or Event for the current IO */ |
| |
| temp = EXTI->EXTICR[position >> 2U]; |
| temp &= ((0x0FUL) << (8U * (position & 0x03U))); |
| if(temp == (GPIO_GET_INDEX(GPIOx) << (8U * (position & 0x03U)))) |
| { |
| /* Clear EXTI line configuration */ |
| EXTI->IMR1 &= ~(iocurrent); |
| EXTI->EMR1 &= ~(iocurrent); |
| |
| /* Clear Rising Falling edge configuration */ |
| EXTI->RTSR1 &= ~(iocurrent); |
| EXTI->FTSR1 &= ~(iocurrent); |
| |
| temp = (0x0FUL) << (8U * (position & 0x03U)); |
| EXTI->EXTICR[position >> 2U] &= ~temp; |
| } |
| |
| /*------------------------- GPIO Mode Configuration --------------------*/ |
| /* Configure IO in Analog Mode */ |
| GPIOx->MODER |= (GPIO_MODER_MODE0 << (position * 2U)); |
| |
| /* Configure the default Alternate Function in current IO */ |
| GPIOx->AFR[position >> 3U] &= ~(0x0FUL << ((position & 0x07U) * 4U)) ; |
| |
| /* Configure the default value for IO Speed */ |
| GPIOx->OSPEEDR &= ~(GPIO_OSPEEDR_OSPEED0 << (position * 2U)); |
| |
| /* Configure the default value IO Output Type */ |
| GPIOx->OTYPER &= ~(GPIO_OTYPER_OT0 << position) ; |
| |
| /* Deactivate the Pull-up and Pull-down resistor for the current IO */ |
| GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPD0 << (position * 2U)); |
| } |
| |
| position++; |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup GPIO_Exported_Functions_Group2 |
| * @brief GPIO Read, Write, Toggle, Lock and EXTI management functions. |
| * |
| @verbatim |
| =============================================================================== |
| ##### IO operation functions ##### |
| =============================================================================== |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Read the specified input port pin. |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the port bit to read. |
| * This parameter can be any combination of GPIO_Pin_x where x can be (0..15). |
| * @retval The input port pin value. |
| */ |
| GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin) |
| { |
| GPIO_PinState bitstatus; |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| |
| if((GPIOx->IDR & GPIO_Pin) != 0U) |
| { |
| bitstatus = GPIO_PIN_SET; |
| } |
| else |
| { |
| bitstatus = GPIO_PIN_RESET; |
| } |
| return bitstatus; |
| } |
| |
| /** |
| * @brief Set or clear the selected data port bit. |
| * |
| * @note This function uses GPIOx_BSRR and GPIOx_BRR registers to allow atomic read/modify |
| * accesses. In this way, there is no risk of an IRQ occurring between |
| * the read and the modify access. |
| * |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the port bit to be written. |
| * This parameter can be any combination of GPIO_Pin_x where x can be (0..15). |
| * @param PinState specifies the value to be written to the selected bit. |
| * This parameter can be one of the GPIO_PinState enum values: |
| * @arg GPIO_PIN_RESET: to clear the port pin |
| * @arg GPIO_PIN_SET: to set the port pin |
| * @retval None |
| */ |
| void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState) |
| { |
| /* Check the parameters */ |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| assert_param(IS_GPIO_PIN_ACTION(PinState)); |
| |
| if (PinState != GPIO_PIN_RESET) |
| { |
| GPIOx->BSRR = (uint32_t)GPIO_Pin; |
| } |
| else |
| { |
| GPIOx->BRR = (uint32_t)GPIO_Pin; |
| } |
| } |
| |
| /** |
| * @brief Toggle the specified GPIO pin. |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the pin to be toggled. |
| * This parameter can be any combination of GPIO_Pin_x where x can be (0..15). |
| * @retval None |
| */ |
| void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin) |
| { |
| /* Check the parameters */ |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| |
| if ((GPIOx->ODR & GPIO_Pin) != 0U) |
| { |
| GPIOx->BRR = (uint32_t)GPIO_Pin; |
| } |
| else |
| { |
| GPIOx->BSRR = (uint32_t)GPIO_Pin; |
| } |
| } |
| |
| /** |
| * @brief Lock GPIO Pins configuration registers. |
| * @note The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR, |
| * GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH. |
| * @note The configuration of the locked GPIO pins can no longer be modified |
| * until the next reset. |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the port bits to be locked. |
| * This parameter can be any combination of GPIO_Pin_x where x can be (0..15). |
| * @retval None |
| */ |
| HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin) |
| { |
| __IO uint32_t temp = GPIO_LCKR_LCKK; |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_LOCK_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| |
| /* Apply lock key write sequence */ |
| temp |= GPIO_Pin; |
| /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ |
| GPIOx->LCKR = temp; |
| /* Reset LCKx bit(s): LCKK='0' + LCK[15-0] */ |
| GPIOx->LCKR = GPIO_Pin; |
| /* Set LCKx bit(s): LCKK='1' + LCK[15-0] */ |
| GPIOx->LCKR = temp; |
| /* Read LCKK register. This read is mandatory to complete key lock sequence */ |
| temp = GPIOx->LCKR; |
| |
| /* read again in order to confirm lock is active */ |
| if ((GPIOx->LCKR & GPIO_LCKR_LCKK) != 0U) |
| { |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Handle EXTI interrupt request. |
| * @param GPIO_Pin Specifies the port pin connected to corresponding EXTI line. |
| * @retval None |
| */ |
| void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin) |
| { |
| /* EXTI line interrupt detected */ |
| if(__HAL_GPIO_EXTI_GET_RISING_IT(GPIO_Pin) != 0U) |
| { |
| __HAL_GPIO_EXTI_CLEAR_RISING_IT(GPIO_Pin); |
| HAL_GPIO_EXTI_Rising_Callback(GPIO_Pin); |
| } |
| |
| if(__HAL_GPIO_EXTI_GET_FALLING_IT(GPIO_Pin) != 0U) |
| { |
| __HAL_GPIO_EXTI_CLEAR_FALLING_IT(GPIO_Pin); |
| HAL_GPIO_EXTI_Falling_Callback(GPIO_Pin); |
| } |
| } |
| |
| /** |
| * @brief EXTI line rising detection callback. |
| * @param GPIO_Pin Specifies the port pin connected to corresponding EXTI line. |
| * @retval None |
| */ |
| __weak void HAL_GPIO_EXTI_Rising_Callback(uint16_t GPIO_Pin) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(GPIO_Pin); |
| |
| /* NOTE: This function should not be modified, when the callback is needed, |
| the HAL_GPIO_EXTI_Rising_Callback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief EXTI line falling detection callback. |
| * @param GPIO_Pin Specifies the port pin connected to corresponding EXTI line. |
| * @retval None |
| */ |
| __weak void HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(GPIO_Pin); |
| |
| /* NOTE: This function should not be modified, when the callback is needed, |
| the HAL_GPIO_EXTI_Falling_Callback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #if defined (__ARM_FEATURE_CMSE) && (__ARM_FEATURE_CMSE == 3U) |
| |
| /** @defgroup GPIO_Exported_Functions_Group3 IO attributes management functions |
| * @brief GPIO attributes management functions. |
| * |
| @verbatim |
| =============================================================================== |
| ##### IO attributes functions ##### |
| =============================================================================== |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Configure the GPIO pins attributes. |
| * @note Available attributes are to secure GPIO pin(s), so this function is |
| * only available in secure |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the pin(s) to configure the secure attribute |
| * @param PinAttributes specifies the pin(s) to be set in secure mode, other being set non secured. |
| * @retval None |
| */ |
| void HAL_GPIO_ConfigPinAttributes(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, uint32_t PinAttributes) |
| { |
| uint32_t position = 0U; |
| uint32_t iocurrent; |
| uint32_t temp; |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_PIN(GPIO_Pin)); |
| assert_param(IS_GPIO_PIN_ATTRIBUTES(PinAttributes)); |
| |
| temp = GPIOx->SECCFGR; |
| |
| /* Configure the port pins */ |
| while ((GPIO_Pin >> position) != 0U) |
| { |
| /* Get current io position */ |
| iocurrent = GPIO_Pin & (1UL << position); |
| |
| if(iocurrent != 0U) |
| { |
| /* Configure the IO secure attribute */ |
| temp &= ~(GPIO_SECCFGR_SEC0 << position) ; |
| temp |= (PinAttributes << position); |
| } |
| position++; |
| } |
| |
| /* Set secure attributes */ |
| GPIOx->SECCFGR = temp; |
| } |
| |
| /** |
| * @brief Get the GPIO pins attributes. |
| * @note Available attributes are to secure GPIO pin(s), so this function is |
| * only available in secure |
| * @param GPIOx where x can be (A..H) to select the GPIO peripheral for STM32L5 family |
| * @param GPIO_Pin specifies the single pin to get the secure attribute from |
| * @param pPinAttributes pointer to return the pin attributes. |
| * @retval HAL Status. |
| */ |
| HAL_StatusTypeDef HAL_GPIO_GetConfigPinAttributes(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, uint32_t *pPinAttributes) |
| { |
| uint32_t position = 0U; |
| uint32_t iocurrent; |
| |
| /* Check null pointer */ |
| if(pPinAttributes == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the parameters */ |
| assert_param(IS_GPIO_ALL_INSTANCE(GPIOx)); |
| assert_param(IS_GPIO_PIN(GPIO_Pin) && (GPIO_Pin != GPIO_PIN_All)); |
| |
| /* Get secure attribute of the port pin */ |
| while ((GPIO_Pin >> position) != 0U) |
| { |
| /* Get current io position */ |
| iocurrent = GPIO_Pin & (1UL << position); |
| |
| if(iocurrent != 0U) |
| { |
| /* Get the IO secure attribute */ |
| if((GPIOx->SECCFGR & (GPIO_SECCFGR_SEC0 << position)) != 0U) |
| { |
| *pPinAttributes = GPIO_PIN_SEC; |
| } |
| else |
| { |
| *pPinAttributes = GPIO_PIN_NSEC; |
| } |
| |
| break; |
| } |
| position++; |
| } |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* __ARM_FEATURE_CMSE */ |
| |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* HAL_GPIO_MODULE_ENABLED */ |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |
